I have ncidd running (OS X 10.4.6) just fine, but neither ncid nor ncid picks up the messages, whether on the same computer or over the network.
Here's part of the log file:
Started 05/10/2006 14:24
Configured to send 'cidlog' to clients.
Configured to send 'cidinfo' to clients.
Processed config file: /usr/local/etc/ncid/ncidd.conf
Processed alias file: /usr/local/etc/ncid/ncidd.alias
CID logfile: /var/log/cidcall.log
Data logfile: /var/log/ciddata.log
TTY port opened: /dev/cu.modem
TTY port speed: 19200
TTY lock file: /var/lock/LCK..cu.modem
TTY port control signals disabled
ATE1V1Q0
OK
OK
Modem initialized.
AT+FCLASS=8;+VCID=1
OK
Modem set for CallerID.
polld[1].revents: 0x1, fd: 7
Client connected, sd: 8, Sent call log: /var/log/cidcall.log
polld[1].revents: 0x1, fd: 7
Client connected, sd: 9, Sent call log: /var/log/cidcall.log
polld[1].revents: 0x1, fd: 7
Client connected, sd: 10, Sent call log: /var/log/cidcall.log
polld[0].revents: 0x1, fd: 6
RX
polld[0].revents: 0x1, fd: 6
Send me the debug output. Also create /var/ciddata.log and run program again. Send me ciddata.log. From what I see above, the modem outputs XNAME instead of NAME. I can take that into account.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I have ncidd running (OS X 10.4.6) just fine, but neither ncid nor ncid picks up the messages, whether on the same computer or over the network.
Here's part of the log file:
Started 05/10/2006 14:24
Configured to send 'cidlog' to clients.
Configured to send 'cidinfo' to clients.
Processed config file: /usr/local/etc/ncid/ncidd.conf
Processed alias file: /usr/local/etc/ncid/ncidd.alias
CID logfile: /var/log/cidcall.log
Data logfile: /var/log/ciddata.log
TTY port opened: /dev/cu.modem
TTY port speed: 19200
TTY lock file: /var/lock/LCK..cu.modem
TTY port control signals disabled
ATE1V1Q0
OK
OK
Modem initialized.
AT+FCLASS=8;+VCID=1
OK
Modem set for CallerID.
polld[1].revents: 0x1, fd: 7
Client connected, sd: 8, Sent call log: /var/log/cidcall.log
polld[1].revents: 0x1, fd: 7
Client connected, sd: 9, Sent call log: /var/log/cidcall.log
polld[1].revents: 0x1, fd: 7
Client connected, sd: 10, Sent call log: /var/log/cidcall.log
polld[0].revents: 0x1, fd: 6
RX
polld[0].revents: 0x1, fd: 6
polld[0].revents: 0x1, fd: 6
DATE = 0510
polld[0].revents: 0x1, fd: 6
polld[0].revents: 0x1, fd: 6
TIME = 1424
polld[0].revents: 0x1, fd: 6
polld[0].revents: 0x1, fd: 6
NMBR = xxxxxxxxxx
polld[0].revents: 0x1, fd: 6
polld[0].revents: 0x1, fd: 6
.XNAME = NEW JERSEY
polld[0].revents: 0x1, fd: 6
and so on. Is there some additional daemon I should be running?
Thanks,
Steve
Send me the debug output. Also create /var/ciddata.log and run program again. Send me ciddata.log. From what I see above, the modem outputs XNAME instead of NAME. I can take that into account.