[Openocd-svn] r2504 - in trunk/tcl: board target

[oharboe at B. <oh...@ma...>]

Author: oharboe
Date: 2009-07-10 09:21:12 +0200 (Fri, 10 Jul 2009)
New Revision: 2504

Added:
   trunk/tcl/board/ek-lm3s3748.cfg
Modified:
   trunk/tcl/target/lm3s3748.cfg
Log:
David Brownell <da...@pa...> split EK board support out
from the target CPU support .

Added: trunk/tcl/board/ek-lm3s3748.cfg
===================================================================
--- trunk/tcl/board/ek-lm3s3748.cfg	2009-07-08 22:26:42 UTC (rev 2503)
+++ trunk/tcl/board/ek-lm3s3748.cfg	2009-07-10 07:21:12 UTC (rev 2504)
@@ -0,0 +1,17 @@
+# Stellaris lm3s3748 Evaluation Kit
+#  http://www.luminarymicro.com/products/lm3s3748_usb_h_d_evaluation_kits.html
+
+# NOTE:  to use the on-board FT2232 JTAG interface:
+#  source [find interface/luminary.cfg]
+
+source [find target/lm3s3748.cfg]
+
+# LM3S parts don't support RTCK
+jtag_khz 500
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+# Board has only srst
+reset_config srst_only
+

Modified: trunk/tcl/target/lm3s3748.cfg
===================================================================
--- trunk/tcl/target/lm3s3748.cfg	2009-07-08 22:26:42 UTC (rev 2503)
+++ trunk/tcl/target/lm3s3748.cfg	2009-07-10 07:21:12 UTC (rev 2504)
@@ -1,7 +1,4 @@
-# Script for luminary lm3s3748
-#
-# NB! work in progress! Duplicated from lm3s811.cfg, but does
-# it need modification??
+# TI/Luminary Stellaris lm3s3748
 
 if { [info exists CHIPNAME] } {	
    set  _CHIPNAME $CHIPNAME    
@@ -19,31 +16,21 @@
 if { [info exists CPUTAPID ] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # force an error till we get a good number
    set _CPUTAPID 0x3ba00477
 }
 
-# RCLK 
-jtag_khz 500
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#lm3s3748 Evaluation Board has only srst
-reset_config srst_only
-
-#jtag scan chain
+# JTAG scan chain
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf -expected-id $_CPUTAPID
 
+# The "lm3s" variant works around an erratum when using Rev A of "DustDevil"
+# parts (third generation, includes LM3S3748).  It keeps the debug registers
+# from being cleared, by using software reset not SRST; NOP on newer revs.
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME cortex_m3 -endian $_ENDIAN \
+	-chain-position $_TARGETNAME -variant lm3s
 
-# the luminary variant causes a software reset rather than asserting SRST
-# this stops the debug registers from being cleared
-# this will be fixed in later revisions of silicon
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -variant lm3s
+# 8k working area at base of ram, not backed up
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 0x2000
 
-# 8k working area at base of ram
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x2000 -work-area-backup 0
-
-#flash configuration
+# flash configuration -- one bank of 128K
 flash bank stellaris 0 0 0 0 0