monarch-users — General mailing list for users of monarch

[Monarch-users] New install issue - CONFIG ERROR! Restart aborted.

[Dan M <da...@st...>]

I am in the process of moving an existing installation of nagios 3.2.1 
with Centreon to nagios 3.5.0 with Monarch 2.5.0. The old nagios 
installation had it's config files kind of jacked up due to a handful of 
admins working with it over the years, but I finally for everything 
tidied up to the point that I can load the config files and do a 
pre-flight test with no errors and no warnings.

I can also commit with apparently no issues, but after printing out the 
results of the "nagios -v nagios.cfg" and showing 0 warning and 0 
errors, but still reports an error. Specifically, the last few lines of 
the "commit" screen show:

Total Warnings: 0
Total Errors: 0

Things look okay - no serious problems were detected during the 
pre-flight check.
Running configuration check... CONFIG ERROR! Restart aborted. Check your 
Nagios configuration.

So, what would seem to be the problem here? I'll dig in to the source 
code and see if I can figure it out for myself, but if someone else has 
seen this before I'd appreciate a pointer.

Also, a minor issue. In the "nagios main configuration" screen I still 
see lines for aggregate_status_updates, downtime_file, and comment_file 
variables. These are no longer needed in nagios 3.5.0 (the preflight 
check indicates that all status file updates are now aggregated, and 
downtime entries and comments are now stored in the status and retention 
files.

[Monarch-users] Error on Pre Flight Test in extended_service_info.cfg

[Franz B. <fra...@co...>]

Hello!

 I have a Problem on my new Nagios3 Installation. I´m using Debian 5 and have completed the Installation of Groundwork Monitor Architect 2.5. 

Nagios(3.0.6)  is running fine without any errors but with inside the GW Monitor i will get the following Error Message  using the Pre Flight Test:

 

Error: Template 'ping-0' specified in extended service info definition could not be not found (config file '/etc/nagios3/extended_service_info.cfg', starting on line 354)

 

Here is the snip from the cfg. file, starting on line 354:

 

define serviceextinfo {

       use                        ping-0

       service_description        PING

       host_name                  vmware

}

 

Can anyone help me?

cheers,

Franz

[Monarch-users] installation problem 'Table 'monarch.setup' doesn't exist'

[Luis B. <da...@gm...>]

Hello people,

I've just installed monarch on my debian testing, once everything is
correctly (I hope so) installed, when I try to access to
http://192.168.1.169/cgi-bin/monarch.cgi
I got this message in apache's errorlog:

DBD::mysql::db selectrow_array failed: Table 'monarch.setup' doesn't exist
at /usr/local/groundwork/monarch/lib/MonarchStorProc.pm line 98.
DBD::mysql::db selectrow_array failed: Table 'monarch.setup' doesn't exist
at /usr/local/groundwork/monarch/lib/MonarchStorProc.pm line 98.
[Sat Jul 11 22:59:26 2009] [error] [client 192.168.1.170] Premature end of
script headers: monarch.cgi

Any hint about how to solve it?

Thank you in advance.

[Monarch-users] Monarch Logging of Changes to NAGIOS Configuration

[Traiano G. W. <twe...@te...>]

Hi All

Does Monarch log any details of changes to the NAGIOS configuration, for
example, any of the below:

 - time of change
 - configuration item changed

I'm currently looking through the monarch database but cannot find any
table that might serve as a change log of sorts.

Thanks in Advance,
T.

Re: [Monarch-users] Monarch not saving Contact Group info.

[Scott P. <sp...@gr...>]

There is an override checkbox that tells it to not use the template
contact group. You need to uncheck it.=20

=20

As a side note, I've had to filter monarch email queries because the
spam was too much. To find answers or post questions you will want to
visit the GroundWork forums:

=20

http://www.groundworkopensource.com/community/forums/

=20

Thanks,

=20

Scott

=20

________________________________

From: mon...@li...
[mailto:mon...@li...] On Behalf Of
Bigley,Shawn
Sent: Wednesday, December 12, 2007 4:04 AM
To: mon...@li...
Subject: [Monarch-users] Monarch not saving Contact Group info.

=20

Hi all..

I was on vacation and when I returned I was the Nagios Admin.  Actually
enjoying it so far but I have run into an issue.

I am using Monarch (GroundWork Monitor Architect 2.0) and I created a
new Host.  Worked great however when I add a contact group. I can
highlight it. I can click Add. It appears in the left hand list of
contact groups on the host page. I can click Save. It says it's saved,
but when I view the host again, my contact group is back in the right
hand "not added" list of contact groups.

