Menu
▾
▴
[PATCH 3/5] SH7720: MPR2: basic support
|
From: Markus B. <sup...@go...> - 2007-08-17 22:35:48
|
Hi, this adds basic support for the Magic Panel R2 board. The irq initialisation was migrated to the new intc code. This reduced the size of the irq setup considerably, and because of that got merged into setup.c The write size for the heartbeat module was adjusted with an ifdef The patch for the default config is attached. The default config won't compile, but this is a general dsp problem since 2.6.23-rc1 http://marc.info/?l=linuxsh-dev&m=118734760923296&w=2 Signed-off by: Markus Brunner <sup...@gm...> Signed-off by: Mark Jonas <to...@gm...> --- arch/sh/Kconfig | 7 arch/sh/Makefile | 1 arch/sh/boards/magicpanelr2/Kconfig | 13 + arch/sh/boards/magicpanelr2/Makefile | 5 arch/sh/boards/magicpanelr2/setup.c | 319 +++++++++++++++++++++++++++++++++++ arch/sh/drivers/heartbeat.c | 4 include/asm-sh/magicpanelr2.h | 67 +++++++ 7 files changed, 416 insertions(+) --- sh-2.6-intc/arch/sh/boards/magicpanelr2/Kconfig 1970-01-01 01:00:00.000000000 +0100 +++ sh-2.6/arch/sh/boards/magicpanelr2/Kconfig 2007-08-03 10:16:35.000000000 +0200 @@ -0,0 +1,13 @@ +if SH_MAGIC_PANEL_R2 + +menu "Magic Panel R2 options" + +config SH_MAGIC_PANEL_R2_VERSION + int SH_MAGIC_PANEL_R2_VERSION + default "3" + help + Set the version of the Magic Panel R2 + +endmenu + +endif --- sh-2.6-intc/arch/sh/boards/magicpanelr2/Makefile 1970-01-01 01:00:00.000000000 +0100 +++ sh-2.6/arch/sh/boards/magicpanelr2/Makefile 2007-08-16 17:16:42.000000000 +0200 @@ -0,0 +1,5 @@ +# +# Makefile for the Magic Panel specific parts +# + +obj-y := setup.o \ No newline at end of file --- sh-2.6-intc/arch/sh/boards/magicpanelr2/setup.c 1970-01-01 01:00:00.000000000 +0100 +++ sh-2.6/arch/sh/boards/magicpanelr2/setup.c 2007-08-17 11:28:54.000000000 +0200 @@ -0,0 +1,319 @@ +/* + * linux/arch/sh/boards/magicpanel/setup.c + * + * Copyright (C) 2007 Markus Brunner, Mark Jonas + * + * Magic Panel Release 2 board setup + * + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ + +#include <linux/autoconf.h> +#include <linux/init.h> +#include <linux/irq.h> +#include <linux/platform_device.h> + +#include <linux/hdreg.h> +#include <linux/ide.h> +#include <asm/magicpanelr2.h> +#include <linux/irq.h> +#include <linux/delay.h> + +static void __init setup_chip_select(void); +static int __init ethernet_reset_finished(void); +static void __init setup_port_multiplexing(void); +static void __init reset_ethernet(void); + +#define LAN9115_READY (ctrl_inl(0xA8000084UL) & 0x00000001UL) + +/* Wait until reset finished. Timeout is 100ms. */ +static int __init ethernet_reset_finished(void) +{ + int i; + + if (LAN9115_READY) + return 1; + + for (i = 0; i < 10; ++i) { + mdelay(10); + if (LAN9115_READY) + return 1; + } + + return 0; +} + +static void __init reset_ethernet(void) +{ + /* PMDR: LAN_RESET=on */ + CLRBITS_OUTB(0x10, PORT_PMDR); + + udelay(200); + + /* PMDR: LAN_RESET=off */ + SETBITS_OUTB(0x10, PORT_PMDR); +} + +static void __init setup_chip_select(void) +{ + /* CS2: LAN (0x08000000 - 0x0bffffff) */ + /* no idle cycles, normal space, 8 bit data bus */ + ctrl_outl(0x36db0400, CS2BCR); + /* (SW:1.5 WR:3 HW:1.5), ext. wait */ + ctrl_outl(0x000003c0, CS2WCR); + + /* CS4: CAN1 (0xb0000000 - 0xb3ffffff) */ + /* no idle cycles, normal space, 8 bit data bus */ + ctrl_outl(0x00000200, CS4BCR); + /* (SW:1.5 WR:3 HW:1.5), ext. wait */ + ctrl_outl(0x00100981, CS4WCR); + + /* CS5a: CAN2 (0xb4000000 - 0xb5ffffff) */ + /* no idle cycles, normal space, 8 bit data bus */ + ctrl_outl(0x00000200, CS5ABCR); + /* (SW:1.5 WR:3 HW:1.5), ext. wait */ + ctrl_outl(0x00100981, CS5AWCR); + + /* CS5b: CAN3 (0xb6000000 - 0xb7ffffff) */ + /* no idle cycles, normal space, 8 bit data bus */ + ctrl_outl(0x00000200, CS5BBCR); + /* (SW:1.5 WR:3 HW:1.5), ext. wait */ + ctrl_outl(0x00100981, CS5BWCR); + + /* CS6a: Rotary (0xb8000000 - 0xb9ffffff) */ + /* no idle cycles, normal space, 8 bit data bus */ + ctrl_outl(0x00000200, CS6ABCR); + /* (SW:1.5 WR:3 HW:1.5), no ext. wait */ + ctrl_outl(0x001009C1, CS6AWCR); +} + +static void __init setup_port_multiplexing(void) +{ + /* A7 GPO(LED8); A6 GPO(LED7); A5 GPO(LED6); A4 GPO(LED5); + * A3 GPO(LED4); A2 GPO(LED3); A1 GPO(LED2); A0 GPO(LED1); + */ + ctrl_outw(0x5555, PORT_PACR); /* 01 01 01 01 01 01 01 01 */ + + /* B7 GPO(RST4); B6 GPO(RST3); B5 GPO(RST2); B4 GPO(RST1); + * B3 GPO(PB3); B2 GPO(PB2); B1 GPO(PB1); B0 GPO(PB0); + */ + ctrl_outw(0x5555, PORT_PBCR); /* 01 01 01 01 01 01 01 01 */ + + /* C7 GPO(PC7); C6 GPO(PC6); C5 GPO(PC5); C4 GPO(PC4); + * C3 LCD_DATA3; C2 LCD_DATA2; C1 LCD_DATA1; C0 LCD_DATA0; + */ + ctrl_outw(0x5500, PORT_PCCR); /* 01 01 01 01 00 00 00 00 */ + + /* D7 GPO(PD7); D6 GPO(PD6); D5 GPO(PD5); D4 GPO(PD4); + * D3 GPO(PD3); D2 GPO(PD2); D1 GPO(PD1); D0 GPO(PD0); + */ + ctrl_outw(0x5555, PORT_PDCR); /* 01 01 01 01 01 01 01 01 */ + + /* E7 (x); E6 GPI(nu); E5 GPI(nu); E4 LCD_M_DISP; + * E3 LCD_CL1; E2 LCD_CL2; E1 LCD_DON; E0 LCD_FLM; + */ + ctrl_outw(0x3C00, PORT_PECR); /* 00 11 11 00 00 00 00 00 */ + + /* F7 (x); F6 DA1(VLCD); F5 DA0(nc); F4 AN3; + * F3 AN2(MID_AD); F2 AN1(EARTH_AD); F1 AN0(TEMP); F0 GPI+(nc); + */ + ctrl_outw(0x0002, PORT_PFCR); /* 00 00 00 00 00 00 00 10 */ + + /* G7 (x); G6 IRQ5(TOUCH_BUSY); G5 IRQ4(TOUCH_IRQ); G4 GPI(KEY2); + * G3 GPI(KEY1); G2 GPO(LED11); G1 GPO(LED10); G0 GPO(LED9); + */ + ctrl_outw(0x03D5, PORT_PGCR); /* 00 00 00 11 11 01 01 01 */ + + /* H7 (x); H6 /RAS(BRAS); H5 /CAS(BCAS); H4 CKE(BCKE); + * H3 GPO(EARTH_OFF); H2 GPO(EARTH_TEST); H1 USB2_PWR; H0 USB1_PWR; + */ + ctrl_outw(0x0050, PORT_PHCR); /* 00 00 00 00 01 01 00 00 */ + + /* J7 (x); J6 AUDCK; J5 ASEBRKAK; J4 AUDATA3; + * J3 AUDATA2; J2 AUDATA1; J1 AUDATA0; J0 AUDSYNC; + */ + ctrl_outw(0x0000, PORT_PJCR); /* 00 00 00 00 00 00 00 00 */ + + /* K7 (x); K6 (x); K5 (x); K4 (x); + * K3 PINT7(/PWR2); K2 PINT6(/PWR1); K1 PINT5(nu); K0 PINT4(FLASH_READY) + */ + ctrl_outw(0x00FF, PORT_PKCR); /* 00 00 00 00 11 11 11 11 */ + + /* L7 TRST; L6 TMS; L5 TDO; L4 TDI; + * L3 TCK; L2 (x); L1 (x); L0 (x); + */ + ctrl_outw(0x0000, PORT_PLCR); /* 00 00 00 00 00 00 00 00 */ + + /* M7 GPO(CURRENT_SINK); M6 GPO(PWR_SWITCH); M5 GPO(LAN_SPEED); + * M4 GPO(LAN_RESET); M3 GPO(BUZZER); M2 GPO(LCD_BL); + * M1 CS5B(CAN3_CS); M0 GPI+(nc); + */ + ctrl_outw(0x5552, PORT_PMCR); /* 01 01 01 01 01 01 00 10 */ + + /* CURRENT_SINK=off, PWR_SWITCH=off, LAN_SPEED=100MBit, + * LAN_RESET=off, BUZZER=off, LCD_BL=off + */ +#if CONFIG_SH_MAGIC_PANEL_R2_VERSION == 2 + ctrl_outb(0x30, PORT_PMDR); +#elif CONFIG_SH_MAGIC_PANEL_R2_VERSION == 3 + ctrl_outb(0xF0, PORT_PMDR); +#else +#error Unknown revision of PLATFORM_MP_R2 +#endif + + /* P7 (x); P6 (x); P5 (x); + * P4 GPO(nu); P3 IRQ3(LAN_IRQ); P2 IRQ2(CAN3_IRQ); + * P1 IRQ1(CAN2_IRQ); P0 IRQ0(CAN1_IRQ) + */ + ctrl_outw(0x0100, PORT_PPCR); /* 00 00 00 01 00 00 00 00 */ + ctrl_outb(0x10, PORT_PPDR); + + /* R7 A25; R6 A24; R5 A23; R4 A22; + * R3 A21; R2 A20; R1 A19; R0 A0; + */ + ctrl_outw(0x0000, PORT_PRCR); /* 00 00 00 00 00 00 00 00 */ + + /* S7 (x); S6 (x); S5 (x); S4 GPO(EEPROM_CS2); + * S3 GPO(EEPROM_CS1); S2 SIOF0_TXD; S1 SIOF0_RXD; S0 SIOF0_SCK; + */ + ctrl_outw(0x0140, PORT_PSCR); /* 00 00 00 01 01 00 00 00 */ + + /* T7 (x); T6 (x); T5 (x); T4 COM1_CTS; + * T3 COM1_RTS; T2 COM1_TXD; T1 COM1_RXD; T0 GPO(WDOG) + */ + ctrl_outw(0x0001, PORT_PTCR); /* 00 00 00 00 00 00 00 01 */ + + /* U7 (x); U6 (x); U5 (x); U4 GPI+(/AC_FAULT); + * U3 GPO(TOUCH_CS); U2 TOUCH_TXD; U1 TOUCH_RXD; U0 TOUCH_SCK; + */ + ctrl_outw(0x0240, PORT_PUCR); /* 00 00 00 10 01 00 00 00 */ + + /* V7 (x); V6 (x); V5 (x); V4 GPO(MID2); + * V3 GPO(MID1); V2 CARD_TxD; V1 CARD_RxD; V0 GPI+(/BAT_FAULT); + */ + ctrl_outw(0x0142, PORT_PVCR); /* 00 00 00 01 01 00 00 10 */ +} + +static void __init mpr2_setup(char **cmdline_p) +{ + __set_io_port_base(0xa0000000); + + /* set Pin Select Register A: + * /PCC_CD1, /PCC_CD2, PCC_BVD1, PCC_BVD2, + * /IOIS16, IRQ4, IRQ5, USB1d_SUSPEND + */ + ctrl_outw(0xAABC, PORT_PSELA); + /* set Pin Select Register B: + * /SCIF0_RTS, /SCIF0_CTS, LCD_VCPWC, + * LCD_VEPWC, IIC_SDA, IIC_SCL, Reserved + */ + ctrl_outw(0x3C00, PORT_PSELB); + /* set Pin Select Register C: + * SIOF1_SCK, SIOF1_RxD, SCIF1_RxD, SCIF1_TxD, Reserved + */ + ctrl_outw(0x0000, PORT_PSELC); + /* set Pin Select Register D: Reserved, SIOF1_TxD, Reserved, SIOF1_MCLK, + * Reserved, SIOF1_SYNC, Reserved, SCIF1_SCK, Reserved + */ + ctrl_outw(0x0000, PORT_PSELD); + /* set USB TxRx Control: Reserved, DRV, Reserved, USB_TRANS, USB_SEL */ + ctrl_outw(0x0101, PORT_UTRCTL); + /* set USB Clock Control: USSCS, USSTB, Reserved (HighByte always A5) */ + ctrl_outw(0xA5C0, PORT_UCLKCR_W); + + setup_chip_select(); + + setup_port_multiplexing(); + + reset_ethernet(); + + printk(KERN_INFO "Magic Panel Release 2 A.