Re: [Linux-ATM-General] Due for a new release?

[Philip P. <phi...@re...>]

On 12/28/10 9:31 AM, Philip Prindeville wrote:
> On 12/28/10 8:40 AM, chas williams - CONTRACTOR wrote:
>> i have released 2.5.2
> Awesome.  Building now.
>

Well, with:

astlinux, unmodified other than bumping linux-atm to 2.5.2
keeping the experimental firmware on the solos PCI card
and using the solos-0.11 download with the same patches as before

it fails to train up.

...
NET: Registered protocol family 8
NET: Registered protocol family 20
Solos PCI Driver Version 0.11 svn-25
solos 0000:00:0c.0: Solos FPGA Version 0.03 svn-38
solos 0000:00:0c.0: Registered ATM device 0
solos 0000:00:0c.0: Registered ATM device 1
solos 0000:00:0c.0: Port 0: HandShake
Bridge firewalling registered
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
device eth0 entered promiscuous mode
eth1: link down
device eth1 entered promiscuous mode
Bringing up br1 as 192.168.0.2
br1: topology change detected, propagating
br1: port 1(eth0) entering forwarding state
Sleeping for 30 seconds before I bring up ppp0...
Attempting to bring up PPPoA on atm0
This could take some time...
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Starting ppp.............................. timeout!
Pppd timed out waiting for negotiation!


not sure why this would fail.  I'm using PPPoA.  From dmesg:

Device: 0 Vpi: 0 Vci: 32
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
solos 0000:00:0c.0: Port 1: Idle
solos 0000:00:0c.0: Port 1: HandShake
Device: 0 Vpi: 0 Vci: 32
Device: 0 Vpi: 0 Vci: 32
solos 0000:00:0c.0: Port 1: Idle
solos 0000:00:0c.0: Port 0: Idle
solos 0000:00:0c.0: Port 1: HandShake
solos 0000:00:0c.0: Port 0: HandShake
Device: 0 Vpi: 0 Vci: 32
solos 0000:00:0c.0: Port 0: Training
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Port 0: Showtime @1536/896 kb/s, SNR 29.5 dB, Attn 27.5 dB
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
solos 0000:00:0c.0: Received packet for unknown VPI.VCI 0.32 on port 0
Device: 0 Vpi: 0 Vci: 32


If I kill and restart pppd it works.