Any thoughts?

Shawn

[Monarch-users] Monarch not saving Contact Group info.

[Bigley,Shawn <Sha...@ns...>]

Hi all..
I was on vacation and when I returned I was the Nagios Admin.  Actually
enjoying it so far but I have run into an issue.
I am using Monarch (GroundWork Monitor Architect 2.0) and I created a
new Host.  Worked great however when I add a contact group. I can
highlight it. I can click Add. It appears in the left hand list of
contact groups on the host page. I can click Save. It says it's saved,
but when I view the host again, my contact group is back in the right
hand "not added" list of contact groups.
Any thoughts?
Shawn

[Monarch-users] Fw: Premature end of script headers error

[<mat...@lj...>]

I managed to get it working. It was a problem with libxml2 version. I had=20
2.6.7 and XML::LibXML::Common requried 2.6.16. I upgraded libxml2,=20
installed  XML::LibXML::Common and I'm off. It looks great so far.

THanks


----- Posredoval Matja=BE Dem=B9ar/LJ-MLEK dne 29.03.2007 09:50 -----

"Scott Parris" <sp...@gr...>=20
28.03.2007 19:23

Za
<mat...@lj...>, <mon...@li...>
Kp

Zadeva
RE: [Monarch-users] Premature end of script headers error






Try running monarch=5Fajax.cgi from the command line. Also check the apache=
=20
error log. That should point you to the source of the problem.
=20

From: mon...@li...=20
[mailto:mon...@li...] On Behalf Of=20
mat...@lj...
Sent: Wednesday, March 28, 2007 1:20 AM
To: mon...@li...
Subject: [Monarch-users] Premature end of script headers error
=20

Hello!=20

I have been trying for a couple of days now to install Monarch 2.0.2 on=20
SLES9 server. Server meets all the prerequisites for Monarch,=20
monarch=5Fsetup.pl executes fine, with these parameters:=20

What is the host name of your MySQL database server? [localhost] :=20
<MYDBSERVER>=20
What is the name of the user that will have access to the database? [root] =

: monarch=20
What is the password for user monarch to access the database [] :=20
<PASSWORD>=20
What is the name of the database you will use for your Monarch=20
installation? [monarch] : monarch=20
Enter web server's user account [wwwrun] : wwwrun=20
Enter web server's user group [www] : www=20
Please enter your web servier's relative path to cgi-bin. Example:=20
/nagios/cgi-bin [ /cgi-bin ] : /cgi/bin=20
What is your web server's document root [unknown] : /srv/www=20
Enter the full path of your cgi-bin directory [unknown] : /srv/www/cgi-bin =


Enter the full installation path for Monarch=20
[/usr/local/groundwork/monarch] : /usr/local/groundwork/monarch=20
Enter the full path to your nagios.cfg file [/usr/local/nagios/etc] :=20
/usr/local/nagios/etc=20
Enter the full path to your nagios binary file [/usr/local/nagios/bin] :=20
/usr/local/nagios/bin=20
I choose to modify permissions and the setup finished with warning about=20
location of favicon.ico.=20

When I go to http://mywebserver/cgi-bin/monarch.cgi I get this:=20

Server error!=20
The server encountered an internal error and was unable to complete your=20
request.=20
Error message:=20
Premature end of script headers: monarch=5Fajax.cgi=20
If you think this is a server error, please contact the webmaster.=20
Error 500=20
Can someone please give me some usefull pointers, where to start. I=20
checked for some of common causes, that I found on the Internet, but to no =

avail.=20
Thanks in advance,=20
Mat

Re: [Monarch-users] Premature end of script headers error

[Scott P. <sp...@gr...>]

Try running monarch_ajax.cgi from the command line. Also check the
apache error log. That should point you to the source of the problem.

