Hi,
I am wanting to utilise the WOL facilty to switch my PC on remotely when away
from home.
I have flashed my DGN2200 router with the modified firmware and loaded the
image on a USB and everything works fine internally on the LAN.
I have set up a port forward rule to send port 8081 to IP address 192.168.0.2
(outside of DHCP allocated addresses).
My problem is that when I try to access my router from the internet using my
dnslias account
(http://xxx.dnsalias.com:8081) the port
8081 is not seen. I have checked the port using canyouseeme.org and it doesnt
appear to be open.
How can i open the port to allow me to access the modfs web admin page?
Many Thanks,
Bowz
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
I'm also trying to access this remotely. I've setup as port forwarding as
indicated above but i can't see any pages with 'Additional LAN IP Address' to
set. Could you give me a pointer to where they are?. Everything works ok over
LAN but not over internet. I'm using a DGN3500
Thanks
millsy
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi cmillsy,
on dgn3500 you haven't to add an additional ip, but you have only to go to
Nat/QoS menu and add a port forward rule to your router ip.
To access remotely through https,
First be sure to start portfoward and https as in this screen: http://imageshack.us/photo/my-
images/406/gui1v.png/
then go Nat/Qos menu and set a rule like this http://imageshack.us/photo/my-
images/29/gui2f.png/
not firm gui but modfs gui rule, then click on save and on apply
And you are able to access remotely through: https://youinternetip:4443
Best Regards.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
I am wanting to utilise the WOL facilty to switch my PC on remotely when away
from home.
I have flashed my DGN2200 router with the modified firmware and loaded the
image on a USB and everything works fine internally on the LAN.
I have set up a port forward rule to send port 8081 to IP address 192.168.0.2
(outside of DHCP allocated addresses).
My problem is that when I try to access my router from the internet using my
dnslias account
(http://xxx.dnsalias.com:8081) the port
8081 is not seen. I have checked the port using canyouseeme.org and it doesnt
appear to be open.
How can i open the port to allow me to access the modfs web admin page?
Many Thanks,
Bowz
You have to specify 192.168.0.2 as "Additional LAN IP Address" on Setup/Main
page
Hi,
I'm also trying to access this remotely. I've setup as port forwarding as
indicated above but i can't see any pages with 'Additional LAN IP Address' to
set. Could you give me a pointer to where they are?. Everything works ok over
LAN but not over internet. I'm using a DGN3500
Thanks
millsy
Hi cmillsy,
on dgn3500 you haven't to add an additional ip, but you have only to go to
Nat/QoS menu and add a port forward rule to your router ip.
To access remotely through https,
First be sure to start portfoward and https as in this screen:
http://imageshack.us/photo/my-
images/406/gui1v.png/
then go Nat/Qos menu and set a rule like this
http://imageshack.us/photo/my-
images/29/gui2f.png/
not firm gui but modfs gui rule, then click on save and on apply
And you are able to access remotely through:
https://youinternetip:4443
Best Regards.
Excellent! that worked. Thanks gnommo.