Re: [Isisalsa-devel] [Re: isis driver]
Status: Inactive
Brought to you by:
jeanseb
Menu
▾
▴
Re: [Isisalsa-devel] [Re: isis driver]
|
From: Felipe S. <sol...@es...> - 2003-08-18 05:08:39
|
Felipe Sologuren wrote:
> -------- Original Message --------
> Subject: Re: isis driver
> Date: Sat, 16 Aug 2003 13:11:32 -0400
> From: Felipe Sologuren <sol...@es...>
> To: ppalmers <Pie...@es...>
> References: <3F3...@es...>
> <3F3...@es...>
> <106...@we...>
>
> ppalmers wrote:
>
>>> Cold reboot from windows is still necessary for maxiinit not?
>>>
>>
>>
>> windows boot is not nescessary. On my system, everything works without
>> windows boot.
>>
>>
>>
> Pieter:
> Yesterday, I could listen audio in XMMS with snd-es1968 (the sound
> was good) but with snd-isis module the error is the same ('ALSA
> sam_io.c:345: sam9407: command 0x3 ack timeout...').
> I don't know if it could be an irq problem.
> It could be a problem with my chipset VIA KT333 & VT8235 yet?
> The card is in the slot 5 of pci bus and the onboard sound is disabled.
> In bios, for settings, this slot have the same irq (5) with slot 2 (empty).
> I have RH7.3 again with kernel 2.4.18-3 and gcc 2.96.
> I think that in RH9 (not upgraded and in other partition) with kernel
> 2.4.20-8 and gcc 3.2 the result will be the same, I'll do the test
> tomorrow.
Effectively snd-es1968 works in RH9 and snd-isis doesn't load.
Somebody have an idea about this?
>
> In Via website exist a patch for ide timings. For 'time.h' of kernel
> sources. It could help?
>
> Thank you one more time,
> Felipe
>
>
> ------------------------------------------------------------------------
>
> 00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
> Subsystem: VIA Technologies, Inc.: Unknown device 0000
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 8
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=32M]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Memory behind bridge: dde00000-dfefffff
> Prefetchable memory behind bridge: d9d00000-ddcfffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:08.0 Multimedia audio controller: ESS Technology ES1978 Maestro 2E (rev 10)
> Subsystem: Guillemot Corporation: Unknown device 0010
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 6000ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: I/O ports at ec00 [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0a.0 Ethernet controller: Davicom Semiconductor, Inc. Ethernet 100/10 MBit (rev 31)
> Subsystem: Unknown device 3030:5032
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (5000ns min, 10000ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at e800 [size=256]
> Region 1: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at dff80000 [disabled] [size=256K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3177
> Subsystem: VIA Technologies, Inc.: Unknown device 0000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
> Subsystem: Micro-star International Co Ltd: Unknown device 7120
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin A routed to IRQ 14
> Region 4: I/O ports at fc00 [size=16]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta] (rev 15) (prog-if 00 [VGA])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at da000000 (32-bit, prefetchable) [size=32M]
> Expansion ROM at dfef0000 [disabled] [size=64K]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
> Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
>
>
> ------------------------------------------------------------------------
>
> Linux version 2.4.18-3 (bhc...@po...) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 Thu Apr 18 07:32:41 EDT 2002
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> found SMP MP-table at 000fb930
> hm, page 000fb000 reserved twice.
> hm, page 000fc000 reserved twice.
> hm, page 000f6000 reserved twice.
> hm, page 000f7000 reserved twice.
> On node 0 totalpages: 65536
> zone(0): 4096 pages.
> zone(1): 61440 pages.
> zone(2): 0 pages.
> Intel MultiProcessor Specification v1.1
> Virtual Wire compatibility mode.
> OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000
> Processor #0 Pentium(tm) Pro APIC version 17
> I/O APIC #2 Version 3 at 0xFEC00000.
> Processors: 1
> Kernel command line: ro root=/dev/hda4 hdd=ide-scsi
> ide_setup: hdd=ide-scsi
> Initializing CPU#0
> Detected 950.043 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 1893.99 BogoMIPS
> Memory: 255384k/262144k available (1125k kernel code, 6372k reserved, 802k data, 296k init, 0k highmem)
> Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
> Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
> Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
> Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
> Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
> CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
> CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
> CPU: AMD Athlon(tm) Processor stepping 02
> Enabling fast FPU save and restore... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.40 (20010327) Richard Gooch (rg...@at...)
> mtrr: detected mtrr type: Intel
> PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> PCI: Using IRQ router default [1106/3177] at 00:11.0
> PCI: Hardcoded IRQ 14 for device 00:11.1
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
> Starting kswapd
> VFS: Diskquotas version dquot_6.5.0 initialized
> pty: 2048 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
> Real Time Clock Driver v1.10e
> block: 496 slots per queue, batch=124
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 89
> PCI: Hardcoded IRQ 14 for device 00:11.1
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: Unknown VIA SouthBridge, contact Vojtech Pavlik <vo...@su...>
> hda: MAXTOR 6L040J2, ATA DISK drive
> hdc: QUANTUM FIREBALLlct10 10, ATA DISK drive
> hdd: HL-DT-ST GCE-8400B, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide0: probed IRQ 14 failed, using default.