=20

________________________________

From: mon...@li...
[mailto:mon...@li...] On Behalf Of
mat...@lj...
Sent: Wednesday, March 28, 2007 1:20 AM
To: mon...@li...
Subject: [Monarch-users] Premature end of script headers error

=20


Hello!=20

I have been trying for a couple of days now to install Monarch 2.0.2 on
SLES9 server. Server meets all the prerequisites for Monarch,
monarch_setup.pl executes fine, with these parameters:=20

What is the host name of your MySQL database server? [localhost] :
<MYDBSERVER>=20
What is the name of the user that will have access to the database?
[root] : monarch=20
What is the password for user monarch to access the database [] :
<PASSWORD>=20
What is the name of the database you will use for your Monarch
installation? [monarch] : monarch=20
Enter web server's user account [wwwrun] : wwwrun=20
Enter web server's user group [www] : www=20
Please enter your web servier's relative path to cgi-bin. Example:
/nagios/cgi-bin [ /cgi-bin ] : /cgi/bin=20
What is your web server's document root [unknown] : /srv/www=20
Enter the full path of your cgi-bin directory [unknown] :
/srv/www/cgi-bin=20
Enter the full installation path for Monarch
[/usr/local/groundwork/monarch] : /usr/local/groundwork/monarch=20
Enter the full path to your nagios.cfg file [/usr/local/nagios/etc] :
/usr/local/nagios/etc=20
Enter the full path to your nagios binary file [/usr/local/nagios/bin] :
/usr/local/nagios/bin=20
I choose to modify permissions and the setup finished with warning about
location of favicon.ico.=20

When I go to http://mywebserver/cgi-bin/monarch.cgi I get this:=20

Server error!=20

The server encountered an internal error and was unable to complete your
request.=20

Error message:=20
Premature end of script headers: monarch_ajax.cgi=20

If you think this is a server error, please contact the webmaster
<mailto:mat...@lj...> .=20

Error 500=20

Can someone please give me some usefull pointers, where to start. I
checked for some of common causes, that I found on the Internet, but to
no avail.=20

Thanks in advance,=20

Mat

[Monarch-users] Premature end of script headers error

[<mat...@lj...>]

Hello!

I have been trying for a couple of days now to install Monarch 2.0.2 on 
SLES9 server. Server meets all the prerequisites for Monarch, 
monarch_setup.pl executes fine, with these parameters:

What is the host name of your MySQL database server? [localhost] : 
<MYDBSERVER>
What is the name of the user that will have access to the database? [root] 
: monarch
What is the password for user monarch to access the database [] : 
<PASSWORD>
What is the name of the database you will use for your Monarch 
installation? [monarch] : monarch
Enter web server's user account [wwwrun] : wwwrun
Enter web server's user group [www] : www
Please enter your web servier's relative path to cgi-bin. Example: 
/nagios/cgi-bin [ /cgi-bin ] : /cgi/bin
What is your web server's document root [unknown] : /srv/www
Enter the full path of your cgi-bin directory [unknown] : /srv/www/cgi-bin
Enter the full installation path for Monarch 
[/usr/local/groundwork/monarch] : /usr/local/groundwork/monarch
Enter the full path to your nagios.cfg file [/usr/local/nagios/etc] : 
/usr/local/nagios/etc
Enter the full path to your nagios binary file [/usr/local/nagios/bin] : 
/usr/local/nagios/bin
I choose to modify permissions and the setup finished with warning about 
location of favicon.ico.

When I go to http://mywebserver/cgi-bin/monarch.cgi I get this:

Server error!
The server encountered an internal error and was unable to complete your 
request. 
Error message: 
Premature end of script headers: monarch_ajax.cgi 
If you think this is a server error, please contact the webmaster. 
Error 500

Can someone please give me some usefull pointers, where to start. I 
checked for some of common causes, that I found on the Internet, but to no 
avail.

Thanks in advance,
Mat

Re: [Monarch-users] Status Map Ugly Now

[Don C. <Col...@or...>]

I plan on it, but I was hoping to get existing kinks worked out prior to 
upgrading but I may not have a choice.

On 12/7/06, Don Collins <Col...@or...> wrote:
>
> I have recentlly started using Groundwork Monitor Architect to maintain 
an
> existing Nagios installation. Im using GMA 1.3 with Nagios 1.2. Once i
> started using GMA it converted my host extended info config file to look
> similar to the following.
>

I agree that it should not be configuration related.  Since you've now
got your configuration imported into monarch, it really should be
trivial to upgrade nagios.  Have you thought about moving to nagios
2.6?  They've fixed a ton of bugs.


-- 
Andy Harrison

Don Collins
Sr. Unix Administrator
Orbital Sciences Corporation

-----------------------------------------
Notice:  This e-mail is intended solely for use of the individual
or entity to which it is addressed and may contain information that
is proprietary, privileged and exempt from disclosure under
applicable law.  If the reader is not the intended recipient or
agent responsible for delivering the message to the intended
recipient, you are hereby notified that any dissemination,
distribution or copying of this communication is strictly
prohibited.  This communication may also contain data subject to
U.S. export laws.  If so, that data subject to the International
Traffic in Arms Regulation cannot be disseminated, distributed or
copied to foreign nationals, residing in the U.S. or abroad, absent
the express prior approval of the U.S. Department of State.   If
you have received this communication in error, please notify the
sender by reply e-mail and destroy the e-mail message and any
physical copies made of the communication.  Thank you.

