Menu
▾
▴
[LV-kern-commit] CVS: kernel-2.4/drivers/vax/net Makefile,NONE,1.1 delqa-regs.h,NONE,1.1 delqa.c,NONE,1.1
|
From: Dave A. <ai...@us...> - 2002-10-25 17:25:38
|
Update of /cvsroot/linux-vax/kernel-2.4/drivers/vax/net
In directory usw-pr-cvs1:/tmp/cvs-serv27297/net
Added Files:
Makefile delqa-regs.h delqa.c
Log Message:
DA: backport from 2.5 of Kenns qbus/delqa work - delqa/qbus works iprcons is not working..
needed for SIMH emu
--- NEW FILE ---
#
# Makefile for the Linux/VAX network device drivers.
#
O_TARGET := vaxnet.o
obj-y :=
obj-m :=
obj-n :=
obj-$(CONFIG_DELQA) += delqa.o
include $(TOPDIR)/Rules.make
--- NEW FILE ---
/* Register offsets */
#define DELQA_ADDR1 0
#define DELQA_ADDR2 2
#define DELQA_RCLL 4 /* loword of first RX descriptor addr */
#define DELQA_RCLH 6 /* hiword of first RX descriptor addr */
#define DELQA_XMTL 8 /* loword of first TX descriptor addr */
#define DELQA_XMTH 10 /* hiword of first TX descriptor addr */
#define DELQA_VECTOR 12 /* Q-bus interrupt vector */
#define DELQA_CSR 14 /* control & status */
/* Bits in CSR */
#define DELQA_CSR_RCV_ENABLE 0x0001 /* Receiver enable */
#define DELQA_CSR_RESET 0x0002 /* Software reset */
#define DELQA_CSR_NEX_MEM_INT 0x0004 /* Non-existent memory interrupt */
#define DELQA_CSR_LOAD_ROM 0x0008 /* Load boot/diag from rom */
#define DELQA_CSR_XL_INVALID 0x0010 /* Transmit list invalid */
#define DELQA_CSR_RL_INVALID 0x0020 /* Receive list invalid */
#define DELQA_CSR_INT_ENABLE 0x0040 /* Interrupt enable */
#define DELQA_CSR_XMIT_INT 0x0080 /* Transmit interrupt */
#define DELQA_CSR_ILOOP 0x0100 /* Internal loopback */
#define DELQA_CSR_ELOOP 0x0200 /* External loopback */
#define DELQA_CSR_STIM_ENABLE 0x0400 /* Sanity timer enable */
#define DELQA_CSR_POWERUP 0x1000 /* Transceiver power on */
#define DELQA_CSR_CARRIER 0x2000 /* Carrier detect */
#define DELQA_CSR_RCV_INT 0x8000 /* Receiver interrupt */
/* Bits in ADDR_HI field in descriptors */
#define DELQA_ADDRHI_VALID 0x8000 /* ADDRHI/LO are valid */
#define DELQA_ADDRHI_CHAIN 0x4000 /* ADDRHI/LO points to next descriptor */
#define DELQA_ADDRHI_EOMSG 0x2000 /* Buffer contains last byte of frame */
#define DELQA_ADDRHI_SETUP 0x1000 /* Buffer contains a setup frame */
#define DELQA_ADDRHI_ODDEND 0x0080 /* last byte not on word boundary */
#define DELQA_ADDRHI_ODDBEGIN 0x0040 /* first byte not on word boundary */
/* Bits in buffer descriptor field STATUS1 for transmit */
#define DELQA_TXSTS1_LASTNOT 0x8000
#define DELQA_TXSTS1_ERRORUSED 0x4000
#define DELQA_TXSTS1_LOSS 0x1000
#define DELQA_TXSTS1_NOCARRIER 0x0800
#define DELQA_TXSTS1_STE16 0x0400
#define DELQA_TXSTS1_ABORT 0x0200
#define DELQA_TXSTS1_FAIL 0x0100
#define DELQA_TXSTS1_COUNT_MASK 0x00f0
#define DELQA_TXSTS1_COUNT_SHIFT 4
/* Special value that signifies that descriptor is not yet used
by DELQA. The descriptor FLAG and STATUS1 fields both get
initialized to this value. */
#define DELQA_NOTYET 0x8000
/* Bits in buffer descriptor field STATUS1 for transmit */
#define DELQA_TXSTS2_TDR_MASK 0x3fff
#define DELQA_TXSTS2_TDR_SHIFT 0
/* Bits in buffer descriptor field STATUS1 for receive */
#define DELQA_RXSTS1_LASTNOT 0x8000
#define DELQA_RXSTS1_ERRORUSED 0x4000
#define DELQA_RXSTS1_ESETUP 0x2000
#define DELQA_RXSTS1_DISCARD 0x1000
#define DELQA_RXSTS1_RUNT 0x0800
#define DELQA_RXSTS1_LEN_HI_MASK 0x0700
#define DELQA_RXSTS1_LEN_HI_SHIFT 8
