Menu
▾
▴
Re: [Linux-ATM-General] atm-tools and Ubuntu 10.10 - UPDATE
|
From: chas w. - C. <ch...@cm...> - 2011-01-21 15:29:08
|
you only need atmarpd for clip interfaces. you shouldnt need to run it. On Fri, 21 Jan 2011 11:32:13 +0000 Maestrelli Francesco <fra...@aa...> wrote: > In addition, when I run atmarpd (atmarpd -b) I get the following error: > > atmarpd:IO: ioctl ATMARPD_CTRL: Address already in use > Fatal error - Terminating > > > Francesco Maestrelli > ------------------------------------ > fra...@aa... > > ________________________________________ > From: Maestrelli Francesco [fra...@aa...] > Sent: 21 January 2011 12:20 > To: lin...@li... > Subject: [Linux-ATM-General] atm-tools and Ubuntu 10.10 > > I forgot to add as a CC to my answer the whole mailing list. Sorry for that and for sending again this message. > > Little description: > > I'm trying to configure an ATM connection between a computer I'm setting up and a DSLAM (Nokia D50, former Eksos B20) that will be connected over ADSL to an ADSL modem (M10 ADSL modem). This should simulate the standard conficuration an ISP could use to provide ADSL services to its customers. > > The computer I'm setting up should act as a switch or router and forward the requests coming from the ADSL connection (that the client computer connected to the ADSL modem will send) to the default gateway of the network I'm connected to. To do this the computer also have an ethernet card connected to the local network. > > Problem: > > The computer I'm setting up is running ubuntu 10.10 (kernel 2.6.35-24-generic), 512MB RAM, AMD Athlon Processor 1,4 Ghz. I was looking for information on the net to set up this environment, but i couldn't find much. > I'm actually following this: http://www.linuxjournal.com/article/3005 even if it's a quite old article. > > When I start atmsigd or ilmid the computer suddenly stop responding. > > Since I need to create a connection between this computer and the DSLAM and from there to the modem i think I'll need to setup a PVC thus I don't think I'll need those daemon.. right? What could be the reason they freeze anyway? > > Leaving aside these two I did the following: > > * I created the ATM device name: atmarp -c atm0 > > and from ifconfig -a i see the following: > > atm0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 > [NO FLAGS] MTU:9180 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > (Isn't it weird that HWaddr is all zeros?) > > > * I configured the interface : ifconfig atm0 10.38.100.254 netmask 255.255.255.0 mtu 9180 > > * I added a route for the ATM subnet : route add -net 10.38.100.0 netmask 255.255.255.0 atm0 > > *Now I tried to setup the PVC: atmarp -s 10.38.100.101 0.0.101 (VPI:0 VCI:101) > > now I'm not totally sure about this command, but as I said I can't find much documentation on how do do this. > At this point the pc freezes again. > > > Probably It's my bad that I'm not understanding something. Any help would be precious. Thanks in advance. > > > BR, > > Francesco Maestrelli > ------------------------------------ > fra...@aa... > > ________________________________________ > From: chas williams - CONTRACTOR [ch...@cm...] > Sent: 20 January 2011 17:10 > To: Maestrelli Francesco > Cc: lin...@li... > Subject: Re: [Linux-ATM-General] atm-tools and Ubuntu 10.10 > > nothing that i know about specifically. what is your hardware and what > are commands are you running? > > On Thu, 20 Jan 2011 11:03:59 +0000 > Maestrelli Francesco <fra...@aa...> wrote: > > > Are there know issues with the atm daemons and Ubuntu 10.10? When I l start them following instructions in here http://www.linuxjournal.com/article/3005 the machine freezes. > > > > Thanks > > > > Francesco > > > ------------------------------------------------------------------------------ > Special Offer-- Download ArcSight Logger for FREE (a $49 USD value)! > Finally, a world-class log management solution at an even better price-free! > Download using promo code Free_Logger_4_Dev2Dev. Offer expires > February 28th, so secure your free ArcSight Logger TODAY! > http://p.sf.net/sfu/arcsight-sfd2d > _______________________________________________ > Linux-atm-general mailing list > Lin...@li... > https://lists.sourceforge.net/lists/listinfo/linux-atm-general > > ------------------------------------------------------------------------------ > Special Offer-- Download ArcSight Logger for FREE (a $49 USD value)! > Finally, a world-class log management solution at an even better price-free! > Download using promo code Free_Logger_4_Dev2Dev. Offer expires > February 28th, so secure your free ArcSight Logger TODAY! > http://p.sf.net/sfu/arcsight-sfd2d > _______________________________________________ > Linux-atm-general mailing list > Lin...@li... > https://lists.sourceforge.net/lists/listinfo/linux-atm-general > |