Re: [Monarch-users] Status Map Ugly Now

[Andy H. <aha...@gm...>]

On 12/7/06, Don Collins <Col...@or...> wrote:
>
> I have recentlly started using Groundwork Monitor Architect to maintain an
> existing Nagios installation. Im using GMA 1.3 with Nagios 1.2. Once i
> started using GMA it converted my host extended info config file to look
> similar to the following.
>

I agree that it should not be configuration related.  Since you've now
got your configuration imported into monarch, it really should be
trivial to upgrade nagios.  Have you thought about moving to nagios
2.6?  They've fixed a ton of bugs.


-- 
Andy Harrison

Re: [Monarch-users] Status Map Ugly Now

[Scott P. <sp...@gr...>]

That is very strange. Configuration wise there is no reason why there
would be a difference.=20

=20

  _____ =20

From: Don Collins [mailto:Col...@or...]=20
Sent: Thursday, December 07, 2006 12:01 PM
To: mon...@li...
Subject: [Monarch-users] Status Map Ugly Now

=20

  _____ =20

Notice: This e-mail is intended solely for use of the individual or
entity to which it is addressed and may contain information that is
proprietary, privileged and exempt from disclosure under applicable law.
If the reader is not the intended recipient or agent responsible for
delivering the message to the intended recipient, you are hereby
notified that any dissemination, distribution or copying of this
communication is strictly prohibited. This communication may also
contain data subject to U.S. export laws. If so, that data subject to
the International Traffic in Arms Regulation cannot be disseminated,
distributed or copied to foreign nationals, residing in the U.S. or
abroad, absent the express prior approval of the U.S. Department of
State. If you have received this communication in error, please notify
the sender by reply e-mail and destroy the e-mail message and any
physical copies made of the communication. Thank you.=20

[Monarch-users] Status Map Ugly Now

[Don C. <Col...@or...>]

I have recentlly started using Groundwork Monitor Architect to maintain an 
existing Nagios installation. Im using GMA 1.3 with Nagios 1.2. Once i 
started using GMA it converted my host extended info config file to look 
similar to the following.

define hostextinfo {
                host_name                       va-apc-3
                use                                     Black Box
                2d_coords                       3515,1090
}

define hostextinfo {
                name                                  Black Box
                icon_image                      black_box.jpg
                vrml_image                      black_box.jpg
                statusmap_image          black_box.gd2
                register                        0
}


While the above format is cleaner, there is a problem I believe with using 
it this way (at least for me.. maybe im missing something)


Previouslly I had image names for each host definition as well instead of 
making it grab em from the template, when I use the below method my images 
look good, when I use the above method my gif files etc arent showing all 
colors and look funky. The example I used here uses jpg but some of my 
definitions use gif and gd2 images that have transparency to make the map 
look pretty :) So the difference seems to be that all hosts have there 
images specified as well as what template was used. Any Ideas/suggestions 
to fix my issue?



define hostextinfo {
    use                         Black Box
    host_name                   va-apc-3
    icon_image                  black_box.jpg
    vrml_image                  black_box.jpg
    statusmap_image     black_box.gd2
    2d_coords                   3515,1090
}

define hostextinfo {
    name                Black Box
    icon_image                  black_box.jpg
    vrml_image                  black_box.jpg
    statusmap_image     black_box.gd2
    register    0
}









Don Collins
Sr. Unix Administrator
Orbital Sciences Corporation

-----------------------------------------
Notice:  This e-mail is intended solely for use of the individual
or entity to which it is addressed and may contain information that
is proprietary, privileged and exempt from disclosure under
applicable law.  If the reader is not the intended recipient or
agent responsible for delivering the message to the intended
recipient, you are hereby notified that any dissemination,
distribution or copying of this communication is strictly
prohibited.  This communication may also contain data subject to
U.S. export laws.  If so, that data subject to the International
Traffic in Arms Regulation cannot be disseminated, distributed or
copied to foreign nationals, residing in the U.S. or abroad, absent
the express prior approval of the U.S. Department of State.   If
you have received this communication in error, please notify the
sender by reply e-mail and destroy the e-mail message and any
physical copies made of the communication.  Thank you.

