I had a working hylafax/iaxmodem/asterisk installation. It worked for
years. Then I decided to upgrade.
I use debian wheezy amd64.
Asterisk 1.8.13.1
IAXModem 1.2.0
Hylafax 6.0.6-5
Now I get this Error (tried with different numbers I know different
hardware is behind):
Your job to 073xxxxxxx failed because:
DIS/DTC received 3 times; DCS not recognized; Giving up after 3 attempts to send same page
I played with jitterbuffer, alaw ulaw slinear codecs and much more, but I do not get one silly fax out.
I had a working hylafax/iaxmodem/asterisk installation. It worked for
years. Then I decided to upgrade.
I use debian wheezy amd64.
Asterisk 1.8.13.1
IAXModem 1.2.0
Hylafax 6.0.6-5
What were these before the upgrade? What else changed? Hardware?
Network? What DAHDI interface are you using to the PSTN?
Thanks,
Lee.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
What were these before the upgrade? What else changed? Hardware?
Network? What DAHDI interface are you using to the PSTN?
Thanks,
Lee.
Hi Lee,
I had to revert to 0.1.16 as described in another post.
But i still have 1.2.0 installed as iaxmodem, 0.1.16 as iaxmodemold
executable.
So one can quickly switch.
Are you interested in getting acces over ssh?
Aksels
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
What were these before the upgrade? What else changed?
Hardware?
Network? What DAHDI interface are you using to the PSTN?
Thanks,
Lee.
Hi Lee,
I had to revert to 0.1.16 as described in another post.
But i still have 1.2.0 installed as iaxmodem, 0.1.16 as iaxmodemold
executable.
So one can quickly switch.
Are you interested in getting acces over ssh?
Aksels
I have an interest in knowing what is wrong and seeing that the problem
be resolved. However, I don't have the time to determine the problem,
myself, and my gut feeling is that you're dealing with a problem that is
specific to your system or your environment, and in that case if you've
found a solution for yourself then I think you should stick with it.
Thanks,
Lee.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi.
I had a working hylafax/iaxmodem/asterisk installation. It worked for
years. Then I decided to upgrade.
I use debian wheezy amd64.
Asterisk 1.8.13.1
IAXModem 1.2.0
Hylafax 6.0.6-5
Now I get this Error (tried with different numbers I know different
hardware is behind):
Your job to 073xxxxxxx failed because:
DIS/DTC received 3 times; DCS not recognized; Giving up after 3 attempts to send same page
I played with jitterbuffer, alaw ulaw slinear codecs and much more, but I do not get one silly fax out.
Could anybody please help me?
/etc/iaxmodem/ttyIAX0
device /dev/ttyIAX0
owner uucp:uucp
mode 660
port 4570
refresh 300
server 127.0.0.1
peername iaxmodem
secret password
codec slinear
;codec ulaw
nojitterbuffer
/etc/hylafax/config.ttyIAX0
Just plain standard from examples with Phonnumbers edited.
/etc/asterisk/iax.conf
[general]
bind = 127.0.0.1
[iaxmodem]
type = friend
secret = password
port = 4570
host = dynamic
context = fax-out
disallow = all
allow = slinear
allow = alaw
allow = ulaw
requirecalltoken=no
---- Transcript of session follows ----
Apr 16 08:55:20.09: [ 6766]: SESSION BEGIN 000000166 4973xxxx
Apr 16 08:55:20.10: [ 6766]: HylaFAX (tm) Version 6.0.6