#define DELQA_RXSTS1_FRAME 0x0004
#define DELQA_RXSTS1_CRCERR 0x0002
#define DELQA_RXSTS1_OVF 0x0001
/* Bits in buffer descriptor field STATUS2 for receive */
#define DELQA_RXSTS2_LEN_LO1_MASK 0x00ff
#define DELQA_RXSTS2_LEN_LO1_SHIFT 0
#define DELQA_RXSTS2_LEN_LO2_MASK 0xff00
#define DELQA_RXSTS2_LEN_LO2_SHIFT 8
--- NEW FILE ---
/* $Id: delqa.c,v 1.1 2002/10/25 14:04:35 airlied Exp $
Quick-and-dirty driver for DELQA/DESQA (Q-bus ethernet adapters)
(C) 2002, Kenn Humborg
TODO: Pre-allocate the Q-bus mapping registers for TX at init time and
re-use them, rather than allocating them for each packet. This
would remove the only failure possibility from delqa_start_xmit().
TODO: Don't hard-code the interrupt vector. Add an API to the Q-bus
driver to allocate a vector instead.
TODO: Allow multiple DELQAs at different base addresses.
TODO: Reset BELQA on q-bus memory access error (is this the right
thing to do?).
TODO: Implement delqa_tx_timeout().
TODO: Handle multicast addresses and PROMISC flag in format_setup_frame().
TODO: Implement delqa_close().
*/
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <asm/system.h>
#include <asm/bus/qbus.h>
#include "delqa-regs.h"
#define DELQA_DEBUG_REGWR 0
#define DELQA_DEBUG_CSR 0
#define DELQA_DEBUG_DESC 0
#define DELQA_DEBUG_PKT 0
#define DELQA_BASE 0x20001920
#define DELQA_QBUS_VECTOR 4
/* FIXME: Are these numbers OK? These are what NetBSD uses. */
#define RXDESCS 30
#define TXDESCS 60
#define RXBUFSIZE 2048
struct delqa_bufdesc {
unsigned short flag;
unsigned short addr_hi;
unsigned short addr_lo;
signed short buflen;
unsigned short status1;
unsigned short status2;
};
struct delqa_descs {
struct delqa_bufdesc rxdesc[RXDESCS+1];
struct delqa_bufdesc txdesc[TXDESCS+1];
};
struct delqa_private {
unsigned char *base;
unsigned int qbus_vector;
struct net_device_stats stats;
struct delqa_descs *descs;
struct vax_dmamap *desc_map; /* DMA mapping for delqa_descs structure */
struct vax_dmamap *rx_map[RXDESCS]; /* DMA mappings for each RX buffer */
struct vax_dmamap *tx_map[TXDESCS]; /* DMA mappings for each TX buffer */
struct sk_buff *tx_skb[TXDESCS]; /* We TX direct from the SKB */
unsigned char setup_frame[128];
unsigned char setup_frame_len;
unsigned int next_tx_free; /* Only written by mainline code */
unsigned int next_tx_pending; /* Only written by init and interrupt code */
unsigned int next_rx;
unsigned int last_tdr; /* Last Time Domain Reflectometer value on TX */
spinlock_t lock;
};
#define LOWORD(x) ((int)(x) & 0xffff)
#define HIWORD(x) (((int)(x)>>16) & 0xffff)
static unsigned short int read_reg(struct delqa_private *priv, unsigned int offset)
{
volatile unsigned short int *p;
p = (volatile unsigned short *)(priv->base + offset);
return *p;
}
static void write_reg(struct delqa_private *priv, unsigned int offset, unsigned short int value)
{
volatile unsigned short int *p;
#if DELQA_DEBUG_REGWR
char *reg[8] = { "ADDR1", "ADDR2", "RCCL", "RCLH", "XMTL", "XMTH", "VECTOR", "CSR"};
printk("delqa write_reg: offset %02d(%s) value %04x\n", offset, reg[offset/2], value);
#endif
p = (volatile unsigned short *)(priv->base + offset);
*p = value;
}
static void dump_csr(char *msg, struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
unsigned short csr = read_reg(priv, DELQA_CSR);
printk("%s: %s: CSR %04x: %s%s%s%s%s%s%s%s%s%s%s%s%s%s\n",
dev->name,
