ComOne MC223 : eth0 failed

2004-11-23
2013-04-08
  • Florent Morel

    Florent Morel - 2004-11-23

    Hi everyone.

    I'm having troubles configuring my PCMCIA card.

    As the subect said, it's a ComOne (don't blame me, i didn't chose the manufacturer ;o).

    The point is : it seems to be recognized (see after) but when i come to bring up eth0, it fails.

    I tried to put some lines in /etc/pcmcia/config.opts as described in the PCMCIA-HOWTO, but nohing seems to work.

    My question is : is it a configuration problem OR is it a card problem (if it is, i'll need some help on how to get unstuck from this :o)

    here are the informations I stored about my card :

    linux:/home/flo # lspci -v

    0000:00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
    Subsystem: Compaq Computer Corporation: Unknown device b103
    Flags: bus master, medium devsel, latency 168, IRQ 11
    Memory at 10000000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
    Memory window 0: 10400000-107ff000 (prefetchable)
    Memory window 1: 10800000-10bff000
    I/O window 0: 00004000-000040ff
    I/O window 1: 00004400-000044ff
    16-bit legacy interface ports at 0001

    linux:/home/flo # cardctl config
    Socket 0:
    Vcc 5.0V Vpp1 0.0V Vpp2 0.0V
    interface type is "memory and I/O"
    irq 10 [exclusive] [level]
    speaker output is enabled
    function 0:
    config base 0x0420
    option 0x45 status 0x08 pin 0x00 ext 0x00
    io 0x03f8-0x03ff [8bit]

    linux:/home/flo # cardctl info
    PRODID_1="COM1 SA"
    PRODID_2="MC223 CARD"
    PRODID_3="NOKIA 6110"
    PRODID_4="4T129000000UXX"
    MANFID=ffff,0601
    FUNCID=2

    linux:/etc/pcmcia # cardctl status
    Socket 0:
    5V 16-bit PC Card
    function 0: [ready]

    linux:/etc/pcmcia # cat /var/lib/pcmcia/stab
    Socket 0: Serial or Modem
    0 serial serial_cs 0 ttyS0 4 64

    Thanks for your help !

    take care.

     
    • Florent Morel

      Florent Morel - 2004-11-23

      I forgot :

      I'm using Mepis 2004 on 2.6.7 (but it was the same problem on RH9 2.4.x an SuSE9.1 2.6.x)
      cardctl version 3.2.5

      the config.opts i tried :
      #test
      card "COM1 SA GSM ISDN LAN"
        version "COM1 SA", "MC223 CARD", "NOKIA 6110", "4T129000000UXX"
      manfid 0xffff, 0x0601

      it doesn't work :o(

      I also went on the manufacturer web site and it said :

      GNU/Linux compatibility :
      - MC223 Platinium Card 3 in 1
      Not compatible for ISDN, GSM may work (not tested), LAN not tested.

      So i'd like to test this LAN feature.

      thanks for your attention

       
      • David Hinds

        David Hinds - 2004-11-25

        I have no information about this card.  Based on what you've posted, the card is identifying itself as a serial port device and that is how it was configured.  It is sometimes difficult to support multifunction cards without information from the manufacturer.  Can you also post the output of 'dump_cis'?

        --Dave

         
    • Florent Morel

      Florent Morel - 2004-11-29

      Hi dave, here is the outpout of dump_cis

      # dump_cis
      Socket 0:
        dev_info
          no_info
        attr_dev_info
          no_info
        vers_1 4.1, "COM1 SA", "MC223 CARD", "NOKIA 6110", "4T129000000UXX"
        manfid 0xffff, 0x0601
        funcid serial_port
        funcid multi_function
        funcid network_adapter
        config base 0x0420 mask 0x0077 last_index 0x0d
        cftable_entry 0x05 [default]
          [mwait]
          io 0x03f8-0x03ff [lines=10] [8bit] [range]
          irq mask 0x86bc [level] [shared]
          memory 0xfff000-0xffffff @ 0x0000
        cftable_entry 0x05
          io 0x02f8-0x02ff [lines=10] [8bit] [range]
        cftable_entry 0x05
          io 0x03e8-0x03ef [lines=10] [8bit] [range]
        cftable_entry 0x05
          io 0x02e8-0x02ef [lines=10] [8bit] [range]
        cftable_entry 0x0d
          io 0x0000-0x0007 [lines=10] [8bit] [range]

      hope it helps.

      If the manufacturer information are required, i'll need your help on what to ask (and how to ask ;o).

      regards,

      flo

       
      • David Hinds

        David Hinds - 2004-12-20

        Well, you would need to find out how to configure the network side of the card, and also what chip set is used for the network function.

        -- Dave

         

Get latest updates about Open Source Projects, Conferences and News.

Sign up for the SourceForge newsletter:





No, thanks