[this was meant to go to linux-kernel and fbdev-users at the same time,
but I made a typo. sorry]
After booting 2.6.5-rc1-mm1 with this command-line:
kernel /vmlinuz-265rc1mm1 root=/dev/hda3 video=radeonfb:1600x1200-32@75 acpi=force
I get a warning on my monitor:
fH 271.5 kHz
fV 217.2 Hz
That is obviously not what I meant by 1600x1200-32@75.
fbset -V tells me:
Linux Frame Buffer Device Configuration Version 2.1 (23/06/1999)
(C) Copyright 1995-1999 by Geert Uytterhoeven
mode "1600x1200-75"
# D: 202.511 MHz, H: 93.755 kHz, V: 75.004 Hz
geometry 1600 1200 1600 1200 32
timings 4938 304 64 46 1 192 3
hsync high
vsync high
rgba 8/16,8/8,8/0,0/0
endmode
dmesg:
Console: switching to colour frame buffer device 133x54
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=166.00 Mhz, System=166.00 MHz
radeonfb: No connector info table detected
radeonfb: Monitor 1 type CRT found
radeonfb: ATI Radeon QD DDR SGRAM 64 MB
lspci:
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R100 QD [Radeon 7200] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon 7000/Radeon
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
.config:
CONFIG_FB=y
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
Obviously, it's bad that I define what video-mode I want and radeonfb
starts changing that to bogus values. The monitor is an Eizo F931,
connected via a Rose Electronics Vista KVM.
Any hints on solving this?
Thanks,
Jurriaan
--
Thesaurus (n): ancient reptile with excellent vocabulary.
Debian (Unstable) GNU/Linux 2.6.4-rc1-mm2 3940 bogomips load av: 0.00 0.00 0.00
|