msg == NULL ? "" : msg, csr,
(csr & DELQA_CSR_RCV_INT) ? " RI" : "",
(csr & DELQA_CSR_CARRIER) ? " CA" : "",
(csr & DELQA_CSR_POWERUP) ? " OK" : "",
(csr & DELQA_CSR_STIM_ENABLE) ? " SE" : "",
(csr & DELQA_CSR_ELOOP) ? " EL" : "",
(csr & DELQA_CSR_ILOOP) ? "" : " IL", /* active low */
(csr & DELQA_CSR_XMIT_INT) ? " XI" : "",
(csr & DELQA_CSR_INT_ENABLE) ? " IE" : "",
(csr & DELQA_CSR_RL_INVALID) ? " RL" : "",
(csr & DELQA_CSR_XL_INVALID) ? " XL" : "",
(csr & DELQA_CSR_LOAD_ROM) ? " BD" : "",
(csr & DELQA_CSR_NEX_MEM_INT) ? " NI" : "",
(csr & DELQA_CSR_RESET) ? " SR" : "",
(csr & DELQA_CSR_RCV_ENABLE) ? " RE" : "");
}
/*
. -> Invalid
+ -> Valid, not yet used by DELQA
* -> Valid, owned by DELQA (in progress)
- -> Valid, processed by DELQA - no errors
x -> Valid, processed by DELQA - with errors
c -> Valid, chain descriptor
*/
static void dump_descs(struct net_device *dev)
{
unsigned int i;
struct delqa_private *priv = (struct delqa_private *)dev->priv;
struct delqa_bufdesc *desc;
printk("%s: TX free=%02d pending=%02d ", dev->name, priv->next_tx_free, priv->next_tx_pending);
for (i=0; i<TXDESCS+1; i++) {
desc = priv->descs->txdesc + i;
if (desc->addr_hi & DELQA_ADDRHI_CHAIN) {
printk("c");
} else if (desc->addr_hi & DELQA_ADDRHI_VALID) {
/* VALID bit set */
switch (desc->status1 & (DELQA_TXSTS1_LASTNOT|DELQA_TXSTS1_ERRORUSED)) {
case 0:
printk("-");
break;
case DELQA_TXSTS1_ERRORUSED:
printk("x");
break;
case DELQA_TXSTS1_LASTNOT:
if (desc->flag & 0x4000) {
printk("*");
} else {
printk("+");
}
break;
case DELQA_TXSTS1_LASTNOT|DELQA_TXSTS1_ERRORUSED:
/* Don't expect this, since we never break packets across buffers */
printk("?");
break;
}
} else {
printk(".");
}
}
printk("\n");
printk("%s: RX next=%02d ", dev->name, priv->next_rx);
for (i=0; i<RXDESCS+1; i++) {
desc = priv->descs->rxdesc + i;
if (desc->addr_hi & DELQA_ADDRHI_CHAIN) {
printk("c");
} else if (desc->addr_hi & DELQA_ADDRHI_VALID) {
/* VALID bit set */
switch (desc->status1 & (DELQA_RXSTS1_LASTNOT|DELQA_RXSTS1_ERRORUSED)) {
case 0:
printk("-");
break;
case DELQA_RXSTS1_ERRORUSED:
printk("x");
break;
case DELQA_RXSTS1_LASTNOT:
if (desc->flag & 0x4000) {
printk("*");
} else {
printk("+");
}
break;
case DELQA_RXSTS1_LASTNOT|DELQA_RXSTS1_ERRORUSED:
/* Don't expect this, since we never break packets across buffers */
printk("?");
break;
}
} else {
printk(".");
}
}
printk("\n");
}
static void delqa_tx_interrupt(struct net_device *dev, struct delqa_private *priv)
{
struct delqa_bufdesc *desc;
int desc_freed = 0;
unsigned int tdr;
unsigned int collisions;
/* Get first descriptor waiting to be "taken back" from
the DELQA */
desc = priv->descs->txdesc + priv->next_tx_pending;
while (desc->status1 != DELQA_NOTYET) {
#if DELQA_DEBUG_PKT
printk("TX desc %d, status1=%04x, status2=%04x\n", priv->next_tx_pending,
desc->status1, desc->status2);
#endif
tdr = (desc->status2 & DELQA_TXSTS2_TDR_MASK) >> DELQA_TXSTS2_TDR_SHIFT;
collisions = (desc->status1 & DELQA_TXSTS1_COUNT_MASK) >> DELQA_TXSTS1_COUNT_SHIFT;
if (desc->status1 & DELQA_TXSTS1_ERRORUSED) {
priv->stats.tx_errors++;
if (desc->status1 & DELQA_TXSTS1_LOSS) {
printk("%s: carrier lost on transmit - "
"ethernet cable problem?",
dev->name);
}
if (desc->status1 & DELQA_TXSTS1_NOCARRIER) {
printk("%s: no carrier on transmit - "
"transceiver or transceiver cable problem?",
dev->name);
}
if (desc->status1 & DELQA_TXSTS1_ABORT) {
