Re: [mpls-linux-devel] New MPLS-Linux code

[James R. L. <jl...@mi...>]

On Wed, Feb 28, 2007 at 10:56:10AM +0100, Sienes Rodr?guez Gonzalo wrote:
> Hi again:
>=20
> I have configured a simple scenario. And the result, is that I'm able to =
create mpls segments from vtysh. In the sender I type: ip route 12.0.0.1 ge=
n 222 nexthop eth1 10.0.0.1, and in the receiver: mpls static 0 -> label-ma=
p gen 222 pop. With ping from sender to 12.1 I can see that the ICMP packet=
s are labelled. Also I can see the new mpls segment created by mpls nhlfe s=
how and mpls ilm show.
> So the problem must be at configuring LDP, as I told you in the "running =
config" doesn't appear mpls ip (at the required interface) or the general c=
ommand mpls ldp.

OK.  Thanks for the feedback.  I'll look into it.

> Thanks,
> Gonzalo
>=20
>=20
> -----Mensaje original-----
> De: James R. Leu [mailto:jl...@mi...]
> Enviado el: lun 26/02/2007 15:08
> Para: Sienes Rodr?guez Gonzalo
> CC: mpl...@li...
> Asunto: Re: [mpls-linux-devel] New MPLS-Linux code
> =20
> On Mon, Feb 26, 2007 at 11:32:15AM +0100, Sienes Rodr?guez Gonzalo wrote:
> > Hi James!
> >=20
> > I've installed the revised RPMs for FC4. I got kernel panic after reboo=
ting the system that I solved by typing "enforcing=3D0" at grub.conf. I hav=
e some problems with the wheel of the mouse or the USB ports but in general=
 it works right. I'm able to create MPLS static configurations. In this ver=
sion the "mpls" module has disappeared so I only load "mpls4". I launch zeb=
ra, ospfd and ldpd but I make the whole configuration by vtysh. OSPF works =
well but I can't put most of the ldpd commands, in fact, the only one that =
appears with "show running-config" is "mpls labelspace 0" in the correspond=
ing interface, Neither "mpls ldp" nor "mpls ip". Are these problems solved =
in FC5? If that's it I would like to work with FC5.
>=20
> Can you manually create MPLS segments with the 'mpls' command?
> I'll look into the issue with no ldp command in vtysh.
>=20
> > Thanks,
> >=20
> > Gonzalo.
> >=20
> > I updated the FC4 kernel RPMs.  Can you please try them?
> >=20
> > On Mon, Feb 19, 2007 at 11:47:24AM +0100, Sienes Rodr?guez Gonzalo wrot=
e:
> > > Hi James:
> > >=20
> > > I'm trying to install your new software for FC4 but I have some probl=
ems.
> > > When I try to install the kernel-2.6.18 from Source Forge for FC4 it =
makes me install lots of RPMs, most of them can be installed by "yum update=
" but I can't find the libraries libc.so.6(GLIBC_2.4) and libpcap.so.0.9.3 =
anywhere for FC4. I search for them and people talks about 64 architecture =
and I'm working with Intel(R) Pentium(R) D CPU 3.00GHz. Could you provide t=
hem to me? Witch OS are you using? Should I install FC5? =20
> > >=20
> > > Thanks in advance.
> > >=20
> > > P.D.: These are the outputs I get.
> > >=20
> > > [root@PE3 mpls-linux-1.955]# rpm -ivh kernel-2.6.18-1.2257.fc4.mpls.1=
.955.i686.rpm
> > > error: Failed dependencies:
> > >         mkinitrd >=3D 4.2.21-1 is needed by kernel-2.6.18-1.2257.fc4.=
mpls.1.955.i686
> > >         isdn4k-utils < 3.2-32 conflicts with kernel-2.6.18-1.2257.fc4=
.mpls.1.955.i686
> > >         kudzu < 1.2.5 conflicts with kernel-2.6.18-1.2257.fc4.mpls.1.=
955.i686
> > >=20
> > > [root@PE3 Requeridos]# rpm -ivh mkinitrd-4.2.21-1.i386.rpm
> > > error: Failed dependencies:
> > >         libc.so.6(GLIBC_2.4) is needed by mkinitrd-4.2.21-1.i386
> > >=20
> > > [root@PE3 Requeridos]# rpm -ivh isdn4k-utils-3.2-32.i386.rpm
> > > error: Failed dependencies:
> > >         libc.so.6(GLIBC_2.4) is needed by isdn4k-utils-3.2-32.i386
> > >         libpcap.so.0.9.3 is needed by isdn4k-utils-3.2-32.i386
> > >=20
> >=20
> >=20
> >=20
> > --=20
> > James R. Leu
> > jl...@mi...
> >=20
> >=20
> >=20
>=20
>=20
>=20
> --=20
> James R. Leu
> jl...@mi...
>=20
>=20
> -------------------------------------------------------------------------
> Take Surveys. Earn Cash. Influence the Future of IT
> Join SourceForge.net's Techsay panel and you'll get the chance to share y=
our
> opinions on IT & business topics through brief surveys-and earn cash
> http://www.techsay.com/default.php?page=3Djoin.php&p=3Dsourceforge&CID=3D=
DEVDEV
> _______________________________________________
> mpls-linux-devel mailing list
> mpl...@li...
> https://lists.sourceforge.net/lists/listinfo/mpls-linux-devel

--=20
James R. Leu
jl...@mi...