Apr 16 08:55:20.10: [ 6766]: SEND FAX: JOB 20 DEST 073xxxxxx COMMID 000000166 DEVICE '/dev/ttyIAX0' FROM 'root' USER root
Apr 16 08:55:20.10: [ 6766]: STATE CHANGE: RUNNING -> SENDING
Apr 16 08:55:20.10: [ 6766]: <-- [12:AT+FCLASS=1\r]
Apr 16 08:55:20.10: [ 6766]: --> [2:OK]
Apr 16 08:55:20.10: [ 6766]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Apr 16 08:55:20.10: [ 6766]: DIAL 073xxxxxx
Apr 16 08:55:20.10: [ 6766]: <-- [17:ATDT073xxxxx\r]
Apr 16 08:55:28.69: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:30.22: [ 6766]: --> HDLC<25:FF C0 02 AC 0C 1C 8C 2C 4C 9C 6C 0C CC EC 9C 2C D4 04 04 04 04 04 04 6D 22>
Apr 16 08:55:30.22: [ 6766]: --> [2:OK]
Apr 16 08:55:30.22: [ 6766]: REMOTE CSI "+4973xxxx"
Apr 16 08:55:30.22: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:30.65: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:30.65: [ 6766]: --> HDLC<15:FF C8 01 00 77 1F 23 01 01 01 01 01 00 A3 3B>
Apr 16 08:55:30.70: [ 6766]: --> [2:OK]
Apr 16 08:55:30.70: [ 6766]: REMOTE best rate 14400 bit/s
Apr 16 08:55:30.70: [ 6766]: REMOTE max A4 page width (215 mm)
Apr 16 08:55:30.70: [ 6766]: REMOTE max unlimited page length
Apr 16 08:55:30.70: [ 6766]: REMOTE best vres 7.7 line/mm
Apr 16 08:55:30.70: [ 6766]: REMOTE format support: MH, MR, MMR
Apr 16 08:55:30.70: [ 6766]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 16 08:55:30.70: [ 6766]: REMOTE best 0 ms/scanline
Apr 16 08:55:30.70: [ 6766]: USE 14400 bit/s
Apr 16 08:55:30.70: [ 6766]: USE error correction mode
Apr 16 08:55:30.70: [ 6766]: SEND file "docq/doc20.ps;c0"
Apr 16 08:55:30.70: [ 6766]: USE A4 page width (215 mm)
Apr 16 08:55:30.70: [ 6766]: USE unlimited page length
Apr 16 08:55:30.70: [ 6766]: USE 3.85 line/mm
Apr 16 08:55:30.70: [ 6766]: USE 2-D MMR
Apr 16 08:55:30.70: [ 6766]: USE 0 ms/scanline
Apr 16 08:55:30.70: [ 6766]: SEND training at v.17 14400 bit/s
Apr 16 08:55:30.70: [ 6766]: <-- [9:AT+FRS=7\r]
Apr 16 08:55:30.77: [ 6766]: --> [2:OK]
Apr 16 08:55:30.77: [ 6766]: <-- [9:AT+FTH=3\r]
Apr 16 08:55:30.79: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:30.79: [ 6766]: <-- HDLC<23:FF C0 C2 76 A6 E6 76 96 4E 16 A6 F6 6A 04 12 46 B6 E2 04 76 76 86 EA>
Apr 16 08:55:30.79: [ 6766]: <-- data [23]
Apr 16 08:55:30.79: [ 6766]: <-- data [2]
Apr 16 08:55:32.13: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:32.13: [ 6766]: <-- HDLC<7:FF C8 C1 00 44 1F 22>
Apr 16 08:55:32.13: [ 6766]: <-- data [7]
Apr 16 08:55:32.13: [ 6766]: <-- data [2]
Apr 16 08:55:32.47: [ 6766]: --> [2:OK]
Apr 16 08:55:32.47: [ 6766]: <-- [9:AT+FTS=7\r]
Apr 16 08:55:32.54: [ 6766]: --> [2:OK]
Apr 16 08:55:32.54: [ 6766]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Apr 16 08:55:32.54: [ 6766]: <-- [11:AT+FTM=145\r]
Apr 16 08:55:32.54: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:32.54: [ 6766]: DELAY 400 ms
Apr 16 08:55:32.94: [ 6766]: <-- data [1024]
Apr 16 08:55:32.94: [ 6766]: <-- data [1024]
Apr 16 08:55:32.94: [ 6766]: <-- data [652]
Apr 16 08:55:32.94: [ 6766]: <-- data [2]
Apr 16 08:55:34.99: [ 6766]: --> [2:OK]
Apr 16 08:55:34.99: [ 6766]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Apr 16 08:55:34.99: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:36.76: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:38.29: [ 6766]: --> HDLC<25:FF C0 02 AC 0C 1C 8C 2C 4C 9C 6C 0C CC EC 9C 2C D4 04 04 04 04 04 04 6D 22>
