Update of /cvsroot/linux-mips/linux/arch/mips/au1000/common
In directory usw-pr-cvs1:/tmp/cvs-serv20100/arch/mips/au1000/common
Modified Files:
irq.c
Log Message:
Sync up with oss tree:
* explicitly set polarity of all interrupts
* added pci_auto config option
* updated defconfig file
* moved the au1000 specific tlb handler to tlbex-r4k.S
* updated au1000.h with IrDA registers
Index: irq.c
===================================================================
RCS file: /cvsroot/linux-mips/linux/arch/mips/au1000/common/irq.c,v
retrieving revision 1.8
retrieving revision 1.9
diff -u -d -r1.8 -r1.9
--- irq.c 2001/10/03 22:49:23 1.8
+++ irq.c 2001/10/31 06:16:24 1.9
@@ -388,12 +388,14 @@
for (i = 0; i <= NR_IRQS; i++) {
switch (i) {
- case AU1000_GPIO_15:
- setup_local_irq(i, INTC_INT_LOW_LEVEL, 0);
- irq_desc[i].handler = &level_irq_type;
- break;
- case AU1000_MAC0_DMA_INT:
- case AU1000_MAC1_DMA_INT:
+ case AU1000_UART0_INT:
+ case AU1000_UART1_INT:
+ case AU1000_UART2_INT:
+ case AU1000_UART3_INT:
+
+ case AU1000_SSI0_INT:
+ case AU1000_SSI1_INT:
+
case AU1000_DMA_INT_BASE:
case AU1000_DMA_INT_BASE+1:
case AU1000_DMA_INT_BASE+2:
@@ -402,22 +404,40 @@
case AU1000_DMA_INT_BASE+5:
case AU1000_DMA_INT_BASE+6:
case AU1000_DMA_INT_BASE+7:
+
+ case AU1000_IRDA_TX_INT:
+ case AU1000_IRDA_RX_INT:
+
+ case AU1000_MAC0_DMA_INT:
+ case AU1000_MAC1_DMA_INT:
setup_local_irq(i, INTC_INT_HIGH_LEVEL, 0);
irq_desc[i].handler = &level_irq_type;
break;
+
+ case AU1000_GPIO_15:
case AU1000_USB_HOST_INT:
setup_local_irq(i, INTC_INT_LOW_LEVEL, 0);
irq_desc[i].handler = &level_irq_type;
break;
+ case AU1000_ACSYNC_INT:
+ case AU1000_AC97C_INT:
case AU1000_USB_DEV_REQ_INT:
case AU1000_USB_DEV_SUS_INT:
+ case AU1000_PC0_INT:
+ case AU1000_PC0_MATCH0_INT:
+ case AU1000_PC0_MATCH1_INT:
+ case AU1000_PC1_INT:
+ case AU1000_PC1_MATCH0_INT:
+ case AU1000_PC1_MATCH1_INT:
+ case AU1000_PC1_MATCH2_INT:
setup_local_irq(i, INTC_INT_RISE_EDGE, 0);
irq_desc[i].handler = &rise_edge_irq_type;
break;
+
// Careful if you change match 2 request!
// The interrupt handler is called directly
// from the low level dispatch code.
- case AU1000_PC0_MATCH2_INT:
+ case AU1000_PC0_MATCH2_INT:
setup_local_irq(i, INTC_INT_RISE_EDGE, 1);
irq_desc[i].handler = &rise_edge_irq_type;
break;
|
