[linuxsh-shmedia-dev] Tekram DC-390U3W SCSI card

SourceForge Headquarters 1320 Columbia Street Suite 310 San Diego, CA 92101 +1 (858) 422-6466

Hi,

Has anyone got any experiences with this card?  I've got one plugged
into my Cayman but I'm not having much luck getting it to work.

I've enabled the "SYM53C8XX Version 2 SCSI support" driver, which claims
to support the chipset on the card (lspci reports the card like this:)

00:02.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 Ultra3=
 SCSI Adapter (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParEr=
r- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort=
- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (4250ns min, 4500ns max), cache line size 08
        Interrupt: pin A routed to IRQ 6
        Region 0: I/O ports at 3400 [size=3D256]
        Region 1: Memory at 46144400 (64-bit, non-prefetchable) [size=3D1=
K]
        Region 3: Memory at 46140000 (64-bit, non-prefetchable) [size=3D8=
K]
        Expansion ROM at 46120000 [disabled] [size=3D64K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0-,D1-,=
D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME-

00:02.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 Ultra3=
 SCSI Adapter (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParEr=
r- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort=
- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (4250ns min, 4500ns max), cache line size 08
        Interrupt: pin A routed to IRQ 6
        Region 0: I/O ports at 3800 [size=3D256]
        Region 1: Memory at 46144800 (64-bit, non-prefetchable) [size=3D1=
K]
        Region 3: Memory at 46142000 (64-bit, non-prefetchable) [size=3D8=
K]
        Expansion ROM at 46130000 [disabled] [size=3D64K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0-,D1-,=
D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME-

Currently I haven't got a HDD plugged into the card.  I've tried both
3.3 and 5V slots.  Every time, my bootup gets stuck like this:

SCSI subsystem driver Revision: 1.00
sym.2.0.0: setting PCI_COMMAND_PARITY...
sym.2.0.0: setting PCI_COMMAND_INVALIDATE.
sym.2.0.1: setting PCI_COMMAND_PARITY...
sym.2.0.1: setting PCI_COMMAND_INVALIDATE.
sym0: <1010-33> rev 0x1 on pci bus 2 device 0 function 0 irq 88
pci_alloc_consistent returns a07c0000, phys 0x807c0000, mapped to f408400=
0
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
pci_alloc_consistent returns a07bf000, phys 0x807bf000, mapped to f408b00=
0
pci_alloc_consistent returns a07be000, phys 0x807be000, mapped to f408d00=
0
pci_alloc_consistent returns a07bd000, phys 0x807bd000, mapped to f408f00=
0
pci_alloc_consistent returns a07bc000, phys 0x807bc000, mapped to f409100=
0
sym0: SCSI BUS has been reset.
sym1: <1010-33> rev 0x1 on pci bus 2 device 0 function 1 irq 88
pci_alloc_consistent returns a07bb000, phys 0x807bb000, mapped to f409300=
0
sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
pci_alloc_consistent returns a07ba000, phys 0x807ba000, mapped to f409a00=
0
pci_alloc_consistent returns a07b9000, phys 0x807b9000, mapped to f409c00=
0
pci_alloc_consistent returns a07b8000, phys 0x807b8000, mapped to f409e00=
0
pci_alloc_consistent returns a07b7000, phys 0x807b7000, mapped to f40a000=
0
sym1: SCSI BUS has been reset.
sym0:0: ERROR (0:8) (0-0-0) (0/0/0) @ (scriptb 8:6f388af5).
sym0: script cmd =3D 80080000
sym0: regdump: ca 00 00 00 47 00 00 0f 00 08 00 00 80 00 00 0a 00 00 7c 8=
0 20 00 00 00.
sym1: SCSI BUS mode change from SE to SE.
sym1: SCSI BUS has been reset.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sym1:0: ERROR (0:8) (0-0-0) (0/0/0) @ (scriptb 8:ea220d65).
sym1: script cmd =3D 80080000
sym1: regdump: ca 00 00 00 47 00 00 0f 00 08 00 00 80 00 08 0a 00 b0 7b 8=
0 20 00 00 00.
sym0:0: ERROR (0:8) (0-0-0) (0/0/0) @ (scriptb 8:6f388af5).
sym0: script cmd =3D 80080000
sym0: regdump: ca 00 00 00 47 00 00 0f 00 08 00 00 80 00 00 0a 00 00 7c 8=
0 20 00 00 00.
sym1: SCSI BUS reset detected.
sym1: SCSI BUS has been reset.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sym1:0: ERROR (0:8) (0-0-0) (0/0/0) @ (scriptb 8:ea220d65).
sym1: script cmd =3D 80080000
sym1: regdump: ca 00 00 00 47 00 00 0f 00 08 00 00 80 00 08 0a 00 b0 7b 8=
0 20 00 00 00.

which just keeps going on and on until I reset the board.  Being a
non-SCSI-expert who was na=EFvely hoping this would work OOB, I'm pretty
stuck.

Any ideas?  e.g. has this card ever been got working on SH-4 and if so
what was the trick (if any)?

Cheers
Richard

--=20
Richard \\\ SuperH Core+Debug Architect /// .. At home ..
  P.    /// ric...@su...  ///  rc...@rc...
Curnow  \\\ http://www.superh.com/    ///  www.rc0.org.uk