Apr 16 08:55:38.29: [ 6766]: --> [2:OK]
Apr 16 08:55:38.29: [ 6766]: REMOTE CSI "+4973xxxxxx"
Apr 16 08:55:38.29: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:38.73: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:38.73: [ 6766]: --> HDLC<15:FF C8 01 00 77 1F 23 01 01 01 01 01 00 A3 3B>
Apr 16 08:55:38.77: [ 6766]: --> [2:OK]
Apr 16 08:55:38.77: [ 6766]: SEND training at v.17 14400 bit/s
Apr 16 08:55:38.77: [ 6766]: <-- [9:AT+FRS=7\r]
Apr 16 08:55:38.83: [ 6766]: --> [2:OK]
Apr 16 08:55:38.83: [ 6766]: <-- [9:AT+FTH=3\r]
Apr 16 08:55:38.85: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:38.85: [ 6766]: <-- HDLC<23:FF C0 C2 76 A6 E6 76 96 4E 16 A6 F6 6A 04 12 46 B6 E2 04 76 76 86 EA>
Apr 16 08:55:38.85: [ 6766]: <-- data [23]
Apr 16 08:55:38.85: [ 6766]: <-- data [2]
Apr 16 08:55:39.99: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:39.99: [ 6766]: <-- HDLC<7:FF C8 C1 00 44 1F 22>
Apr 16 08:55:39.99: [ 6766]: <-- data [7]
Apr 16 08:55:39.99: [ 6766]: <-- data [2]
Apr 16 08:55:40.28: [ 6766]: --> [2:OK]
Apr 16 08:55:40.28: [ 6766]: <-- [9:AT+FTS=7\r]
Apr 16 08:55:40.34: [ 6766]: --> [2:OK]
Apr 16 08:55:40.34: [ 6766]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Apr 16 08:55:40.34: [ 6766]: <-- [11:AT+FTM=145\r]
Apr 16 08:55:40.34: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:40.34: [ 6766]: DELAY 400 ms
Apr 16 08:55:40.74: [ 6766]: <-- data [1024]
Apr 16 08:55:40.74: [ 6766]: <-- data [1024]
Apr 16 08:55:40.74: [ 6766]: <-- data [652]
Apr 16 08:55:40.74: [ 6766]: <-- data [2]
Apr 16 08:55:42.46: [ 6766]: --> [2:OK]
Apr 16 08:55:42.46: [ 6766]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Apr 16 08:55:42.46: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:44.83: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:46.36: [ 6766]: --> HDLC<25:FF C0 02 AC 0C 1C 8C 2C 4C 9C 6C 0C CC EC 9C 2C D4 04 04 04 04 04 04 6D 22>
Apr 16 08:55:46.36: [ 6766]: --> [2:OK]
Apr 16 08:55:46.36: [ 6766]: REMOTE CSI "+4973xxxxx"
Apr 16 08:55:46.36: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:46.80: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:46.80: [ 6766]: --> HDLC<15:FF C8 01 00 77 1F 23 01 01 01 01 01 00 A3 3B>
Apr 16 08:55:46.84: [ 6766]: --> [2:OK]
Apr 16 08:55:46.84: [ 6766]: SEND training at v.17 14400 bit/s
Apr 16 08:55:46.84: [ 6766]: <-- [9:AT+FRS=7\r]
Apr 16 08:55:46.91: [ 6766]: --> [2:OK]
Apr 16 08:55:46.91: [ 6766]: <-- [9:AT+FTH=3\r]
Apr 16 08:55:46.92: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:46.92: [ 6766]: <-- HDLC<23:FF C0 C2 76 A6 E6 76 96 4E 16 A6 F6 6A 04 12 46 B6 E2 04 76 76 86 EA>
Apr 16 08:55:46.92: [ 6766]: <-- data [23]
Apr 16 08:55:46.92: [ 6766]: <-- data [2]
Apr 16 08:55:47.90: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:47.90: [ 6766]: <-- HDLC<7:FF C8 C1 00 44 1F 22>
Apr 16 08:55:47.90: [ 6766]: <-- data [7]
Apr 16 08:55:47.90: [ 6766]: <-- data [2]
Apr 16 08:55:48.16: [ 6766]: --> [2:OK]
Apr 16 08:55:48.16: [ 6766]: <-- [9:AT+FTS=7\r]
Apr 16 08:55:48.21: [ 6766]: --> [2:OK]
