Re: [mpls-linux-general] Egress Router, how?

[T. T. <t_t...@ho...>]

Mr. Leu

Thanks for your quick reply.

I have reset LSPs on C as following.

# mplsadm2 -L eth1:0
# mplsadm2 -A -I gen:101:0
# mplsadm2 -A -I gen:201:0
# mplsadm2 -I gen:101:0 -i pop:peek
In Instr: No such device or address

But they seemed to be set properly except the last command again.
How should I do this?

The information of the machine is

  OS : Redhat 8.0
  kernel : 2.4.22
  mpls : mpls-linux-1.172

If you could take a few minutes to answer my question, I would really 
appreciate it.

Best regards

>From: "James R. Leu" <jl...@mi...>
>Reply-To: jl...@mi...
>To: "T. Take" <t_t...@ho...>
>CC: mpl...@li...
>Subject: Re: [mpls-linux-general] Egress Router, how?
>Date: Mon, 24 May 2004 09:05:47 -0500
>
>On Mon, May 24, 2004 at 06:58:28PM +0900, T. Take wrote:
> > Hi.
> >
> > I have a similar problem.
> > I have executed "MPLS Hierarchy" in README and succeeded to setup 200 
and
> > 202 LSP.
> >
> >          101
> >   200    201    202
> > A------B------C------D
>
>Here is how I do it:
>
>on C
>----
>mplsadm2 -A -I gen:101:0
>mplsadm2 -A -I gen:201:0
>mplsadm2 -I gen:101:0 -i pop:peek
>
>on B
>----
>mplsadm2 -A -O 0
>mplsadm2 -O 0x2 -o push:gen:101:set:eth1:192.169.1.2
>mplsadm2 -A -O 0
>mplsadm2 -O 0x3 -o push:gen:201:fwd:0x2
>mplsadm2 -A -I gen:200:0
>mplsadm2 -B -I gen:200:0 -O 0x3
>
> >
> > But, I had a problem at "On C" setting about 101 and 201. The command 
is
> >
> > # mplsadm2 -I gen:101:0 -i pop:peek
> > In Instr: No such device or address
> >
> > It didn't seem to be set properly.
> > When I have executed "mplsadm2 -d", the output of the above command is
> >
> > mpls_set_in_label_instructions: enter
> > mpls_in_info_hold: enter
> > mpls_in_info_hold: new count 2
> > mpls_in_info_hold: exit
> > mpls_instruction_build: enter
> > mpls_instruction_build: exit(2)
> > mpls_instruction_clear: enter
> > mpls_instruction_clear: exit
> > mpls_in_info_release: enter
> > mpls_in_info_release: new count 1
> > mpls_in_info_release: exit
> > mpls_set_in_label_structions: exit
> >
> > What should I do?
> > I hope any help.

_________________________________________________________________
メッセンジャーで総額1億円プレゼント！ http://im.msn.co.jp/home.htm