Further to my previous post, I continued to run the openhantek app and noticed that on two occasions the LED, to the left of the Ch1 connector, started to flash and continued to do so for a long time. According to the help on the app, this would seem to indicate that the app was trying (unsuccessfully) to upload the firmware to the device. I thought that I should mention this as it seems indicate that the app is (sometimes) recognising the device.
I have downloaded openhantek_20210714-7483fb2-1_osx_x86_64.dmg from https://github.com/OpenHantek/OpenHantek6022/releases) and run it on macOS 10.15.7 Catalina. It starts by showing a "Select Device" window, listing DSO-6022BL as one of the supported device, but fails to detect it. It does run, apparently correctly, in demo mode when I select that. The scope appears in the masoS system report under USB as Vendor-Specific Device: Product ID: 0x602a Vendor ID: 0x04b4 (Cypress Semiconductor) What might...
Konrad, thanks for the response. I am using pre-compiled OpenHantek for Windows 10. My scope is Hantek 6022BE Best regards Marko
I am using pre-compiled OpenHantek for Windows 10. My scope is Hantek 6022BE Best regards Marko
It would be useful to know which scope you are using and which operating system you are compiling OpenHantek for. I'm a newbie here and still learning.
Hi I'm new on this forum regarding my Hantek DSO5202BM. I'm running Windows 10. I have upgraded the scope to 3.30.0 (180226.0) firmware. I'm trying not to have to shell out money on a new scope only because this one is not very automatable as-is. TTScope is not quite doing it for me. I would like to someday capture waveforms in a .csv format instead of a .bmp format. It would really be awesome to get it to understand SCPI commands. It looks like there's some hope. TTScope looks like it has access...
Hi I'm new on this forum regarding my Hantek DSO5202BM. I'm running Windows 10. I'm trying not to have to shell out money on a new scope only because this one is not very automatable as-is. TTScope is not quite doing it for me. I would like to someday capture waveforms in a .csv format instead of a .bmp format. It would really be awesome to get it to understand SCPI commands. It looks like there's some hope. TTScope looks like it has access to all of the front panel buttons. My first steps are to...
Hi I'm new on this forum regarding my Hantek DSO5202BM. I'm trying not to have to shell out money on a new scope only because this one is not very automatable as-is. TTScope is not quite doing it for me. I would like to someday capture waveforms in a .csv format instead of a .bmp format. It would really be awesome to get it to understand SCPI commands. It looks like there's some hope. TTScope looks like it has access to all of the front panel buttons. My first steps are to compile an image for my...
Hello all, I am using OpenHantek for several years and each new version is better. For last few years I used version 3.2. Today I was working for about an half of hour and then program suddenly stopped working. When I restarted program, there was no error, plot appeared and after 2 s program simply crushed. I tried also the most recent version 3.2.3 with the same result. I was already scared that scope is somehow dead. (I was working with voltages 0V - 12V and I used 10x setting on probes.) Fortunately...
Hello all, I am using OpenHantek for several years and each new version is better. For last few years I used version 3.2. Today I was working for about an half of hour and then program suddenly stopped working. When I restarted program, there was no error, plot appeared and after 2 s program simply crushed. I tried also the most recent version 3.2.3 with the same result. I was already scared that scope is somehow dead. (I was working with voltages 0V - 12V and I used 10x setting on probes.) Fortunately...
Hi, in the documentation for building under Windows you mention the need for QtMake -- is there a free version of Qt that can be used ?? Is a seperate C++ compiler/toolchain needed ?? If so which is best ?? Regards, Bob
Has anyone have any experience with this isolator and Hantek 6022BE scopes under OpenHantek ?? Many isolators will not run at 480Mb/s and so the 6022 will not be found. The isolator indicated above claims to run at 480Mb/s but I'd like to confirm this before I buy. Thanks in advance,
Hi Carl Type: sudo make install Regards Brendan From: "Cail Parsons" akharucail@users.sf.net To: "[openhantek:discussion] " 1153137@discussion.openhantek.p.re.sf.net Subject: [openhantek:discussion] getting error in 'make install' Date: 22/07/2017, 21:55 Hi, i am very new to ubuntu and code in general. i have been intalling openhantek. i was told to: After you've installed the requirements run the following commands inside the directory of this package: $ qmake $ make $ make install when i get to...
Hi, i am very new to ubuntu and code in general. i have been intalling openhantek. i was told to: After you've installed the requirements run the following commands inside the directory of this package: $ qmake $ make $ make install when i get to the $ make install i get this error cail@AkHaruCailness:~/Downloads/openhantek$ make install install -m 755 -p "bin/openhantek" "/usr/local/bin/openhantek" install: cannot create regular file '/usr/local/bin/openhantek': Permission denied Makefile:558: recipe...
Hi I know it is a rather old post I answer, but I have succesfully installed https://github.com/swkim01/openhantek.git...
Hi, after a lot of trying and working through internet forums, I actually managed...
Since this issue can still be found on Ubuntu (and presumably debian), here's what...
Since this issue can still be found on Ubuntu (and presumably debian), here's what...
after some fiddeling around on another more default jessie system i got the software...
hi, i would like to use this software but ran into some compile problems: ~/Downloads/OpenHantek-openhantek-342cac5/build$...
hi, i would like to use this software but ran into some compile problems: ~/Downloads/OpenHantek-openhantek-342cac5/build$...
I recently purchased a DSO3064A and a DSO2000. My goal is to store waveforms running...
Hi Jonas ... Sorry, I can't help you with your own issue ... however ... I'm wondering...
Builds fails with Qt5
Just installed the openhantek on Ubuntu. It worked perfectly, so thank you very much,...
Anyone using Hantek6022BL with success!? I'm having trouble linking extractfw and...
Has anyone gotten openhantek to work on a DSO-5200A? I just bought this unit and...
Hi! I'm trying to access the website, but I get some python error? ========= ImportError...
Finally I managed to get openHantek running with my dso2090. AS mentioned above I...
Finally I managed to get openHantek running with my dso2090. AS mentioned above I...
I just wrote a simple patch which adds minimal and maximal voltage to display. I...
I am relatively new to Linux (Ubuntu 14.04), so it took a while to find out how to...
DSO-6022BE Support