if (tdr == priv->last_tdr) {
printk("%s: excessive collisions on transmit",
dev->name);
} else {
printk("%s: excessive collisions on transmit - "
"cable fault at TDR=%d\n",
dev->name, tdr);
}
if (collisions == 0) {
/* Collision counter overflowed */
priv->stats.collisions += 16;
}
}
} else {
if (desc->addr_hi & DELQA_ADDRHI_SETUP) {
/* Don't count setup frames in stats */
} else {
/* Packet got onto the wire */
priv->stats.tx_packets++;
priv->stats.tx_bytes += desc->buflen * 2;
}
}
priv->stats.collisions += collisions;
priv->last_tdr = tdr;
if (desc->addr_hi & DELQA_ADDRHI_SETUP) {
/* Setup frame - no associated skb */
} else {
dev_kfree_skb_irq(priv->tx_skb[priv->next_tx_pending]);
}
/* clear VALID bit */
desc->addr_hi = 0;
/* reclaim descriptor */
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 0;
/* Free the mapping registers */
qbus_unmap(priv->tx_map[priv->next_tx_pending]);
/* At least one descriptor freed up */
desc_freed = 1;
priv->next_tx_pending++;
if (priv->next_tx_pending == TXDESCS) {
priv->next_tx_pending = 0;
}
desc = priv->descs->txdesc + priv->next_tx_pending;
}
if (netif_queue_stopped(dev) && desc_freed) {
netif_wake_queue(dev);
}
}
static void delqa_rx_interrupt(struct net_device *dev, struct delqa_private *priv)
{
struct delqa_bufdesc *desc;
unsigned int len;
struct sk_buff *skb;
unsigned int busaddr;
/* Get first descriptor waiting to be "taken back" from
the DELQA */
desc = priv->descs->rxdesc + priv->next_rx;
while (desc->status1 != DELQA_NOTYET) {
#if DELQA_DEBUG_PKT
printk("RX desc %d, status1=%04x, status2=%04x, len=%d\n", priv->next_rx,
desc->status1, desc->status2, len);
#endif
if (desc->status1 & DELQA_RXSTS1_ESETUP) {
/* This is the loopback of a setup frame - ignore */
} if (desc->status1 & DELQA_RXSTS1_ERRORUSED) {
/* Error while receiving */
priv->stats.rx_errors++;
} else {
/* Good frame received */
unsigned int len_hi;
unsigned int len_lo1;
unsigned int len_lo2;
len_hi = (desc->status1 & DELQA_RXSTS1_LEN_HI_MASK)
>> DELQA_RXSTS1_LEN_HI_SHIFT;
len_lo1 = (desc->status2 & DELQA_RXSTS2_LEN_LO1_MASK)
>> DELQA_RXSTS2_LEN_LO1_SHIFT;
len_lo2 = (desc->status2 & DELQA_RXSTS2_LEN_LO2_MASK)
>> DELQA_RXSTS2_LEN_LO2_SHIFT;
if (len_lo1 != len_lo2) {
printk("%s: DELQA status2 bytes don't match\n", dev->name);
}
len = (len_hi << 8) + len_lo1 + 60;
skb = dev_alloc_skb(len + 2);
if (skb == NULL) {
printk("%s: cannot allocate skb, dropping packet\n", dev->name);
priv->stats.rx_dropped++;
} else {
priv->stats.rx_packets++;
priv->stats.rx_bytes += len;
skb->dev = dev;
skb_reserve(skb, 2);
skb_put(skb, len);
memcpy(skb->data,
priv->rx_map[priv->next_rx]->virtaddr, len);
skb->protocol = eth_type_trans(skb, dev);
netif_rx(skb);
}
}
/* reclaim descriptor */
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 1; /* High and low bytes must be different */
priv->next_rx++;
if (priv->next_rx == RXDESCS) {
priv->next_rx = 0;
}
desc = priv->descs->rxdesc + priv->next_rx;
}
/* DEQNA manual errata sheet states that we must check for an
invalid receive list before leaving the ISR and reset the
buffer list if it is invalid */
if (read_reg(priv, DELQA_CSR) & DELQA_CSR_RL_INVALID) {
printk("%s: receive list invalid - resetting\n", dev->name);
/* The descriptor pointed to by next_rx must be the
first available descriptor. This is because:
o The DELQA doesn't touch the receive list when
RL_INVALID is set.
