OpenObex with NEC e616

Help
Ian
2005-08-12
2013-05-01
  • Ian

    Ian - 2005-08-12

    Greetings people.

    First up, let me say I'm a noob at Linux, though I am trying (or so I've been told).
    I was following a how-to (http://members.dodo.com.au/~joaniemrc/nokia/Nokia-6670-USB.html) and doing nicely.  Got it all installed.  Tried to test it, but it didn't recognize my phone (NEC e616 using USB cable).  Why?

    Is there anything more I can do to try and get OpenObex to recognize my phone?  It came with software in Windows, which uses Obex exchanges, so I assume it should work in Linux also.

    Following various instructions from the how-to, I found out this information from lsusb:
    [root@localhost ian]# lsusb
    Bus 003 Device 001: ID 0000:0000
    Bus 002 Device 004: ID 0409:010c NEC Corp.
    Bus 002 Device 002: ID 1267:0210
    Bus 002 Device 001: ID 0000:0000
    Bus 001 Device 001: ID 0000:0000

    And this from /proc/bus/usb/devices
    T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
    P:  Vendor=0409 ProdID=010c Rev= 1.00
    S:  Manufacturer=NEC
    S:  Product=NEC 616
    S:  SerialNumber=352282007203200
    C:* #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=88 Prot=01 Driver=(none)
    E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=16ms
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
    E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    I:  If#= 2 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
    I:  If#= 2 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
    E:  Ad=84(I) Atr=01(Isoc) MxPS=  16 Ivl=1ms
    E:  Ad=05(O) Atr=01(Isoc) MxPS=  16 Ivl=1ms
    I:  If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=88 Prot=01 Driver=(none)
    E:  Ad=86(I) Atr=03(Int.) MxPS=  16 Ivl=16ms
    I:  If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
    E:  Ad=87(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    E:  Ad=08(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    I:  If#= 5 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=88 Prot=01 Driver=(none)
    E:  Ad=89(I) Atr=03(Int.) MxPS=  16 Ivl=16ms

    So Linux is recognizing my phone is attached, but when I run obex_test, this is all I get:
    [ian@localhost src]$ ./obex_test -u
    Using USB transport, querying available interfaces
    Use './obex_test -u interface_number' to run interactive OBEX test client

    No interfaces.  Any suggestions?

    Cheers,
    Ian

     
    • Ian

      Ian - 2005-08-12

      As soon as I posted, I realised I should have made the subject more descriptive... all the posts in here are to do with OpenObex!

      Also, I am setting my phone to accept usb connections, the same way I have to do in Windows.

       
    • Christian W. Zuckschwerdt

      Since the usb vendor/device is proprietary it won't be recognized. Are you able to run a terminal (tty) over the usb interface? I.e. can you send AT commands to the phone?

       
    • Ian

      Ian - 2005-10-07

      Hi Christian,
      Thanks for replying.  I'd just about given up.

      As I said, I'm a linux noob, so I don't really understand.  How would I run (open?) a terminal over usb?  I checked /dev/ for a ttyUSB after googling for usb terminals, but couldn't find any.

      I have sent AT commands to modems in the past though.  I understand that much.

      Cheers,
      Ian

       
      • Christian W. Zuckschwerdt

        If there is not /dev/ttxUSB* you are out of luck. Sorry. You need to look for a linux kernel module that supports the vendor/product id of your phone. It will supply the tty and enable e.g. obex. I don't think there is a module though.

         

Log in to post a comment.