ControllerSetup

Setting up the controller.ini

Nintendont requires the sd:/controller.ini file when run on a Wii U, on a Wii this file is optional.

When using Nintendont on Wii U HID is automatically enabled, it won't boot any game when no controller is connected.

The file can only contain one controller config at a time.

Creating a new controller.ini for your controller

You need my tool called HIDTest to determinate the values.

Most entries should be obvious.

All values are in hex, do not use the 0x prefix.

Polltype:

Use 1 (so far only the PS3 controller needed 0)

DPAD:

Certain pads use bits for each DPad direction other use numbers going

form 0 to 7 for each direction.

An easy test for this is if one direction doesn't change any bits then

use 1 and fill in all 8 values for the DPAD otherwise use 0 and just fill

in the four values. (see examples)

DigitalLR:

If your pad doesn't have analog triggers for L and R, set this to 1.

It will consider the trigger buttons as fully pressed when you use L or R.

MultiIn:

Certain USB adapters have multiple inputs here you can select

which port data to use.

First set MultiIn=1 and then set MultiInValue to either 0,1,2,..

it depends on the adapter and the port you are using.

The rest uses [Button]=[offset],[mask] offset starts at 0.

[Anonymous]

Originally posted by: juanseba...@gmail.com

my controller does math error usb message: controller.ini

[Anonymous]

Originally posted by: Atze91...@googlemail.com

Add pls a controller.ini for Speedlink Strike2

[Anonymous]

Originally posted by: afernan...@gmail.com

Add a vibration/rumble in USB version of rumblepad 2, please

[Anonymous]

Originally posted by: juanseba...@gmail.com

in the hid test my values changed me my problem is that the file can not find controller.ini I use a usb control nintendont here I leave the link of the image:

[Anonymous]

Originally posted by: anjosm...@gmail.com

Hey I have no idea where the best place to post this is but I've done some testing with the Wii U GC adapter on nintendont with melee. Dash dancing consistently is really difficult. I have zero hex or coding exp so all I can do is just tell you how it feels.

Everyone who used my setup had trouble dash dancing.

If I slam the stick really hard, I can consistently dash dance. If I try to do it like I normally would on a GC or Wii the character will fail to turn around after a couple successful dashes.

I think the threshold for dashing is too high, or not enough angles are being registered as a left and right input. It feel a little bit furthest i can press the stick on the GC controller isn't being registered as the furthest a GC controller stick can be pressed if you catch my drift. If you've used dolphin, it is kinda like the Radius isn't set to 100 in gamepad settings.

[Anonymous]

Originally posted by: etwartown

Hello! My question is not related with the setup, but How can I submit my own controller.ini to your list? I placed my ini file in controllers directory (renamed to "11FF_3331.ini" in order to match with VID and PID) and it worked perfectly, so, Should I send the ini file to you?, or What I should do?.

[Anonymous]

Originally posted by: bence0...@gmail.com

Hi. Umm I have a small problem. I've got the Wii U pro controller and Nintendont now. So I got the appropriate controllerconfig.ini and that is in the root on the SD and Super MArio Sunshine. My problem is that when I play it it feels that the controller doesn't always "feels" my input and don't do anything I tried turning off the turbo but that didn't help. Any suggestions?

[Anonymous]

Originally posted by: tarikalm...@gmail.com

Is there any chance to change the button mapping of the Wii Classic Controller? I'm aware of the possibility to turn all fire buttons by 90° but I want to map each manually. Is that possible?

[Anonymous]

Originally posted by: fjtr...@gmail.com

Hello I'm trying to configure the controller_ps2 to multiplayer. My device is a Woxter ps2 to ps3/PC

The ID of the device is VID=0810 PID=0001

I'm putting MultiIn?=2 but I don't know what I have to put in the MultiInValue? line. I have tried with 01, 00, 02 but the controller 1 move the controller 2 and also the reverse. Can you help me? Thank you in advance.

[Anonymous]

Originally posted by: zlqt...@gmail.com

I have the same issue from the post above me! somebody?

[Anonymous]

Originally posted by: ruffone...@gmail.com

any way to power off the wii controller...??

[Anonymous]

Originally posted by: dark-yos...@hotmail.com

Is there a way to use 4 or 2 controllers (PC) USB Gamepads? using an usb multiplicator? Like that?. Because it only lets me use just one controller

[Anonymous]

Originally posted by: alex.bus...@gmail.com

Is the source available for HIDTest?

[Anonymous]

Originally posted by: jan.hon...@gmail.com

Is there any option how to get Logitech F310 recognized in XInput mode on Wii?

[Anonymous]

Originally posted by: ricardo.urbina

Is there any way to use the Wii remote + nunchuck? At first sight it looks like there aren't enough buttons/sticks, but actually there's more than enough to play, say, Mario Kart Double Dash! If Wii U Pro pads work, I don't see why the ordinary Wii remote wouldn't.

[Anonymous]

Originally posted by: Harrison...@gmail.com

Hi guys, I need help, kind of urgent

I have been playing Sonic Heroes with the Wiimote and Nunchuck, but I have this weird problem where the camera is randomly rotating when I tilt the nunchuck. Is there any fix for this? I don't care for the second stick (What I believe the camera is) and so it can be removed from the controls for all I care. My gamecube controllers should arrive in a week, removing the need for this so a reply ASAP would be great.

Thanks

[Anonymous]

Originally posted by: joubert....@gmail.com

I put DigitalLR:1, but don't work, the analogL and AnalogR will be set as ?

[Anonymous]

Originally posted by: xzionxn...@hotmail.com

where do i have to put the .ini controller to make it work? i have the ps2 usb ini and the logitec dual action :O ,cant get them to work..,my game cube controller is fuckt up

[Anonymous]

Originally posted by: stfumin...@gmail.com

@fjtr Same here but mine doesnt say woxter. Max pads set to 0. Works perfectly fine on pc n android Does your multiinvalue=02 only let 1 controller work too?

Also why does the analogue button need to be pressed again on game load?

[Anonymous]

Originally posted by: stfumin...@gmail.com

Oh yeah @developer i could send the drivers if thatt heelps. Someone on gbatemp had the same peoblem but was ignored after he mentioned unofficial controllers. Mine are official though and gbatemp is being a jeb loading so i can't sign up to ask there. Thanks

[Anonymous]

Originally posted by: ChipN...@gmail.com

Could someone very simply explain to me how I can switch buttons on an already made ini? The PS3 one works wonderfully, althoogh I'd prefer to switch the square and cross under certain games, where the cross button would be more natural for jumping.

[Anonymous]

Originally posted by: sio2481...@gmail.com

I want a PC HID controller (VID=0079 - PID=0006) and a PS3 Controller (VID=054C - PID=0268) use together! What should I set so that I can use 2 players for multiplayer??? Or what Multiin adapter do I need?