%i\n", + CONFIG_SH_MAGIC_PANEL_R2_VERSION); + + if (ethernet_reset_finished() == 0) + printk(KERN_WARNING "Ethernet not ready\n"); +} + +static struct resource smc911x_resources[] = { + [0] = { + .start = 0xa8000000, + .end = 0xabffffff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 35, + .end = 35, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device smc911x_device = { + .name = "smc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smc911x_resources), + .resource = smc911x_resources, +}; + +static unsigned char heartbeat_bit_pos[] = { 0, 1, 2, 3, 4, 5, 6, 7 }; + +static struct resource heartbeat_resources[] = { + [0] = { + .start = PA_LED, + .end = PA_LED + ARRAY_SIZE(heartbeat_bit_pos) - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device heartbeat_device = { + .name = "heartbeat", + .id = -1, + .dev = { + .platform_data = heartbeat_bit_pos, + }, + .num_resources = ARRAY_SIZE(heartbeat_resources), + .resource = heartbeat_resources, +}; + +static struct platform_device *mpr2_devices[] __initdata = { + &heartbeat_device, + &smc911x_device, +}; + +static int __init mpr2_devices_setup(void) +{ + return platform_add_devices(mpr2_devices, ARRAY_SIZE(mpr2_devices)); +} +device_initcall(mpr2_devices_setup); + +/* + * Initialize IRQ setting + */ +void __init init_mpr2_IRQ(void) +{ + plat_irq_setup_pins(IRQ_MODE_IRQ); /* install handlers for IRQ0-5 */ + + set_irq_type(32, IRQ_TYPE_LEVEL_LOW); /* IRQ0 CAN1 */ + set_irq_type(33, IRQ_TYPE_LEVEL_LOW); /* IRQ1 CAN2 */ + set_irq_type(34, IRQ_TYPE_LEVEL_LOW); /* IRQ2 CAN3 */ + set_irq_type(35, IRQ_TYPE_LEVEL_LOW); /* IRQ3 SMSC9115 */ + set_irq_type(36, IRQ_TYPE_EDGE_RISING); /* IRQ4 touchscreen */ + set_irq_type(37, IRQ_TYPE_EDGE_FALLING); /* IRQ5 touchscreen */ + + intc_set_priority(32, 13); /* IRQ0 CAN1 */ + intc_set_priority(33, 13); /* IRQ0 CAN2 */ + intc_set_priority(34, 13); /* IRQ0 CAN3 */ + intc_set_priority(35, 6); /* IRQ3 SMSC9115 */ +} + +/* + * The Machine Vector + */ + +static struct sh_machine_vector mv_mpr2 __initmv = { + .mv_name = "mpr2", + .mv_setup = mpr2_setup, + .mv_init_irq = init_mpr2_IRQ, +}; --- sh-2.6-intc/arch/sh/drivers/heartbeat.c 2007-07-31 12:11:46.000000000 +0200 +++ sh-2.6/arch/sh/drivers/heartbeat.c 2007-08-03 10:09:05.000000000 +0200 @@ -39,7 +39,11 @@ static void heartbeat_timer(unsigned lon struct heartbeat_data *hd = (struct heartbeat_data *)data; static unsigned bit = 0, up = 1; +#if defined(CONFIG_SH_MAGIC_PANEL_R2) + ctrl_outb(~(1 << hd->bit_pos[bit]), (unsigned long)hd->base); +#else ctrl_outw(1 << hd->bit_pos[bit], (unsigned long)hd->base); +#endif bit += up; if ((bit == 0) || (bit == ARRAY_SIZE(hd->bit_pos)-1)) up = -up; --- sh-2.6-intc/arch/sh/Kconfig 