[Monarch-users] Problem with Version 1.3

[Ian C. <I.C...@ke...>]

Hi All,

Just upgraded our 0.97a version of Monarch to 1.3 (which looks very
nice) but have a slight problem. When trying a preflight test (or
commit) it bombs out with the error:

Error(s) building file(s): 	  	/usr/local/groundwork/monarch/workspace/
Is a directory

Looking at what is created it seems to have managed to do all the config
 files except misccommands.cfg and nagios.cfg so I'm assuming that the
code for creating one of these files is expecting the workspace
directory to be a file.

Anyone else come across this?

Ian

[Monarch-users] Removing service profile keeps services?

[Marcus F. <mf...@rh...>]

Hi List,

I'm testing monarch to rebuild my existing nagios configuration,
trying to benefit from service- and host profiles.

When i assign a /service or host) profile to a single machine, all 
services from that profile are assigned to the host. But when i remove 
the profile in the host tab or the host in the profile tab, the services 
are not removed, even though the default values have not been modified.

Is this behaviour wanted? If yes, why? IMHO this could produce database 
inconsisties, as all services of a profile are assigned to the host, but 
the profile tab doesn't display the host as a member.


Regards,

Marcus Fleige

Re: [Monarch-users] some sub routine logic errors ...

[Scott P. <sp...@gr...>]

Lido,
 
Thanks for pointing this out. I'll see that it gets addressed in the next release. Yesterday I posted monarch-1.2 on SourceForge. It is almost entirely bug fixes so it's worth installing. Also, I plan to address session management in Monarch 2.0.
 
Scott 
 
----- Original Message -----
From: mon...@li... on behalf of Lidio Presutti 
Sent: Tue, 7/11/2006 12:08pm
To: mon...@li...
Subject: [Monarch-users] some sub routine logic errors ... 
 
 
Greetings,

doing another complete clean install I noticed I was getting a whole bunch 
entries in my apache log file like:

DBD::mysql::st execute failed: Duplicate entry 'default_user_name' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
DBD::mysql::st execute failed: Duplicate entry 'show_context_help' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
DBD::mysql::st execute failed: Duplicate entry 'nagios_check_command' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
..

looking closely at MonarchStorProc.pm near that line number I see routines 
with this kind of construct:

    $sth->execute()};
    if ($@) {
        return "Error: $sqlstmt $@";
    } else {
        return 1;
    }
    $sth->finish;

The last line "$sth->finish" never gets executed due to the "return" in 
the if-else structures.  Although it is not absolutely needed to do the 
"finish" however it's always best to have "clean" code.  The fix is 
obvious.

The same applies to these other subs:

sub fetch_list_hash_array(@) {
sub fetch_all($) {
sub insert_obj(@) {
sub insert_obj_id(@) {
sub update_obj(@) {
sub update_obj_where(@) {
sub delete_all(@) {
sub delete_one_where(@) {
sub insert_dependency() {

there maybe others in other modules.

Lidio.


-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Monarch-users mailing list
Mon...@li...
https://lists.sourceforge.net/lists/listinfo/monarch-users

[Monarch-users] some sub routine logic errors ...

[Lidio P. <li...@ic...>]

Greetings,

doing another complete clean install I noticed I was getting a whole bunch 
entries in my apache log file like:

DBD::mysql::st execute failed: Duplicate entry 'default_user_name' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
DBD::mysql::st execute failed: Duplicate entry 'show_context_help' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
DBD::mysql::st execute failed: Duplicate entry 'nagios_check_command' for key 1 at /opt/local/nagios/monarch-1.0/lib/MonarchStorProc.pm line 499.
...

looking closely at MonarchStorProc.pm near that line number I see routines 
with this kind of construct:

 	$sth->execute()};
 	if ($@) {
 		return "Error: $sqlstmt $@";
 	} else {
 		return 1;
 	}
 	$sth->finish;

The last line "$sth->finish" never gets executed due to the "return" in 
the if-else structures.  Although it is not absolutely needed to do the 
"finish" however it's always best to have "clean" code.  The fix is 
obvious.

The same applies to these other subs:

sub fetch_list_hash_array(@) {
sub fetch_all($) {
sub insert_obj(@) {
sub insert_obj_id(@) {
sub update_obj(@) {
sub update_obj_where(@) {
sub delete_all(@) {
sub delete_one_where(@) {
sub insert_dependency() {

there maybe others in other modules.