o The while() loop above stops when next_rx points
to a 'NOTYET' descriptor. */
busaddr = priv->desc_map->busaddr +
offsetof(struct delqa_descs, rxdesc[priv->next_rx]);
write_reg(priv, DELQA_RCLL, LOWORD(busaddr));
write_reg(priv, DELQA_RCLH, HIWORD(busaddr));
}
}
static void delqa_interrupt(const int irq, void *dev_id, struct pt_regs *regs)
{
struct net_device *dev = (struct net_device *)dev_id;
struct delqa_private *priv = (struct delqa_private *)dev->priv;
unsigned int csr;
unsigned int newcsr;
spin_lock(&priv->lock);
csr = read_reg(priv, DELQA_CSR);
#if DELQA_DEBUG_CSR
dump_csr("delqa_interrupt entry", dev);
#endif
#if DELQA_DEBUG_DESC
dump_descs(dev);
#endif
newcsr = DELQA_CSR_ILOOP | DELQA_CSR_RCV_ENABLE | DELQA_CSR_INT_ENABLE;
if (csr & DELQA_CSR_XMIT_INT) {
/* Either memory read error or tx interrupt */
if (csr & DELQA_CSR_NEX_MEM_INT) {
dump_csr("Q-bus memory error", dev);
dump_descs(dev);
qbus_dumpmap();
/* FIXME: what should we do here? */
panic("DELQA bus memory access error");
} else {
newcsr |= DELQA_CSR_XMIT_INT;
delqa_tx_interrupt(dev, priv);
}
}
if (csr & DELQA_CSR_RCV_INT) {
newcsr |= DELQA_CSR_RCV_INT;
delqa_rx_interrupt(dev, priv);
}
/* Clear RX and TX interrupt bits to allow further interrupts. We
also enable the receiver and turn off the internal loopback at
this point. */
write_reg(priv, DELQA_CSR, newcsr);
#if DELQA_DEBUG_CSR
dump_csr("delqa_interrupt exit", dev);
#endif
spin_unlock(&priv->lock);
}
static int delqa_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
struct delqa_bufdesc *desc;
unsigned int len;
unsigned int i;
unsigned int busaddr;
unsigned int csr;
unsigned int flags;
if (skb->len < ETH_ZLEN) {
struct sk_buff *new_skb;
new_skb = skb_copy_expand(skb, 0, ETH_ZLEN - skb->len, GFP_ATOMIC);
if (new_skb == NULL) {
return -ENOMEM;
}
memset(skb_put(new_skb, ETH_ZLEN - skb->len), 0,
ETH_ZLEN - skb->len);
dev_kfree_skb(skb);
/* We must not return a failure after this point, since that
would result in the caller trying to free the skb that we've
just freed. */
skb = new_skb;
}
spin_lock_irqsave(&priv->lock, flags);
i = priv->next_tx_free;
priv->next_tx_free++;
if (priv->next_tx_free == TXDESCS) {
priv->next_tx_free = 0;
}
spin_unlock_irqrestore(&priv->lock, flags);
desc = priv->descs->txdesc + i;
/* FIXME: These mapping registers MUST be allocated at init time
to prevent any possibility of failure here - see above comment */
priv->tx_map[i] = qbus_alloc_mapregs(skb->data, skb->len);
if (priv->tx_map[i] == NULL) {
/* FIXME: What should I do here? */
panic("delqa_start_xmit: no map reg");
}
priv->tx_skb[i] = skb;
busaddr = priv->tx_map[i]->busaddr;
desc->addr_lo = LOWORD(busaddr);
desc->addr_hi = HIWORD(busaddr) | DELQA_ADDRHI_EOMSG;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 0;
/* Work out the length and alignment stuff */
len = skb->len;
if ((len & 1) || ((unsigned long)(skb->data) & 1)) {
len += 2;
}
if ((unsigned long)(skb->data) & 1) {
desc->addr_hi |= DELQA_ADDRHI_ODDBEGIN;
}
if ((unsigned long)(skb->data + len) & 1) {
desc->addr_hi |= DELQA_ADDRHI_ODDEND;
}
desc->buflen = -(len/2);
/* Set the "go" bit on this descriptor */
desc->addr_hi |= DELQA_ADDRHI_VALID;
#if DELQA_DEBUG_DESC
