The problem I have is that I'm not able to connect.
When scanning for the cube, 'trace' tells me that cube is found but in 'overview' i don't see it.
When scanning for the host I get this error:
Lan discovery error [10049] Cannot assign requested address, when binding the socket to 192.168.1.1:23272
I really look forward having your SW working!
Thanks
Max
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
This error means that the software tries to scan the LAN assuming that address of the PC is 192.168.1.1. This is obviously not so. An address likey this is more likely the address of your router, which normally has the first address of the LAN segment: x.x.x.1.
By default the PC address is obtained from the OS. It is possibly that you have a network configuration problem.
fix you PC network settings, if the address is reported incorrectly, or
you can tell explicitly which address to use. On the settings pane there is the field "Host address" for that. Possibly you have it set to 192.168.1.1? Then that is your problem. Clear it up in order to let the program to use the address from the PC network configuration, or
you can set the cube IP address directly and turn LAN discovery off. On the settings pane there is a field for that.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Dear Dmitry, right! Actually it works well, even if sometimes if fails loading properly, and I haven't got why... I'll try now to set up the ODBC connection to trace all data
Thanks a lot, good work!!!
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
The issue is fixed by adding one device to cube gateway by using the official software.
Then your software is able to connect to the cube permanently ans show the room device as a child object.
So maybe no need to deal with the reported issue further.
Regards
Tamás
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Right. The M-response contains the list of rooms and devices. When the cube is not yet configured the response is empty. Presently it is impossible to configure the cube without the official software.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Bonjour,
Lors du lancement de l'application Max home automation, l'application ne trouve aucun cube, je dois rentrer l'adresse ip manuellement. Cela pose un problème quand je lance l'application a distance en SSH avec un environnement graphique virtuel, avez vous une solution pour qu'il scanne correctement le réseau?
D'avance merci.
Cordialement.
Good morning,
When launching the Max home automation application, the application does not find any cube, I have to enter the IP address manually. This poses a problem when I launch the application remotely via SSH with a virtual graphical environment. Do you have a solution so that it scans the network correctly?
Thanks.
Sincerely.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Usually the issue is fixed by rebooting the cube. Turn the power off. Wait 15 seconds. Plug the cube back. When you start MAX! home automation application again it will find the cube.
P.S. Note that cube discovery works only in the same LAN segment.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Questa email è stata esaminata alla ricerca di virus da AVG.
http://www.avg.com
Dear Dmitry,
sorry for empty mail...
The problem I have is that I'm not able to connect.
When scanning for the cube, 'trace' tells me that cube is found but in 'overview' i don't see it.
When scanning for the host I get this error:
Lan discovery error
[10049] Cannot assign requested address, when binding the socket to 192.168.1.1:23272
I really look forward having your SW working!
Thanks
Max
This error means that the software tries to scan the LAN assuming that address of the PC is 192.168.1.1. This is obviously not so. An address likey this is more likely the address of your router, which normally has the first address of the LAN segment: x.x.x.1.
By default the PC address is obtained from the OS. It is possibly that you have a network configuration problem.
Dear Dmitry, right! Actually it works well, even if sometimes if fails loading properly, and I haven't got why... I'll try now to set up the ODBC connection to trace all data
Thanks a lot, good work!!!
Hello Dmitry,
I have a brandnew MAX CUBE and on the trace I can see repeated connected/disconnected message with "Invalid M-response, missing first field"
Do you have an idea what I am doing wrong?
I can see any specific characters "%0D%0A" at the end of "H:" that is listed in "M:" but the leading 0000 was cut somehow or no relation at all.
2019-01-27 23:38:26.84 172.16.73.252 NEQ1634468H:NEQ1634468,175447,0113,00000000,5f867fef,00,32,0b0101,0819,00,0000%0D%0A
2019-01-27 23:38:26.06 172.16.73.252 NEQ1634468M:%0D%0AC:175447,7RdURwATAf9ORVExNjM0NDY4AAsABEAAAAAAAAAAAP///////////////////////////wsABEAAAAAAAAAAQf///////////////////////////2h0dH
It looks like it is considered as invalid message...
Shall I do first any kind of intial setup with the offical software to change that parameter?
Here is the repeated messages:
MAX! cube at 172.16.73.252 eQ3MaxAp NEQ1634468 reading 172.16.73.252:62910 2019-01-27 23:38:26.84 172.16.73.252 NEQ1634468H:NEQ1634468,175447,0113,00000000,5f867fef,00,32,0b0101,0819,00,0000%0D%0A 172.16.73.252 NEQ1634468 eQ3MaxAp Connected reading 172.16.73.252:62910 2019-01-27 23:38:26.06 172.16.73.252 NEQ1634468M:%0D%0AC:175447,7RdURwATAf9ORVExNjM0NDY4AAsABEAAAAAAAAAAAP///////////////////////////wsABEAAAAAAAAAAQf///////////////////////////2h0dH Processing received fault: raised ADA.IO_EXCEPTIONS.DATA_ERROR : Invalid M-response, missing first field 172.16.73.252 NEQ1634468 eQ3MaxAp disconnectedThanks
&
Regards
Tamás
Hello Dmitry,
The issue is fixed by adding one device to cube gateway by using the official software.
Then your software is able to connect to the cube permanently ans show the room device as a child object.
So maybe no need to deal with the reported issue further.
Regards
Tamás
Right. The M-response contains the list of rooms and devices. When the cube is not yet configured the response is empty. Presently it is impossible to configure the cube without the official software.
Bonjour,
Lors du lancement de l'application Max home automation, l'application ne trouve aucun cube, je dois rentrer l'adresse ip manuellement. Cela pose un problème quand je lance l'application a distance en SSH avec un environnement graphique virtuel, avez vous une solution pour qu'il scanne correctement le réseau?
D'avance merci.
Cordialement.
Good morning,
When launching the Max home automation application, the application does not find any cube, I have to enter the IP address manually. This poses a problem when I launch the application remotely via SSH with a virtual graphical environment. Do you have a solution so that it scans the network correctly?
Thanks.
Sincerely.
Usually the issue is fixed by rebooting the cube. Turn the power off. Wait 15 seconds. Plug the cube back. When you start MAX! home automation application again it will find the cube.
P.S. Note that cube discovery works only in the same LAN segment.
ca fonctionne, merci !😁
it works, thank you!