Thread: Re: [Madwifi-devel] Beacons not getting emitted
Status: Beta
Brought to you by:
otaku
From: Dino J. M. <din...@ya...> - 2009-07-30 05:48:00
Attachments:
beacon-debug.txt
|
Hi, attached the log message when athdebug 0x8080(beacon and beacon_proc) enabled Regards, Dino Joseph Mycle --- On Tue, 28/7/09, Dino Joseph Mycle <din...@ya...> wrote: > From: Dino Joseph Mycle <din...@ya...> > Subject: [Madwifi-devel] Beacons not getting emitted > To: mad...@li... > Date: Tuesday, 28 July, 2009, 6:32 PM > Hi , > In trunk r4079 and previous > versions(openhal) beacons frames(AP mode) > are not getting emitted.. If you scan with a PC it will > show because > it uses active scanning(Probe request/response). > > Using netstumbler you wont be able to see the ssid. > > My PC config : kernel 2.6.18-92.el5 (CentOS) > wlan: mac acl policy registered > PCI: Enabling device 0000:02:02.0 (0210 -> 0212) > ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 17 (level, > low) -> IRQ 169 > MadWifi: ath_attach: Switching rfkill capability off. > wifi0: Atheros AR5413 chip found (MAC 10.4, PHY SChip 6.1, > Radio 6.3) > ath_pci: wifi0: Atheros 5413: mem=0x50000000, irq=169 > > I tried debugging the athdebug beacon, no printk coming. > > > Regards, > Dino Joseph Mycle > Looking for local information? Find it on Yahoo! Local http://in.local.yahoo.com/ |
From: Dino J. M. <din...@ya...> - 2009-09-16 05:57:21
Attachments:
cap01.png
|
--- On Wed, 16/9/09, Pavel Roskin <pr...@gn...> wrote: > anyone noticed this. > > I had tested with spectrum analyser, there is no > signal coming. > > Sorry for delay. I cannot reproduce the problem with > any card I have. > I see the beacons in Wireshark on another system. > Running "athdebug > 0x8080" doesn't stop the beacons. > > -- > Regards, > Pavel Roskin > Hi pavel, attached the wireshark capture png file (cap01.png) , there is no beacon emitted, i also checked with spectrum analyzer. i am using one IXP based platform with compex miniPCI(AR5414). same miniPCI with openwrt is emitting beacons. openwrt uses madwifi r3314(with patches) only probe response are coming. regards dino Connect more, do more and share more with Yahoo! India Mail. Learn more. http://in.overview.mail.yahoo.com/ |
From: Pavel R. <pr...@gn...> - 2009-09-17 06:03:27
|
On Tue, 2009-09-15 at 22:57 -0700, Dino Joseph Mycle wrote: > attached the wireshark capture png file (cap01.png) , there is no > beacon emitted, i also checked with spectrum analyzer. I don't doubt you report, I just could not reproduce with the current trunk. > i am using one IXP based platform with compex miniPCI(AR5414). same > miniPCI with openwrt is emitting beacons. openwrt uses madwifi > r3314(with patches) > only probe response are coming. Then obviously the patches are the suspect. -- Regards, Pavel Roskin |
From: Dino J. M. <din...@ya...> - 2009-09-17 08:02:27
|
hi pavel, can you tell me your hardware details. are you using soc boards or miniPCI based cards ? Regards, Dino Joseph Mycle --- On Thu, 17/9/09, Pavel Roskin <pr...@gn...> wrote: > From: Pavel Roskin <pr...@gn...> > Subject: Re: [Madwifi-devel] Beacons not getting emitted > To: "Dino Joseph Mycle" <din...@ya...> > Cc: mad...@li... > Date: Thursday, 17 September, 2009, 11:33 AM > On Tue, 2009-09-15 at 22:57 -0700, > Dino Joseph Mycle wrote: > > > attached the wireshark capture png > file (cap01.png) , there is no > > beacon emitted, i also checked with spectrum > analyzer. > > I don't doubt you report, I just could not reproduce with > the current > trunk. > > > i am using one IXP based platform with compex > miniPCI(AR5414). same > > miniPCI with openwrt is emitting beacons. openwrt uses > madwifi > > r3314(with patches) > > only probe response are coming. > > Then obviously the patches are the suspect. > > -- > Regards, > Pavel Roskin > Now, send attachments up to 25MB with Yahoo! India Mail. Learn how. http://in.overview.mail.yahoo.com/photos |
From: Pavel R. <pr...@gn...> - 2009-09-19 04:12:12
|
On Thu, 2009-09-17 at 01:02 -0700, Dino Joseph Mycle wrote: > hi pavel, > can you tell me your hardware details. are you using soc boards or miniPCI based cards ? I tested miniPCI cards as well as several different CardBus cards. -- Regards, Pavel Roskin |
From: Derek S. <de...@in...> - 2009-09-19 07:07:07
|