dump_descs(dev);
#endif
spin_lock_irqsave(&priv->lock, flags);
csr = read_reg(priv, DELQA_CSR);
if (csr & DELQA_CSR_XL_INVALID) {
/* Get Q-bus address of first TX descriptor */
busaddr = priv->desc_map->busaddr + offsetof(struct delqa_descs, txdesc[i]);
write_reg(priv, DELQA_XMTL, LOWORD(busaddr));
write_reg(priv, DELQA_XMTH, HIWORD(busaddr));
}
/* Check if the 'next' descriptor is actually free */
desc = priv->descs->txdesc + priv->next_tx_free;
if (desc->addr_hi & DELQA_ADDRHI_VALID) {
/* All descriptors in use - stop tx queue */
netif_stop_queue(dev);
}
spin_unlock_irqrestore(&priv->lock, flags);
return 0;
}
/* FIXME: implement this */
static void delqa_tx_timeout(struct net_device *dev)
{
printk("delqa_tx_timeout not implemented\n");
HALT;
}
static void store_setup_address(unsigned int index, unsigned char *addr,
unsigned char *setup_frame)
{
unsigned int start;
unsigned int i;
if (index < 6) {
start = index + 1;
} else {
start = index + 65;
}
for (i=0; i<6; i++) {
setup_frame[start + i * 8] = addr[i];
}
}
static void format_setup_frame(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
/* Fill in hardware, broadcast and multicast addresses here */
/* Pre-fill with all FF (has side effect of setting all addresses
to the broadcast address) */
memset(priv->setup_frame, 0xff, sizeof(priv->setup_frame));
/* First address will be our unicast address */
store_setup_address(0, dev->dev_addr, priv->setup_frame);
/* FIXME: Store multicast addresses here */
/* FIXME: Use MULTICAST and PROMISC flags to tweak setup_len */
priv->setup_frame_len = 128;
}
/* FIXME: pre-allocate mapping registers for this at init time. Then this
would be a no-fail function */
static void queue_setup_frame(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
struct delqa_bufdesc *desc;
unsigned int busaddr;
unsigned int csr;
unsigned int i;
/* Point the first available TX descriptor at the setup
frame and enable the transmitter */
spin_lock(&priv->lock);
i = priv->next_tx_free;
priv->next_tx_free++;
if (priv->next_tx_free == TXDESCS) {
priv->next_tx_free = 0;
}
spin_unlock(&priv->lock);
desc = priv->descs->txdesc + i;
priv->tx_map[i] = qbus_alloc_mapregs(priv->setup_frame, priv->setup_frame_len);
if (priv->tx_map[i] == NULL) {
panic("delqa queue_setup_frame: dma mapping failed");
}
busaddr = priv->tx_map[i]->busaddr;
desc->addr_lo = LOWORD(busaddr);
desc->addr_hi = HIWORD(busaddr) | DELQA_ADDRHI_SETUP | DELQA_ADDRHI_EOMSG;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 0;
desc->buflen = -priv->setup_frame_len/2; /* (maybe) bytes, not words like all other uses */
desc->addr_hi |= DELQA_ADDRHI_VALID;
#if DELQA_DEBUG_DESC
dump_descs(dev);
#endif
spin_lock(&priv->lock);
csr = read_reg(priv, DELQA_CSR);
if (csr & DELQA_CSR_XL_INVALID) {
/* Get Q-bus address of first TX descriptor */
busaddr = priv->desc_map->busaddr + offsetof(struct delqa_descs, txdesc[i]);
write_reg(priv, DELQA_XMTL, LOWORD(busaddr));
write_reg(priv, DELQA_XMTH, HIWORD(busaddr));
}
spin_unlock(&priv->lock);
}
static void delqa_reset(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
unsigned int csr;
printk("%s: resetting DELQA... ", dev->name);
write_reg(priv, DELQA_CSR, DELQA_CSR_RESET);