> ide1 at 0x170-0x177,0x376 on irq 15
> ide1: probed IRQ 15 failed, using default.
> hda: 78177792 sectors (40027 MB) w/1818KiB Cache, CHS=4866/255/63
> hdc: 20044080 sectors (10263 MB) w/418KiB Cache, CHS=19885/16/63
> ide-floppy driver 0.99.newide
> Partition check:
> hda: hda1 hda2 hda3 hda4
> hdc: [PTBL] [1247/255/63] hdc1 hdc2
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> ide-floppy driver 0.99.newide
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 2048 buckets, 16Kbytes
> TCP: Hash tables configured (established 16384 bind 16384)
> Linux IP multicast router 0.06 plus PIM-SM
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> RAMDISK: Compressed image found at block 0
> Freeing initrd memory: 152k freed
> VFS: Mounted root (ext2 filesystem).
> reiserfs: checking transaction log (device 03:04) ...
> Using r5 hash to sort names
> ReiserFS version 3.6.25
> Freeing unused kernel memory: 296k freed
> Adding Swap: 506036k swap-space (priority -1)
> Adding Swap: 522104k swap-space (priority -2)
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: HL-DT-ST Model: CD-RW GCE-8400B Rev: 1.01
> Type: CD-ROM ANSI SCSI revision: 02
> parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
> parport0: irq 7 detected
> ip_conntrack (2048 buckets, 16384 max)
> 0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4363 Sat Apr 19 17:46:46 PDT 2003
> Linux agpgart interface v0.99 (c) Jeff Hartmann
> agpgart: Maximum main memory to use for agp memory: 204M
> agpgart: Detected Via Apollo Pro KT266 chipset
> agpgart: AGP aperture is 32M @ 0xe0000000
> Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.12
> isis: loading driver built on 01:56:25 Aug 14 2003
> ALSA isis.c:2632: Entering ISIS create
> ALSA isis.c:2822: isis: loading SAM driver
> ALSA sam9407.c:27: sam9407: Creating chip
> ALSA sam_pcm.c:937: creating 1/2 controls
> ALSA sam_pcm.c:975: creating 3/4 controls
> ALSA sam_ucode.c:324: new HWDEP
> ALSA sam_mpu401.c:305: creating MIDI controls
> ALSA sam9407.c:121: sam9407: Creating chip done
> ALSA sam9407.c:154: sam9407: Init chip
> ALSA sam_io.c:345: sam9407: command 0x3 ack timeout
> ALSA sam_io.c:345: sam9407: command 0x2 ack timeout
> ALSA sam_mem.c:128: sam9407: transfer 192 words from address 0x0 failed
> ALSA isis.c:2215: isis: Error creating SAM chip
> ALSA sam9407.c:327: sam9407: devfree chip
> ALSA sam9407.c:285: sam9407: free chip
> ALSA sam9407.c:268: sam9407: cleanup shadows
> Maxi Studio ISIS soundcard not found or device busy
> isis: loading driver built on 01:56:25 Aug 14 2003
> ALSA isis.c:2632: Entering ISIS create
> ALSA isis.c:2822: isis: loading SAM driver
> ALSA sam9407.c:27: sam9407: Creating chip
> ALSA sam_pcm.c:937: creating 1/2 controls
> ALSA sam_pcm.c:975: creating 3/4 controls
> ALSA sam_ucode.c:324: new HWDEP
> ALSA sam_mpu401.c:305: creating MIDI controls
> ALSA sam9407.c:121: sam9407: Creating chip done
> ALSA sam9407.c:154: sam9407: Init chip
> ALSA sam_io.c:345: sam9407: command 0x3 ack timeout
> ALSA sam_io.c:345: sam9407: command 0x2 ack timeout
> ALSA sam_mem.c:128: sam9407: transfer 192 words from address 0x0 failed
> ALSA isis.c:2215: isis: Error creating SAM chip
> ALSA sam9407.c:327: sam9407: devfree chip
> ALSA sam9407.c:285: sam9407: free chip
> ALSA sam9407.c:268: sam9407: cleanup shadows
> Maxi Studio ISIS soundcard not found or device busy
> isis: loading driver built on 01:56:25 Aug 14 2003
> ALSA isis.c:2632: Entering ISIS create
> ALSA isis.c:2822: isis: loading SAM driver
> ALSA sam9407.c:27: sam9407: Creating chip
> ALSA sam_pcm.c:937: creating 1/2 controls
> ALSA sam_pcm.c:975: creating 3/4 controls
> ALSA sam_ucode.c:324: new HWDEP
> ALSA sam_mpu401.c:305: creating MIDI controls
> ALSA sam9407.c:121: sam9407: Creating chip done
> ALSA sam9407.c:154: sam9407: Init chip
> ALSA sam_io.c:345: sam9407: command 0x3 ack timeout
> ALSA sam_io.c:345: sam9407: command 0x2 ack timeout
> ALSA sam_mem.c:128: sam9407: transfer 192 words from address 0x0 failed
> ALSA isis.c:2215: isis: Error creating SAM chip
> ALSA sam9407.c:327: sam9407: devfree chip
> ALSA sam9407.c:285: sam9407: free chip
> ALSA sam9407.c:268: sam9407: cleanup shadows
> Maxi Studio ISIS soundcard not found or device busy
|
