Yes, I know why. I actually do not use OLEDGRAPHICS. That code is maintained by another. So it is not on my test plan. I have loaded a fix and will upload a replacement for v104 now, today.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I am not sure whether I will use OLEDGRAPHICS either, no dea at this point what text or graphics looks like, but looking forward to get it running with the IR remote, which is my main reason for upgrading from the earlier esp 8266 version.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
There is also a section in 15 Controller Features that checks for LCDDISPLAY and OLEDDISPLAY and neitherof these appear to have definitions, perhaps leftover from previous versions. Dont know if this is an issue.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
I am struggling a bit. Switched to OLED TEXT am getting as far as "setup end" and thats it. Not sure what it should do next. I can access via the webserver but does not seem to do anything and also installed windows app on a different pc on the same network and cant get it to connect. Any pointers?
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Make sure you set the target board type in myboards.h
make sure you set the correct target cpu in Arduino IDE
You will need to include everything you have enabled (I must know what options you have enabled), it is best to watch the videos on you tube also.
I can access via the webserver but does not seem to do anything
In webserver mode you can access the webserver. So if you do a move, after the screen refereshes (wait for this to happen after clicking a move) you should see new position. Again there is a video on youtube for the web server.
You can try entering a new position and then set.
Again wait for the screen to refresh (may take 10-30s) and not if its been updated.
In your email best to send me the zip of your modified firmware to look at and review/
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
ESP32DRV8825 used with the software for windows. If I click on the option to set the reverse rotation of the motor nothing happens. The direction of rotation does not change ... Why?
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
ESP32DRV8825 used with the software for windows. If I click on the option to set the reverse rotation of the motor nothing happens. The direction of rotation does not change ... Why?
Hi Corrado
Thank you for you patience and testing. I very much appreciate it.
I have some files for you to test firmware release 020 and windows app 2036
i believe these will resolve your issue.
Please email me direct (address in firmware.ino file) so I can send you the download links
regards
Robert
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Build fails when TEMPERATUREPROBE not defined and OLEDGRAPHICS defined.
Line 1271 in myFP2ESP.ino calls readtemp when TEMPERATUREPROBE not defined.
Last edit: Jimboh2 2019-12-08
Yes, I know why. I actually do not use OLEDGRAPHICS. That code is maintained by another. So it is not on my test plan. I have loaded a fix and will upload a replacement for v104 now, today.
I am not sure whether I will use OLEDGRAPHICS either, no dea at this point what text or graphics looks like, but looking forward to get it running with the IR remote, which is my main reason for upgrading from the earlier esp 8266 version.
In other future releases here on sourceforge only oledtext is an option
There is also a section in 15 Controller Features that checks for LCDDISPLAY and OLEDDISPLAY and neitherof these appear to have definitions, perhaps leftover from previous versions. Dont know if this is an issue.
This is ok and fixed from release 105
I am struggling a bit. Switched to OLED TEXT am getting as far as "setup end" and thats it. Not sure what it should do next. I can access via the webserver but does not seem to do anything and also installed windows app on a different pc on the same network and cant get it to connect. Any pointers?
Contact me direct at email n firmware.
You will need to include everything you have enabled (I must know what options you have enabled), it is best to watch the videos on you tube also.
In webserver mode you can access the webserver. So if you do a move, after the screen refereshes (wait for this to happen after clicking a move) you should see new position. Again there is a video on youtube for the web server.
You can try entering a new position and then set.
Again wait for the screen to refresh (may take 10-30s) and not if its been updated.
In your email best to send me the zip of your modified firmware to look at and review/
ESP32DRV8825 used with the software for windows. If I click on the option to set the reverse rotation of the motor nothing happens. The direction of rotation does not change ... Why?
start the app.
enable logging
connect
move the motor 100 steps
change the reverse direction
move the motor 100 steps
send me the log file
what firmware are you using
what app version are you using
If you click -100 and then +100 the motor moves in opposite steps right?
ESP32DRV8825 used with the software for windows. If I click on the option to set the reverse rotation of the motor nothing happens. The direction of rotation does not change ... Why?
Bug Report
Sent from sourceforge.net because you indicated interest in https://sourceforge.net/p/myfocuserpro2-esp32/discussion/general/
To unsubscribe from further messages, please visit https://sourceforge.net/auth/subscriptions/
I need more details
firmware version
version of windows app
your controllerconfig.h file settings
Please use my email addres as found in the firmware
Hi Corrado
Thank you for you patience and testing. I very much appreciate it.
I have some files for you to test firmware release 020 and windows app 2036
i believe these will resolve your issue.
Please email me direct (address in firmware.ino file) so I can send you the download links
regards
Robert
Now work perfect!
Thank You
…
Grazie!!!
Thank You!!
;-)