udelay(1000);
csr = read_reg(priv, DELQA_CSR);
write_reg(priv, DELQA_CSR, csr & ~DELQA_CSR_RESET);
write_reg(priv, DELQA_VECTOR, priv->qbus_vector);
printk("done\n");
}
static int delqa_open(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
struct delqa_bufdesc *desc;
int i;
unsigned int busaddr;
/* Reset the hardware before hooking the interrupt vector
to guarantee that we won't get any interrupts until we
enable them. */
delqa_reset(dev);
if (qbus_request_irq(priv->qbus_vector, delqa_interrupt, 0, "delqa", dev)) {
printk("delqa_open: cannot get qbus irq %d\n", priv->qbus_vector);
return -EAGAIN;
}
/* Mark the transmit descriptors as not yet owned by
the DELQA (and also not VALID). */
for (i=0; i<TXDESCS; i++) {
desc = priv->descs->txdesc + i;
/* Clear VALID bit */
desc->addr_hi = 0;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 0;
}
/* Mark the receive descriptors as not yet owned by
the DELQA. */
for (i=0; i<RXDESCS; i++) {
desc = priv->descs->rxdesc + i;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 1;
}
/* Tell the DELQA where the receive descriptors live (i.e.
which Q-bus addresses are mapped to the descriptor
addresses by the mapping registers. There is no
point in setting the transmit descriptor address, since
there are no valid transmit descriptors yet. When
the card hits an invalid transmit descriptor, it stops
the transmit logic, which can only be restarted by
setting the transmit descriptor address again. */
busaddr = priv->desc_map->busaddr + offsetof(struct delqa_descs, rxdesc[0]);
write_reg(priv, DELQA_RCLL, LOWORD(busaddr));
write_reg(priv, DELQA_RCLH, HIWORD(busaddr));
write_reg(priv, DELQA_CSR, DELQA_CSR_INT_ENABLE | DELQA_CSR_XMIT_INT | DELQA_CSR_RCV_INT);
format_setup_frame(dev);
queue_setup_frame(dev);
return 0;
}
/* FIXME: implement delqa_close */
static int delqa_close(struct net_device *dev)
{
printk("delqa_close not implemented\n");
HALT;
return 0;
}
static void delqa_set_multicast(struct net_device *dev)
{
format_setup_frame(dev);
queue_setup_frame(dev);
}
static struct net_device_stats *delqa_get_stats(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *) dev->priv;
return &priv->stats;
}
/* This function allocates the receive buffers, allocates and maps
QBUS mapping registers for these buffers, initializes the receive
descriptors to point to these buffers, and sets up the chain
descriptors at the end of the descriptor lists */
static int init_desc_rings(struct net_device *dev)
{
struct delqa_private *priv = (struct delqa_private *)dev->priv;
struct delqa_bufdesc *desc;
unsigned int busaddr;
int i;
for (i=0; i<RXDESCS; i++) {
unsigned char *buf;
buf = kmalloc(RXBUFSIZE, GFP_KERNEL);
if (buf == NULL) {
printk("delqa: Cannot allocate RX buf");
goto cleanup;
}
priv->rx_map[i] = qbus_alloc_mapregs(buf, RXBUFSIZE);
if (priv->rx_map[i] == NULL) {
printk("delqa init_desc_rings: dma mapping failed");
kfree(buf);
goto cleanup;
}
busaddr = priv->rx_map[i]->busaddr;
desc = priv->descs->rxdesc + i;
desc->addr_lo = LOWORD(busaddr);
desc->addr_hi = HIWORD(busaddr);
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
desc->status2 = 1;
desc->buflen = - (RXBUFSIZE / 2); /* words, not bytes */
