mpls-linux-general

[mpls-linux-general] LDP using problem

[<dad...@gm...>]

*Apply quagga-mpls.diff to the quagga source distribution. (0.99.6)
Go into the quagga/ldpd directory and modify 'create-links' to point to
your ldp-portable source distribution.  Then execute 'create-links' .
Go back to the top of the quagga source tree and configure and compile
quagga according to it's directions.  *
**
*After you have finished compling, you will have a ldpd binary that has
the same command line syntax as the rest of the quagga binaries.*

*'ldpd' supports LDP, zebra supports staic LSPs.*
*(if you are not familiar with quagga hit the '?' key and it will provide
you context sensitive help.  Also look at 'mpls' at the interface level.
There are also 'show' commands availble from the operations more.  Look at
'show ldp ?' and 'show mpls ?' for a list of commands.)
*

Above section is copied from README.quagga-mpls,
and then are steps I did.

1. patch quagga-0.99.6 by quagga-mpls.diff
2. execute 'delete-links'
3. modify 'create-links' and execute it.
4. back to quagga-0.99.6 folder, execute './configure --enable-mpls
--enable-ldpd --enable-vtysh'
5. compiler quagga

After compiling, ldpd binary is located in quagga-0.99.6/ldpd/
I execute zebra, ospfd, and ldpd,
and login into zebra.

But it's strange that I can only see 'show mpls ?'
There is no anything for 'show ldp ?'

Are there any steps I missed?


Thanks for youring answering.
Regard.

Re: [mpls-linux-general] LDP using problem

[Adrian P. <adr...@gm...>]

Hello,

If you don't get all the commands in vtysh, you can try to start ldpd
on a port (like port 1234) and then telnet to that port (telnet
127.0.0.1 1234), and you get in a vtysh for that protocol. I don't
remember exactly, but I think you can start ldpd -P 1234 to specify
the port.

See if there you have all the mpls ldp commands you're searching.

Good luck,
Adrian Popa

On 9/20/07, 王奕元 <dad...@gm...> wrote:
> Apply quagga-mpls.diff to the quagga source distribution. (0.99.6)
> Go into the quagga/ldpd directory and modify 'create-links' to point to
> your ldp-portable source distribution.  Then execute 'create-links' .
> Go back to the top of the quagga source tree and configure and compile
> quagga according to it's directions.
>
> After you have finished compling, you will have a ldpd binary that has
> the same command line syntax as the rest of the quagga binaries.
>
> 'ldpd' supports LDP, zebra supports staic LSPs.
> (if you are not familiar with quagga hit the '?' key and it will provide
> you context sensitive help.  Also look at 'mpls' at the interface level.
> There are also 'show' commands availble from the operations more.  Look at
> 'show ldp ?' and 'show mpls ?' for a list of commands.)
>
>
> Above section is copied from README.quagga-mpls,
> and then are steps I did.
>
> 1. patch quagga-0.99.6 by quagga-mpls.diff
> 2. execute 'delete-links'
> 3. modify 'create-links' and execute it.
> 4. back to quagga-0.99.6 folder, execute './configure --enable-mpls
> --enable-ldpd --enable-vtysh'
> 5. compiler quagga
>
> After compiling, ldpd binary is located in quagga-0.99.6/ldpd/
> I execute zebra, ospfd, and ldpd,
> and login into zebra.
>
> But it's strange that I can only see 'show mpls ?'
> There is no anything for 'show ldp ?'
>
> Are there any steps I missed?
>
>
> Thanks for youring answering.
> Regard.
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Microsoft
> Defy all challenges. Microsoft(R) Visual Studio 2005.
> http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
> _______________________________________________
> mpls-linux-general mailing list
> mpl...@li...
> https://lists.sourceforge.net/lists/listinfo/mpls-linux-general
>
>