Hi, It could be the startup script, and or the speed of the box. (1)Can I suggest that the relevant commands from the startup script used by Dino get posted, and then others can try them commands. To see if it is the speed of the box, the script described in (1) get altered to have a 1 second sleep between each command. This "sleepy" variant should work as well as the non sleepy variant.. Derek. On Sat, 19 Sep 2009, Pavel Roskin wrote: > On Thu, 2009-09-17 at 01:02 -0700, Dino Joseph Mycle wrote: >> hi pavel, >> can you tell me your hardware details. are you using soc boards or miniPCI based cards ? > > I tested miniPCI cards as well as several different CardBus cards. > > -- Derek Smithies Ph.D. IndraNet Technologies Ltd. Email: de...@in... ph +64 3 365 6485 Web: http://www.indranet-technologies.com/ |
From: Dino J. M. <din...@ya...> - 2009-09-23 05:28:22
|
Derek, I am testing it in IXP425 with 533MHz speed. I Also tried in my PC. Below is the script i tried with and without sleep after every line below wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid Test iwconfig ath0 freq 165 iwconfig ath0 rate auto brctl addbr br0 brctl setfd br0 1 brctl addif br0 ath0 brctl addif br0 eth0 ifconfig eth0 0.0.0.0 up ifconfig ath0 0.0.0.0 up ifconfig br0 192.168.1.20 up Regards, Dino Joseph Mycle --- On Sat, 19/9/09, Derek Smithies <de...@in...> wrote: > From: Derek Smithies <de...@in...> > Subject: Re: [Madwifi-devel] Beacons not getting emitted > To: "Pavel Roskin" <pr...@gn...> > Cc: "Dino Joseph Mycle" <din...@ya...>, mad...@li... > Date: Saturday, 19 September, 2009, 12:36 PM > Hi, > It could be the startup script, and or the speed of the > box. > > (1)Can I suggest that the relevant commands from the > startup script used > by Dino get posted, and then others can > try them commands. > > To see if it is the speed of the box, the script described > in (1) get altered to have a 1 second sleep between each > command. This "sleepy" variant should work as well as the > non sleepy variant.. > > Derek. > > Yahoo! India has a new look. Take a sneak peek http://in.yahoo.com/trynew |
From: Dino J. M. <din...@ya...> - 2009-09-23 06:03:41
|
Hi derek One thing forgot to tell, if i do ifconfig ath0 down then ifconfig ath0 up for 4 times, beacons start emitting. Regards, Dino Joseph Mycle --- On Wed, 23/9/09, Dino Joseph Mycle <din...@ya...> wrote: > From: Dino Joseph Mycle <din...@ya...> > Subject: Re: [Madwifi-devel] Beacons not getting emitted > To: "Pavel Roskin" <pr...@gn...>, "Derek Smithies" <de...@in...> > Cc: mad...@li... > Date: Wednesday, 23 September, 2009, 10:58 AM > Derek, > I am testing it in IXP425 with 533MHz > speed. I Also tried in my PC. > > Below is the script i tried with and without sleep after > every line below > > wlanconfig ath0 create wlandev wifi0 wlanmode ap > iwconfig ath0 essid Test > iwconfig ath0 freq 165 > iwconfig ath0 rate auto > > brctl addbr br0 > brctl setfd br0 1 > brctl addif br0 ath0 > brctl addif br0 eth0 > > ifconfig eth0 0.0.0.0 up > ifconfig ath0 0.0.0.0 up > > ifconfig br0 192.168.1.20 up > > Regards, > Dino Joseph Mycle > > > --- On Sat, 19/9/09, Derek Smithies <de...@in...> > wrote: > > > From: Derek Smithies <de...@in...> > > Subject: Re: [Madwifi-devel] Beacons not getting > emitted > > To: "Pavel Roskin" <pr...@gn...> > > Cc: "Dino Joseph Mycle" <din...@ya...>, > mad...@li... > > Date: Saturday, 19 September, 2009, 12:36 PM > > Hi, > > It could be the startup script, and or the speed > of the > > box. > > > > (1)Can I suggest that the relevant commands from the > > startup script used > > by Dino get posted, and then others can > > try them commands. > > > > To see if it is the speed of the box, the script > described > > in (1) get altered to have a 1 second sleep between > each > > command. This "sleepy" variant should work as well as > the > > non sleepy variant.. > > > > Derek. > > Yahoo! India has a new look. Take a sneak peek http://in.yahoo.com/trynew |
From: Dino <din...@ya...> - 2009-08-07 03:09:44
|
Dino Joseph Mycle <dinomycle <at> yahoo.com> writes: > > Hi, > attached the log message when athdebug 0x8080(beacon and beacon_proc) enabled > > Regards, > Dino Joseph Mycle hi, any udpate on the issue. does anyone noticed this. I had tested with spectrum analyser, there is no signal coming. Thanks and regards dino |
From: Pavel R. <pr...@gn...> - 2009-09-16 02:44:58
|
On Fri, 2009-08-07 at 03:09 +0000, Dino wrote: > Dino Joseph Mycle <dinomycle <at> yahoo.com> writes: > > > > > Hi, > > attached the log message when athdebug 0x8080(beacon and > beacon_proc) enabled > > > > Regards, > > Dino Joseph Mycle > > hi, > any udpate on the issue. does anyone noticed this. > I had tested with spectrum analyser, there is no signal coming. Sorry for delay. I cannot reproduce the problem with any card I have. I see the beacons in Wireshark on another system. Running "athdebug 0x8080" doesn't stop the beacons. -- Regards, Pavel Roskin |