desc->addr_hi |= DELQA_ADDRHI_VALID;
}
/* Remember that we've allocated one more descriptor than we
need. This one is used to chain the end of the descriptor
list back to the beginning. */
/* Last receive descriptor contains bus address of first desc */
desc = priv->descs->rxdesc + RXDESCS;
busaddr = priv->desc_map->busaddr + offsetof(struct delqa_descs, rxdesc[0]);
desc->addr_lo = LOWORD(busaddr);
desc->addr_hi = HIWORD(busaddr) | DELQA_ADDRHI_VALID | DELQA_ADDRHI_CHAIN;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
/* Last transmit descriptor contains bus address of first desc */
desc = priv->descs->txdesc + TXDESCS;
busaddr = priv->desc_map->busaddr + offsetof(struct delqa_descs, txdesc[0]);
desc->addr_lo = LOWORD(busaddr);
desc->addr_hi = HIWORD(busaddr) | DELQA_ADDRHI_VALID | DELQA_ADDRHI_CHAIN;
desc->flag = DELQA_NOTYET;
desc->status1 = DELQA_NOTYET;
priv->next_tx_free = 0;
priv->next_tx_pending = 0;
priv->next_rx = 0;
return 0;
cleanup:
for (i=0; i<RXDESCS; i++) {
if (priv->rx_map[i] != NULL) {
kfree(priv->rx_map[i]->virtaddr);
qbus_unmap(priv->rx_map[i]);
priv->rx_map[i] = NULL;
}
}
return -ENOMEM;
}
static int delqa_init(struct net_device *dev)
{
struct delqa_private *priv;
int i;
int status = 0;
dev->priv = kmalloc(sizeof(struct delqa_private), GFP_KERNEL);
if (dev->priv == NULL) {
return -ENOMEM;
}
memset(dev->priv, 0, sizeof(struct delqa_private));
priv = (struct delqa_private *) dev->priv;
spin_lock_init(&priv->lock);
priv->base = ioremap(DELQA_BASE, 16);
if (priv->base == NULL) {
status = -ENOMEM;
goto cleanup0;
}
priv->descs = kmalloc(sizeof(struct delqa_descs), GFP_KERNEL);
if (priv->descs == NULL) {
status = -ENOMEM;
goto cleanup1;
}
dev->mem_start = (unsigned int)priv->descs;
dev->mem_end = (unsigned int)priv->descs + sizeof(*(priv->descs));
/* FIXME: get the vector from the q-bus adapter driver */
write_reg(priv, DELQA_VECTOR, DELQA_QBUS_VECTOR);
priv->qbus_vector = DELQA_QBUS_VECTOR;
printk("delqa qbus vector: %d (0%03o, 0x%04x)\n", priv->qbus_vector, priv->qbus_vector, priv->qbus_vector);
dev->irq = qbus_vector_to_irq(priv->qbus_vector);
printk("Ethernet address in ROM: ");
for (i = 0; i < 6; i++) {
dev->dev_addr[i] = priv->base[i*2] & 0xff;
printk("%2.2x%c", dev->dev_addr[i], i == 5 ? '\n' : ':');
}
/* Here we need to setup qbus mapping registers so that the DELQA
can DMA to and from our buffers */
priv->desc_map = qbus_alloc_mapregs(priv->descs, sizeof(struct delqa_descs));
if (priv->desc_map == NULL) {
status = -ENOMEM;
goto cleanup2;
}
status = init_desc_rings(dev);
if (status < 0) {
goto cleanup3;
}
dev->open = delqa_open;
dev->stop = delqa_close;
dev->hard_start_xmit = delqa_start_xmit;
dev->tx_timeout = delqa_tx_timeout;
dev->watchdog_timeo = 5*HZ;
dev->get_stats = &delqa_get_stats;
dev->set_multicast_list = &delqa_set_multicast;
dev->dma = 0;
ether_setup(dev);
return status;
cleanup3:
qbus_unmap(priv->desc_map);
cleanup2:
kfree(priv->descs);
cleanup1:
iounmap(priv->base);
cleanup0:
kfree(dev->priv);
dev->priv = NULL;
return status;
}
struct net_device delqa_dev = {
init: delqa_init
};
int __init delqa_probe(void)
{
return register_netdev(&delqa_dev);
}
__initcall(delqa_probe);
|