2007-08-08 22:59:29.000000000 +0200 +++ sh-2.6/arch/sh/Kconfig 2007-08-16 15:52:11.000000000 +0200 @@ -395,11 +395,18 @@ config SH_X3PROTO bool "SH-X3 Prototype board" depends on CPU_SUBTYPE_SHX3 +config SH_MAGIC_PANEL_R2 + bool "Magic Panel R2" + depends on CPU_SUBTYPE_SH7720 + help + Select Magic Panel R2 if configuring for Magic Panel R2. + endmenu source "arch/sh/boards/renesas/hs7751rvoip/Kconfig" source "arch/sh/boards/renesas/rts7751r2d/Kconfig" source "arch/sh/boards/renesas/r7780rp/Kconfig" +source "arch/sh/boards/magicpanelr2/Kconfig" menu "Timer and clock configuration" --- sh-2.6-intc/arch/sh/Makefile 2007-08-14 08:33:48.000000000 +0200 +++ sh-2.6/arch/sh/Makefile 2007-08-17 13:11:28.000000000 +0200 @@ -111,6 +111,7 @@ machdir-$(CONFIG_SH_SHMIN) += shmin machdir-$(CONFIG_SH_7206_SOLUTION_ENGINE) += se/7206 machdir-$(CONFIG_SH_7619_SOLUTION_ENGINE) += se/7619 machdir-$(CONFIG_SH_LBOX_RE2) += lboxre2 +machdir-$(CONFIG_SH_MAGIC_PANEL_R2) += magicpanelr2 incdir-y := $(notdir $(machdir-y)) --- sh-2.6-intc/include/asm-sh/magicpanelr2.h 1970-01-01 01:00:00.000000000 +0100 +++ sh-2.6/include/asm-sh/magicpanelr2.h 2007-08-17 08:28:52.000000000 +0200 @@ -0,0 +1,67 @@ +/* + * include/asm-sh/magicpanelr2.h + * + * Copyright (C) 2007 Markus Brunner, Mark Jonas + * + * I/O addresses and bitmasks for Magic Panel Release 2 board + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ + +#ifndef __ASM_SH_MAGICPANELR2_H +#define __ASM_SH_MAGICPANELR2_H + +#include <asm/port.h> + +#define __IO_PREFIX mpr2 +#include <asm/io_generic.h> + + +#define SETBITS_OUTB(mask, reg) ctrl_outb(ctrl_inb(reg) | mask, reg) +#define SETBITS_OUTW(mask, reg) ctrl_outw(ctrl_inw(reg) | mask, reg) +#define SETBITS_OUTL(mask, reg) ctrl_outl(ctrl_inl(reg) | mask, reg) +#define CLRBITS_OUTB(mask, reg) ctrl_outb(ctrl_inb(reg) & ~mask, reg) +#define CLRBITS_OUTW(mask, reg) ctrl_outw(ctrl_inw(reg) & ~mask, reg) +#define CLRBITS_OUTL(mask, reg) ctrl_outl(ctrl_inl(reg) & ~mask, reg) + + +#define PA_LED PORT_PADR /* LED */ + + +/* BSC */ +#define CMNCR 0xA4FD0000UL +#define CS0BCR 0xA4FD0004UL +#define CS2BCR 0xA4FD0008UL +#define CS3BCR 0xA4FD000CUL +#define CS4BCR 0xA4FD0010UL +#define CS5ABCR 0xA4FD0014UL +#define CS5BBCR 0xA4FD0018UL +#define CS6ABCR 0xA4FD001CUL +#define CS6BBCR 0xA4FD0020UL +#define CS0WCR 0xA4FD0024UL +#define CS2WCR 0xA4FD0028UL +#define CS3WCR 0xA4FD002CUL +#define CS4WCR 0xA4FD0030UL +#define CS5AWCR 0xA4FD0034UL +#define CS5BWCR 0xA4FD0038UL +#define CS6AWCR 0xA4FD003CUL +#define CS6BWCR 0xA4FD0040UL + + +/* usb */ + +#define PORT_UTRCTL 0xA405012CUL +#define PORT_UCLKCR_W 0xA40A0008UL + +#define INTC_ICR0 0xA414FEE0UL +#define INTC_ICR1 0xA4140010UL +#define INTC_ICR2 0xA4140012UL + +/* MTD */ + +#define MPR2_MTD_BOOTLOADER_SIZE 0x00060000UL +#define MPR2_MTD_KERNEL_SIZE 0x00200000UL + +#endif /* __ASM_SH_MAGICPANELR2_H */ |