Lidio.

[Monarch-users] authentication issues with monarch 1.0 and security concerns ...

[Lidio P. <li...@ic...>]

Greetings,

I just upgraded from version 0.97a to 1.0, aside from several problems 
with the monarch-upgrade.pl script I have found an authentication issue. 
The new version does not like passwords that look like "foo+bar" -- i.e. 
have a plus character in them.  The previous version did not have this 
issue.

Using Firefox Live HTTP Headers I am seeing the following:

POST /cgi-bin/monarch.cgi user_acct=super_user&password=foo%2Bbar
GET /cgi-bin/monarch.cgi?update_left=1&user_acct=super_user&top_menu=hosts&user_acct=super_user&password=foo+bar
GET /cgi-bin/monarch.cgi?update_main=1&user_acct=super_user&top_menu=hosts&user_acct=super_user&password=foo+bar

the POST is ok, I get authenticated and the screen changes to the monarch 
menu layout but it immediately throws me out to the login screen.  No 
wonder, it is not escaping the plus character in the Password.  Changing 
the password without a plus character works just fine.  That can be a work 
around.  However, unlike the previous version, a greater concern is that 
the Password is part of the GET which gets logged in the Apache log file 
in the clear.  This is very poor security.

I haven't traced out why the password field is being propagated in the 
GETs.

Lidio.

[Monarch-users] Install on Fedora Core 5

[Wiedemann, L. <LUI...@FL...>]

Hello all,

=20

I am have an issue trying to install Groundwork OS 4.5 on Fedora Core 5.
I'm not even sure it works but I thought I would give it a whirl. The
error I am getting is...

=20

Error: %pre(groundwork-monitor-os-4.5-11.i586) scriplet failed, exit
status 1

Error:     install: %pre scriptlet failed (2), skipping
groundwork-monitor-os-4.5-11

=20

Any suggestions would be wonderful!

=20

TIA

=20

Luis Wiedemann
Systems Analyst
MIS - Open Systems

RE: [Monarch-users] Problem with 1.0 -

[Adrian G. <ag...@ar...>]

To be perfectly frank, I don't think Monarch 1.0 is actually a 1.0
release.  It's so riddled with bugs that it appears that Groundwork
would like the open source community to do their debugging for them.
None of the bug reports are addressed, and there's no communication from
anyone in Groundwork.=20

I'd like access to the CVS/SVN repository so that updates can be applied
to the tree.  If Groundwork can't give that, then I'll load it into my
own repository and make that available to the community.

Adrian Goins - President / CEO
Arces Network, LLC=20
212.813.3995 v
212.813.3996 f

-----Original Message-----
From: mon...@li...
[mailto:mon...@li...] On Behalf Of
Sebastian Schubert
Sent: Tuesday, May 30, 2006 6:53 AM
To: mon...@li...
Subject: [Monarch-users] Problem with 1.0 -

Hi there,=20

i've got some trouble with the pre-flight check and commit.

after some debugging i found that the "Misccommands" are spellt
differntly:

monarc_setup.pl line 1225:

                'miscommands' =3D> 'miscommands.cfg',

MonarchFile.pm line 192:

my @types =3D \
('commands','misccommands','time_periods','contact_templates','contactgr
oups','contacts',


in version 0.96? the MonarchFile.pm spellt "miscommands" and not
"misccommands" (2 c)=20

maybe some of the developers thinks this information is useful ;)

--=20
"In god we trust, the Rest we Monitor"
Sebastian Schubert - RHCE
Stadtsparkasse Munich
Network and IT Security
--------------------------
ba...@ss...
Tel.+49 (89) 2167-6399
Fax.+49 (89) 2167-86399

[Monarch-users] Problem with 1.0 -

[Sebastian S. <ba...@ss...>]

Hi there,=20

i've got some trouble with the pre-flight check and commit.

after some debugging i found that the "Misccommands" are spellt
differntly:

monarc_setup.pl line 1225:

                'miscommands' =3D> 'miscommands.cfg',

MonarchFile.pm line 192:

my @types =3D \
('commands','misccommands','time_periods','contact_templates','contactgroup=
s','contacts',


in version 0.96? the MonarchFile.pm spellt "miscommands" and not
"misccommands" (2 c)=20

maybe some of the developers thinks this information is useful ;)

--=20
"In god we trust, the Rest we Monitor"
Sebastian Schubert - RHCE
Stadtsparkasse Munich
Network and IT Security
--------------------------
ba...@ss...
Tel.+49 (89) 2167-6399
Fax.+49 (89) 2167-86399

