Re: Compro Videomate U500

[Matthew V. <mat...@gm...>]

On Dec 22, 2007 4:33 PM, Matthew Vermeulen <mat...@gm...> wrote:

> Hi all,
>
> I have a Compro Videomate U500 USB dvb-t tuner...
> (http://www.comprousa.com/New/en/product/u500/u500.html)
> So far I've managed to get all the dvb related stuff all set up, but I am
> unable to get the included remote to work. I've tried most stuff I can think
> of, so it'd be great if someone could point me in the right direction.
>
> Further to my earlier post, I've since tested the remote in windows (took
ages to set up too :( ) and can confirm that it works there. Essentially, I
cannot find a module to load which will work - I've tried most lirc_*
modules and nothign produces output with irrecord or mode2, although a few
modules do make a /dev/lirc0 file appear. After boot up there is only a
/dev/lircd device. Below is the output of lsusb -vv relevant to my device.

Bus 002 Device 005: ID 185b:1e78 Compro
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x185b Compro
  idProduct          0x1e78
  bcdDevice            1.00
  iManufacturer           1 Compro
  iProduct                2 VideoMateU500
  iSerial                 3 0000000001
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           46
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           4
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              10
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Hope someone can help :)

Cheers,

Matt



-- 
Matthew Vermeulen
http://www.matthewv.id.au/
MatthewV @ irc.freenode.net