Apr 16 08:55:48.21: [ 6766]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Apr 16 08:55:48.21: [ 6766]: <-- [11:AT+FTM=145\r]
Apr 16 08:55:48.21: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:48.21: [ 6766]: DELAY 400 ms
Apr 16 08:55:48.61: [ 6766]: <-- data [1024]
Apr 16 08:55:48.61: [ 6766]: <-- data [1024]
Apr 16 08:55:48.61: [ 6766]: <-- data [652]
Apr 16 08:55:48.61: [ 6766]: <-- data [2]
Apr 16 08:55:50.04: [ 6766]: --> [2:OK]
Apr 16 08:55:50.04: [ 6766]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Apr 16 08:55:50.04: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:52.90: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:54.43: [ 6766]: --> HDLC<25:FF C0 02 AC 0C 1C 8C 2C 4C 9C 6C 0C CC EC 9C 2C D4 04 04 04 04 04 04 6D 22>
Apr 16 08:55:54.43: [ 6766]: --> [2:OK]
Apr 16 08:55:54.43: [ 6766]: REMOTE CSI "+4973xxxxx"
Apr 16 08:55:54.43: [ 6766]: <-- [9:AT+FRH=3\r]
Apr 16 08:55:54.87: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:54.87: [ 6766]: --> HDLC<15:FF C8 01 00 77 1F 23 01 01 01 01 01 00 A3 3B>
Apr 16 08:55:54.91: [ 6766]: --> [2:OK]
Apr 16 08:55:54.91: [ 6766]: DIS/DTC received 3 times; DCS not recognized
Apr 16 08:55:54.91: [ 6766]: SEND: Giving up after 3 attempts to send same page "docq/doc20.ps;c0", dirnum 0
Apr 16 08:55:54.91: [ 6766]: <-- [9:AT+FRS=7\r]
Apr 16 08:55:54.98: [ 6766]: --> [2:OK]
Apr 16 08:55:54.98: [ 6766]: <-- [9:AT+FTH=3\r]
Apr 16 08:55:54.99: [ 6766]: --> [7:CONNECT]
Apr 16 08:55:54.99: [ 6766]: <-- HDLC<3:FF C8 DF>
Apr 16 08:55:54.99: [ 6766]: <-- data [3]
Apr 16 08:55:54.99: [ 6766]: <-- data [2]
Apr 16 08:55:55.59: [ 6766]: --> [2:OK]
Apr 16 08:55:55.59: [ 6766]: MODEM input buffering enabled
Apr 16 08:55:56.59: [ 6766]: <-- [5:ATH0\r]
Apr 16 08:55:56.69: [ 6766]: --> [2:OK]
Apr 16 08:55:56.69: [ 6766]: MODEM set DTR OFF
Apr 16 08:55:56.69: [ 6766]: MODEM set baud rate: 0 baud (flow control unchanged)
Apr 16 08:55:56.69: [ 6766]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Apr 16 08:55:56.69: [ 6766]: SESSION END
------- Unsent job status -------
Destination: 073xxxxxx
JobID: 20
GroupID: 20
Sender: root
Mailaddr:root
CommID: 000000166
Modem: any
Submitted From: localhost
Page Width: 209 (mm)
Page Length: 296 (mm)
Resolution: 98 (lpi)
Status: DIS/DTC received 3 times; DCS not recognized; Giving up after 3 attempts to send same page
Dialogs: 3
Dials: 0
Calls: 3
Pages: 0
TotPages: 1
Attempts: 3
Dirnum:
--
Mit freundlichem Gruß,
Axel
On 04/16/2013 12:35 AM, Aksels wrote:
What were these before the upgrade? What else changed? Hardware?
Network? What DAHDI interface are you using to the PSTN?
Thanks,
Lee.
Lee wrote:
Hi Lee,
I had to revert to 0.1.16 as described in another post.
But i still have 1.2.0 installed as iaxmodem, 0.1.16 as iaxmodemold
executable.
So one can quickly switch.
Are you interested in getting acces over ssh?
Aksels
On 04/17/2013 01:08 PM, Aksels wrote:
I have an interest in knowing what is wrong and seeing that the problem
be resolved. However, I don't have the time to determine the problem,
myself, and my gut feeling is that you're dealing with a problem that is
specific to your system or your environment, and in that case if you've
found a solution for yourself then I think you should stick with it.
Thanks,
Lee.