Re: [Monarch-users] RE: Empty checkboxes -> directives commented out

[<jo...@gm...>]

Hi, there

see http://www.groundworkopensource.com/community/forums/viewtopic.php?t=70

Greetings


Michael J. Prentice wrote:
>
> I’m having the same issue with Enable Notifications and others. With 
> them unchecked it gets output as the following, which isn’t the same 
> thing.
>
> # ENABLE NOTIFICATIONS
>
> # enable_notifications=
>
> From: <joh_m@gm...>
> Empty checkboxes -> directives commented out 
> <http://sourceforge.net/mailarchive/message.php?msg_id=15299194>
> 2006-04-04 01:33
>
> Hi there,
>  
> we want to use Nagios with Monarch in our company.
> Our goal is to use mod_auth_ldap for authenticaton on the web frontends.
> Therefore we have to disable the internal authentication mechanisms of
> Nagios and Monarch.
>  
> Now to the problem.
> Under "Control" -> "Nagios Cgi Configuration" -> "View Edit" we uncheck "Use
> authentication" to disable Nagios internal authentication.
> Then we run "Commit" and there something goes wrong.
> The function that generates the Nagios cgi.cfg comments out the
> use_authentication directive. This forces Nagios to use its default value,
> which is "1".
> As you see, we cannot disable Nagios authentication through Monarch, which
> leads us to manually reconfigure the cgi.cfg file.
>  
> Btw. i'm sure this also affects other directives that are controlled by
> checkboxes and are !=0 by default.
> Is there any chance of a fix?
>  
> -- 
> "Feel free" - 10 GB Mailbox, 100 FreeSMS/Monat ...
> Jetzt GMX TopMail testen: http://www.gmx.net/de/go/topmail
>

[Monarch-users] Losing contact group

[Andy F. <And...@ad...>]

Hi,

I'm using Nagios 1.3 and Monarch 0.97a, and I'm getting frustrated with 
a minor problem.

When I clone a host, I still have to go into each service for that host 
and specify a contact group, it doesn't seem to be carried forward from 
the host I'm cloning. Is this an issue with my templates or something 
that should be done within Monarch ?

Any thoughts ?

Andy

-- 
Andy Fry

Senior Systems Consultant
Information Technology Services
University of Adelaide
Tel : 08 8303 4135

CRICOS Provider Number 00123M
----------------------------------------------------------- 
This email message is intended only for the addressee(s) 
and contains information that may be confidential and/or 
copyright.  If you are not the intended recipient please 
notify the sender by reply email and immediately delete 
this email. Use, disclosure or reproduction of this email 
by anyone other than the intended recipient(s) is strictly 
prohibited. No representation is made that this email or 
any attachments are free of viruses. Virus scanning is 
recommended and is the responsibility of the recipient.

RE: [Monarch-users] (no subject)

[List R. <lis...@ma...>]

That fixed her right up.  Thanks Scott.
=20

-----Original Message-----
From: Scott Parris [mailto:sp...@gr...]=20
Sent: Wednesday, April 05, 2006 11:16 AM
To: List Receiver; mon...@li...
Subject: RE: [Monarch-users] (no subject)

Comment out line 1155. It appears that the table was properly populated
during the previous run and it's trying to repopulate it (hence
duplicate entry).  =20
 =20
----- Original Message -----
From: List Receiver
Sent: Tue Apr 4 21:45:04 PDT 2006
To: Scott Parris ; mon...@li...
Subject: RE: [Monarch-users] (no subject)
 =20
 =20
Any thoughts on this error yet?  This is the output I get when I re-run
monarch_update.pl:=20

        Writing /srv/www/cgi-bin/monarch_ajax.cgi=20
        Updating setup information...=20

        Checking tables...=20
DBD::mysql::db do failed: Duplicate entry '7-22' for key 1 at
monarch_update.pl line 1155.=20
DBD::mysql::db do failed: Duplicate entry '7-22' for key 1 at
monarch_update.pl line 1155.=20



-----Original Message-----
From: Scott Parris [mailto:sp...@gr...]
Sent: Saturday, April 01, 2006 1:50 PM
To: List Receiver
Subject: RE: [Monarch-users] (no subject)=20

