## Re: [misterhouse-users] Weather_wmr968.pm question

 Re: [misterhouse-users] Weather_wmr968.pm question From: Dominique Benoliel - 2004-11-24 21:21:37 ```The comments in "Weather_wmr968.pm" script are not correct. Look at the comments in "mh/code/common/weather_rrd_update.pl" script. These parameters impact only the weather graphs but not the units of the \$Weather{..} variables. # weather_uom_temp = C (C, F) # weather_uom_baro = in (mb, in) # weather_uom_wind = mph (m/s, mph, kph) # weather_uom_rain = in (mm, in) # weather_uom_rainrate = in/hr (mm/hr, in/hr) Best Regards. Dominique. ```

 [misterhouse-users] control more than x10 unit codes on Slimline Switches From: WK - 2004-11-23 18:18:23 ```I have a Slimline Switch can control which can up to 3 x10 unit codes. Can I control more than 3 x10 unit codes using the slimline switch together with misterhouse? Let's assume that the slimline switch can control C1, C2, and C3 x10 unit code. If C1-On is pressed twice within x seconds, it turns on light_1 If C2-On is pressed twice, it turns on light_2 If C3-On is pressed twice, it turns on light_3 If C1-On and C2-On is pressed, it turns on light_4 If C1-On and C3-On is pressed, it turns on light_5 etc .... If yes, is there any example that I can refer to? Thx, Wooi. ```
 Re: [misterhouse-users] control more than x10 unit codes on Slimline Switches From: Chris Barrett - 2004-11-23 20:28:58 ```I've used these switches to control 6 devices. set L1 TOGGLE if state_now C1 eq ON; set L2 TOGGLE if state_now C1 eq OFF; set L3 TOGGLE if state_now C2 eq ON; set L4 TOGGLE if state_now C2 eq OFF; set L5 TOGGLE if state_now C3 eq ON; set L6 TOGGLE if state_now C3 eq OFF; The danger with these switches is that multiple keypresses of the top button could place it into the mode that allows you to change the house and unit codes. One switch in particular here was often getting accidentally reset to "A1". ----- Original Message ----- From: "WK" To: Sent: Wednesday, November 24, 2004 5:18 AM Subject: [misterhouse-users] control more than x10 unit codes on Slimline Switches >I have a Slimline Switch can control which can up to 3 x10 unit codes. Can >I control more than 3 x10 unit codes using the slimline switch together >with misterhouse? > > Let's assume that the slimline switch can control C1, C2, and C3 x10 unit > code. > > If C1-On is pressed twice within x seconds, it turns on light_1 > If C2-On is pressed twice, it turns on light_2 > If C3-On is pressed twice, it turns on light_3 > If C1-On and C2-On is pressed, it turns on light_4 > If C1-On and C3-On is pressed, it turns on light_5 > etc .... > > If yes, is there any example that I can refer to? > > Thx, > Wooi. ```
 [misterhouse-users] Weather_wmr968.pm question From: Michel van Osenbruggen - 2004-11-24 00:19:59 ```Hi, I found these mh.ini parameters in de comment of Weather=5Fwmr968.pm: default=5Fuom=5Ftemp =3D 0 # 0=3DC, 1=3DF default=5Fuom=5Fbaro =3D 0 # 0=3Dmb, 1=3DinHg default=5Fuom=5Fwind =3D 1 # 0=3Dmph, 1=3Dkph default=5Fuom=5Frain =3D 0 # 0=3Dmm, 1=3Din default=5Fuom=5Frainrate =3D 1 # 0=3Dmm/hr, 1=3Din/hr Am I using them correctly=3F It doesn't work for me anyway. Any tips=3F = Offcouse I would like to use Metric values. --=20 Yours sincerely, Michel van Osenbruggen ```
 Re: [misterhouse-users] Weather_wmr968.pm question From: Chris Barrett - 2004-11-24 07:20:51 ```I don't use this module so I can't help you out. However it would seem to me to make sense to swap the order of default_uom_wind so that the metric units are 0 and the imperial units are 1 for consistency with the other 5. ----- Original Message ----- From: "Michel van Osenbruggen" To: Sent: Wednesday, November 24, 2004 11:23 AM Subject: [misterhouse-users] Weather_wmr968.pm question Hi, I found these mh.ini parameters in de comment of Weather_wmr968.pm: default_uom_temp = 0 # 0=C, 1=F default_uom_baro = 0 # 0=mb, 1=inHg default_uom_wind = 1 # 0=mph, 1=kph default_uom_rain = 0 # 0=mm, 1=in default_uom_rainrate = 1 # 0=mm/hr, 1=in/hr Am I using them correctly? It doesn't work for me anyway. Any tips? Offcouse I would like to use Metric values. -- Yours sincerely, Michel van Osenbruggen ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://productguide.itmanagersjournal.com/ ________________________________________________________ To unsubscribe from this list, go to: http://sourceforge.net/mail/?group_id65 ```
 Re: [misterhouse-users] Weather_wmr968.pm question From: Dominique Benoliel - 2004-11-24 21:21:37 ```The comments in "Weather_wmr968.pm" script are not correct. Look at the comments in "mh/code/common/weather_rrd_update.pl" script. These parameters impact only the weather graphs but not the units of the \$Weather{..} variables. # weather_uom_temp = C (C, F) # weather_uom_baro = in (mb, in) # weather_uom_wind = mph (m/s, mph, kph) # weather_uom_rain = in (mm, in) # weather_uom_rainrate = in/hr (mm/hr, in/hr) Best Regards. Dominique. ```