lirc - Send doesn't work e.g. ir-ctl -stv.ir

[Mariusz F. <mf...@fa...>]

I am using:

IR Receiver + Wire - Iduino SE027

IR 940nm Transmitter + Wire - Iduino SE028


I can record:

ir-ctl -rtv.ir -d /dev/lirc1

cat tv.ir
+4541 -4401 +603 -1622 +623 -1631 +617 -1621 +629 -494 +623 -505 +623 
-506 +622 -505 +624 -504 +627 -1620 +621 -1623 +629 -1630 +606 -507 +632 
-495 +621 -504 +623 -505 +625 -504 +622 -505 +624 -1639 +634 -480 +622 
-503 +649 -481 +622 -506 +621 -506 +623 -505 +649 -1601 +624 -500 +649 
-1600 +617 -1625 +621 -1627 +619 -1623 +632 -1619 +613 -1623 +646 -24922
+4519 -4404 +615 -1624 +618 -1626 +644 -1601 +647 -479 +648 -481 +654 
-476 +621 -504 +624 -505 +647 -1600 +647 -1599 +622 -1624 +627 -510 +646 
-480 +645 -491 +606 -508 +620 -502 +649 -477 +626 -1625 +627 -493 +652 
-481 +642 -486 +630 -496 +645 -475 +622 -503 +622 -1626 +645 -482 +623 
-1635 +634 -1600 +618 -1625 +620 -1625 +640 -1606 +631 -1617 +647 -27229
+4532 -4394 +641 -1607 +610 -1626 +622 -1626 +643 -481 +647 -480 +621 
-514 +646 -474 +647 -490 +642 -1598 +642 -1600 +643 -1601 +644 -481 +647 
-483 +657 -470 +644 -482 +648 -482 +644 -482 +647 -1601 +619 -507 +647 
-481 +648 -479 +627 -502 +643 -483 +644 -485 +643 -1603 +646 -482 +645 
-1601 +642 -1613 +616 -1620 +645 -1599 +642 -1604 +642 -1603 +655 -19502
+4556 -4370 +641 -1605 +642 -1605 +638 -1602 +643 -484 +644 -485 +645 
-484 +642 -484 +644 -483 +643 -1614 +639 -1596 +639 -1607 +639 -484 +643 
-485 +643 -484 +644 -485 +656 -472 +643 -487 +642 -1603 +647 -488 +635 
-483 +644 -483 +642 -485 +643 -488 +652 -474 +643 -1604 +642 -484 +642 
-1605 +641 -1607 +640 -1615 +636 -1594 +641 -1623 +626 -1601 +640 -21768



but when I execute:

ir-ctl -stv.ir
warning: tv.ir:4: trailing space ignored


I see that IR is working (Iduino SE028 has LED and using my mobile 
camera), but TV is not switching ON.

My config:

ir-ctl -f -d /dev/lirc0
Receive features /dev/lirc0:
  - Device cannot receive
Send features /dev/lirc0:
  - Device can send raw IR
  - IR scancode encoder
  - Set carrier
  - Set duty cycle


ir-ctl -f -d /dev/lirc1
Receive features /dev/lirc1:
  - Device can receive raw IR
  - Can report decoded scancodes and protocol
  - Receiving timeout 12664 microseconds
  - Can set receiving timeout min 1 microseconds, max 1250000 microseconds
Send features /dev/lirc1:
  - Device cannot send


cat /boot/firmware/config.txt
# For more options and information see
# http://rptl.io/configtxt
# Some settings may impact device functionality. See link above for details

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

# Additional overlays and parameters are documented
# /boot/firmware/overlays/README

# Automatically load overlays for detected cameras
camera_auto_detect=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Automatically load initramfs files, if found
auto_initramfs=1

# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2

# Don't have the firmware create an initial video= setting in cmdline.txt.
# Use the kernel's default instead.
disable_fw_kms_setup=1

# Disable compensation for displays with overscan
disable_overscan=1

# Run as fast as firmware / board allows
arm_boost=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[cm5]
dtoverlay=dwc2,dr_mode=host

[all]
dtoverlay=gpio-ir,gpio_pin=27
dtoverlay=gpio-ir-tx,gpio_pin=22


cat /etc/lirc/lirc_options.conf
# These are the default options to lircd, if installed as
# /etc/lirc/lirc_options.conf. See the lircd(8) and lircmd(8)
# manpages for info on the different options.
#
# Some tools including mode2 and irw uses values such as
# driver, device, plugindir and loglevel as fallback values
# in not defined elsewhere.

[lircd]
nodaemon        = False
driver          = devinput
device          = auto
output          = /var/run/lirc/lircd
pidfile         = /var/run/lirc/lircd.pid
plugindir       = /usr/lib/arm-linux-gnueabihf/lirc/plugins
permission      = 666
allow-simulate  = No
repeat-max      = 600
#effective-user =
#listen         = [address:]port
#connect        = host[:port]
#loglevel       = 6
#release        = true
#release_suffix = _EVUP
#logfile        = ...
#driver-options = ...

[lircmd]
uinput          = False
nodaemon        = False

# [modinit]
# code = /usr/sbin/modprobe lirc_serial
# code1 = /usr/bin/setfacl -m g:lirc:rw /dev/uinput
# code2 = ...


# [lircd-uinput]
# add-release-events = False
# release-timeout    = 200
# release-suffix     = _EVUP

driver    = default
device    = /dev/lirc0

driver    = default
device    = /dev/lirc0




Any idea?