It does appear that something didn't go well during the update. A column
should have been removed from the hosts table for starters. The first
thing to try is rerun monarch_update.pl. There should be some errors if
it doesn't go right.=20
  =20
Scott    =20
  =20
----- Original Message -----
From: List Receiver
Sent: Fri Mar 31 23:33:50 PST 2006
To: mon...@li...
Subject: [Monarch-users] (no subject)=20
  =20
  =20
I've got a few issues with Monarch 1.0 following an upgrade from .97a.=20

1) Commit or pre-flight show blank screens where they should output=20
error messages and stats=20
2) Cloning or adding a new host generates LOADS of sql errors like this:



Error: insert into hosts=20
values(NULL,'fartyjowels','asdf','1.2.3.4',NULL,NULL,NULL,'9',NULL,NULL,

'1',NULL) DBD::mysql::st execute failed: Column count doesn't match=20
value count at row 1 at=20
/usr/local/groundwork/monarch/lib/MonarchStorProc.pm line 523.=20

3) Running commit does not move any of the generated config files from=20
the workspace to /usr/local/nagios/etc.  I can manually move them, and=20
nagios runs, but they're not moved automatically=20

Seems to be some horrendous steps backward in comparison to .97a...I=20
must have botched the install somehow???=20

Any ideas where to start?=20


-------------------------------------------------------=20
This SF.Net email is sponsored by xPML, a groundbreaking scripting=20
language that extends applications into web and mobile media. Attend the

live webcast and join the prime developer group breaking into this new=20
coding territory!=20
http://sel.as-us.falkag.net/sel?cmdblnk&kid 0944&bid$1720&dat 1642=20
_______________________________________________=20
Monarch-users mailing list=20
Mon...@li...=20
https://lists.sourceforge.net/lists/listinfo/monarch-users=20

RE: [Monarch-users] (no subject)

[Scott P. <sp...@gr...>]

Comment out line 1155. It appears that the table was properly populated during the previous run and it's trying to repopulate it (hence duplicate entry).   
  
----- Original Message ----- 
From: List Receiver 
Sent: Tue Apr 4 21:45:04 PDT 2006 
To: Scott Parris ; mon...@li... 
Subject: RE: [Monarch-users] (no subject)
  
  
Any thoughts on this error yet?  This is the output I get when I re-run 
monarch_update.pl: 

        Writing /srv/www/cgi-bin/monarch_ajax.cgi 
        Updating setup information... 

        Checking tables... 
DBD::mysql::db do failed: Duplicate entry '7-22' for key 1 at 
monarch_update.pl line 1155. 
DBD::mysql::db do failed: Duplicate entry '7-22' for key 1 at 
monarch_update.pl line 1155. 



-----Original Message----- 
From: Scott Parris [mailto:sp...@gr...] 
Sent: Saturday, April 01, 2006 1:50 PM 
To: List Receiver 
Subject: RE: [Monarch-users] (no subject) 

It does appear that something didn't go well during the update. A column 
should have been removed from the hosts table for starters. The first 
thing to try is rerun monarch_update.pl. There should be some errors if 
it doesn't go right. 
   
Scott     
   
----- Original Message ----- 
From: List Receiver 
Sent: Fri Mar 31 23:33:50 PST 2006 
To: mon...@li... 
Subject: [Monarch-users] (no subject) 
   
   
I've got a few issues with Monarch 1.0 following an upgrade from .97a. 

1) Commit or pre-flight show blank screens where they should output 
error messages and stats 
2) Cloning or adding a new host generates LOADS of sql errors like this: 


Error: insert into hosts 
values(NULL,'fartyjowels','asdf','1.2.3.4',NULL,NULL,NULL,'9',NULL,NULL, 
'1',NULL) DBD::mysql::st execute failed: Column count doesn't match 
value count at row 1 at 
/usr/local/groundwork/monarch/lib/MonarchStorProc.pm line 523. 

3) Running commit does not move any of the generated config files from 
the workspace to /usr/local/nagios/etc.  I can manually move them, and 
nagios runs, but they're not moved automatically 

Seems to be some horrendous steps backward in comparison to .97a...I 
must have botched the install somehow??? 

Any ideas where to start? 


------------------------------------------------------- 
This SF.Net email is sponsored by xPML, a groundbreaking scripting 
language that extends applications into web and mobile media. Attend the 
live webcast and join the prime developer group breaking into this new 
coding territory! 
http://sel.as-us.falkag.net/sel?cmdblnk&kid 0944&bid$1720&dat 1642 
_______________________________________________ 
Monarch-users mailing list 
Mon...@li... 
https://lists.sourceforge.net/lists/listinfo/monarch-users