Hi,
I have already made several versions of the MyfocuserPro2 and everything is fine
works. I installed a home position switch on my telescope. Now I have ventured to the ESP version and have a problem with the home position switch. If I move the switch manually or with the Windwostool, i.e. if it trips, this is recognized by the firmware and also stops. However, action is triggered to move the motor out of the zero position. The switch is still triggered and I can no longer trigger any movement. The engine just hums, nothing more. What could that be, can you help me ?
Best Regards
Frank
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Please email me direct. Address in firmware file. attach error log file to the email. I will not troubleshoot here in the forum.
pg 14 of PDF
WHAT YOU NEED TO PROVIDE WHEN ASKING FOR HELP
• A detailed explanation of the problem outlining what happens and steps required to reproduce the problem
• Your focuserconfig.h and myboards.h file so we know how to reproduce your settings
• A copy of your data_per.jsn file is very useful [see here how to get this file]
• Any modifications you have made to the existing official release code [as we assume you are using
the official release unmodified you will be asked to only use the existing official release code; no
support is available to help debug your code alterations]
• We assume that you are using the current recommended versions of Arduino, Packages and
Libraries as outlined in the Readme.md and firmware files. If this is NOT the case, you need to
specify what these versions are so we can recreate that environment]
• Your network TCIP/IP addresses [we do NOT require your SSID or PASSWORD]
Last edit: brownrb 2020-05-19
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Sending email to you directly will not work. Emails to
brownrb@users.sourceforge.net will be rejected by the mail system. I need a
valid email address.
Hi,
I have already made several versions of the MyfocuserPro2 and everything is fine
works. I installed a home position switch on my telescope. Now I have ventured to the ESP version and have a problem with the home position switch. If I move the switch manually or with the Windwostool, i.e. if it trips, this is recognized by the firmware and also stops. However, action is triggered to move the motor out of the zero position. The switch is still triggered and I can no longer trigger any movement. The engine just hums, nothing more. What could that be, can you help me ?
Best Regards
Frank
Please email me direct. Address in firmware file.
You will need to send me a log file with HPSW enabled
Regards
Robert
Hi Robert,
here are the log-File.
Regards
Frank
Von: brownrb brownrb@users.sourceforge.net
Gesendet: Dienstag, 19. Mai 2020 04:32
An: [myfocuserpro2-esp32:discussion]
general@discussion.myfocuserpro2-esp32.p.re.sourceforge.net
Betreff: [myfocuserpro2-esp32:discussion] Problem with HomepositionStitch
Please email me direct. Address in firmware file.
You will need to send me a log file with HPSW enabled
Regards
Robert
Problem with HomepositionStitch
https://sourceforge.net/p/myfocuserpro2-esp32/discussion/general/thread/8aa cce59ea/?limit=25#42bb
Sent from sourceforge.net because you indicated interest in
https://sourceforge.net/p/myfocuserpro2-esp32/discussion/general/
To unsubscribe from further messages, please visit
https://sourceforge.net/auth/subscriptions/
--
Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft.
https://www.avast.com/antivirus
Please email me direct. Address in firmware file. attach error log file to the email. I will not troubleshoot here in the forum.
pg 14 of PDF
WHAT YOU NEED TO PROVIDE WHEN ASKING FOR HELP
• A detailed explanation of the problem outlining what happens and steps required to reproduce the problem
• Your focuserconfig.h and myboards.h file so we know how to reproduce your settings
• A copy of your data_per.jsn file is very useful [see here how to get this file]
• Any modifications you have made to the existing official release code [as we assume you are using
the official release unmodified you will be asked to only use the existing official release code; no
support is available to help debug your code alterations]
• We assume that you are using the current recommended versions of Arduino, Packages and
Libraries as outlined in the Readme.md and firmware files. If this is NOT the case, you need to
specify what these versions are so we can recreate that environment]
• Your network TCIP/IP addresses [we do NOT require your SSID or PASSWORD]
Last edit: brownrb 2020-05-19
Hallo Robert,
Sending email to you directly will not work. Emails to
brownrb@users.sourceforge.net will be rejected by the mail system. I need a
valid email address.
Or am I making a mistake in thinking.
Regards
Frank
Von: brownrb brownrb@users.sourceforge.net
Gesendet: Dienstag, 19. Mai 2020 08:45
An: [myfocuserpro2-esp32:discussion]
general@discussion.myfocuserpro2-esp32.p.re.sourceforge.net
Betreff: [myfocuserpro2-esp32:discussion] Problem with HomepositionStitch
Please email me direct. Address in firmware file. attach error log file to
the email. I will not troubleshoot here in the forum.
Problem with HomepositionStitch
https://sourceforge.net/p/myfocuserpro2-esp32/discussion/general/thread/8aa cce59ea/?limit=25#b5eb
Sent from sourceforge.net because you indicated interest in
https://sourceforge.net/p/myfocuserpro2-esp32/discussion/general/
To unsubscribe from further messages, please visit
https://sourceforge.net/auth/subscriptions/
--
Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft.
https://www.avast.com/antivirus
Please email me direct. Address in firmware file.
Specifically,
Read line 29 of the firmware file. It has an email address.