I'm using Hylafax 4.3.3 and Iaxmodem 1.2 and asterisk 1.4.25 and i succeed to receive incomming fax with noproblem but evry time i want to send fax with more than one page i got a problem
here is my config files
more /etc/iaxmodem/iaxmodem-cfg.ttyIAX2
device /dev/ttyIAX2
owner uucp:uucp
mode 660
port 4569
refresh 60
server 127.0.0.1
peername 3001
secret 381250
cidname Kkot
cidnumber +33412385081
codec alaw
more /etc/hylafax/etc/config.ttyIAX2
CountryCode: 33
AreaCode: 4
FAXNumber: +33412385081
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0xFFF
SessionTracing: 0xFFF
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Kalori"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#
# Enabling this will use the hfaxd-protocol to set Caller*ID
#
ModemSetOriginCmd: AT+VSID="%s","%d"
#
# If "glare" during initialization becomes a problem then take
# the modem off-hook during initialization, and then place it
# back on-hook when done.
#
ModemResetCmds: "ATH1\nAT+VCID=1" # enables CallID display
ModemReadyCmds: ATH0
#
# If you are "missing" Caller*ID data on some calls (but not all)
# and if you do not have adequate glare protection you may want to
# not answer based on RINGs, but rather enable the CallIDAnswerLength
# for NDID, disable AT+VCID=1 and do this:
#
#RingsBeforeAnswer: 0
#ModemRingResponse: AT+VRID=1
CallIDPattern: "NMBR="
CallIDPattern: "NAME="
CallIDPattern: "ANID="
CallIDPattern: "NDID="
#CallIDAnswerLength: 4
# Uncomment these if you really want them, but you probably don't.
#CallIDPattern: "DATE="
#CallIDPattern: "TIME="
Hello,
I'm using Hylafax 4.3.3 and Iaxmodem 1.2 and asterisk 1.4.25 and i succeed to receive incomming fax with noproblem but evry time i want to send fax with more than one page i got a problem
here is my config files
more /etc/iaxmodem/iaxmodem-cfg.ttyIAX2
device /dev/ttyIAX2
owner uucp:uucp
mode 660
port 4569
refresh 60
server 127.0.0.1
peername 3001
secret 381250
cidname Kkot
cidnumber +33412385081
codec alaw
more /etc/hylafax/etc/config.ttyIAX2
CountryCode: 33
AreaCode: 4
FAXNumber: +33412385081
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0xFFF
SessionTracing: 0xFFF
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "Kalori"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 200
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#
# Enabling this will use the hfaxd-protocol to set Caller*ID
#
ModemSetOriginCmd: AT+VSID="%s","%d"
#
# If "glare" during initialization becomes a problem then take
# the modem off-hook during initialization, and then place it
# back on-hook when done.
#
ModemResetCmds: "ATH1\nAT+VCID=1" # enables CallID display
ModemReadyCmds: ATH0
Class1AdaptRecvCmd: AT+FAR=1
Class1TMConnectDelay: 400 # counteract quick CONNECT response
Class1RMQueryCmd: "!24,48,72,96" # enable this to disable V.17 receiving
Class1TMQueryCmd: "!24,48,72,96" # enable this to disable V.17 sending
#
# You'll likely want Caller*ID display (also displays DID) enabled.
#
ModemResetCmds: AT+VCID=1 # enables CallID display
#
# If you are "missing" Caller*ID data on some calls (but not all)
# and if you do not have adequate glare protection you may want to
# not answer based on RINGs, but rather enable the CallIDAnswerLength
# for NDID, disable AT+VCID=1 and do this:
#
#RingsBeforeAnswer: 0
#ModemRingResponse: AT+VRID=1
CallIDPattern: "NMBR="
CallIDPattern: "NAME="
CallIDPattern: "ANID="
CallIDPattern: "NDID="
#CallIDAnswerLength: 4
# Uncomment these if you really want them, but you probably don't.
#CallIDPattern: "DATE="
#CallIDPattern: "TIME="
To dialout i'm using mISDN
Here is fax log
SESSION BEGIN 000000817 33958610736
jui 19 18:32:19.99: : HylaFAX ™ Version 4.3.3
jui 19 18:32:19.99: : SEND FAX: JOB 67 DEST 0958610736 COMMID 000000817 DEVICE '/dev/ttyIAX1' FROM 'root <root@ipbx.digibox.net>' USER root
jui 19 18:32:19.99: : STATE CHANGE: RUNNING -> SENDING
jui 19 18:32:19.99: : <-
jui 19 18:32:19.99: : ->
jui 19 18:32:19.99: : MODEM set XON/XOFF/FLUSH: input ignored, output disabled
jui 19 18:32:20.00: : DIAL 0958610736
jui 19 18:32:20.00: : <-
jui 19 18:32:26.66: : ->
jui 19 18:32:28.06: : -> HDLC<25:FF C0 02 6C CC EC 0C 8C 6C 1C AC 9C 0C 04 1E 86 62 A6 A6 4E 62 04 04 CA 5A>
jui 19 18:32:28.06: : ->
jui 19 18:32:28.06: : REMOTE CSI "FreeFax 0958610736"
jui 19 18:32:28.06: : <-
jui 19 18:32:28.53: : ->
jui 19 18:32:28.53: : -> HDLC<15:FF C8 01 00 73 5F 01 01 A9 01 01 01 18 7C 61>
jui 19 18:32:28.59: : ->
jui 19 18:32:28.59: : REMOTE best rate 9600 bit/s
jui 19 18:32:28.59: : REMOTE max A3 page width (303 mm)
jui 19 18:32:28.59: : REMOTE max unlimited page length
jui 19 18:32:28.59: : REMOTE best vres R16 x 15.4 line/mm
jui 19 18:32:28.59: : REMOTE format support: MH, MR
jui 19 18:32:28.59: : REMOTE best 0 ms/scanline
jui 19 18:32:28.59: : USE 9600 bit/s
jui 19 18:32:28.59: : SEND file "docq/doc66.tif;c1"
jui 19 18:32:28.59: : USE A4 page width (215 mm)
jui 19 18:32:28.59: : USE unlimited page length
jui 19 18:32:28.59: : USE 7.7 line/mm
jui 19 18:32:28.60: : USE 2-D MR
jui 19 18:32:28.60: : USE 0 ms/scanline
jui 19 18:32:28.60: : SEND training at v.29 9600 bit/s
jui 19 18:32:28.60: : <-
jui 19 18:32:28.65: : ->
jui 19 18:32:28.65: : <-
jui 19 18:32:28.67: : ->
jui 19 18:32:28.67: : <- HDLC<23:FF C0 C2 96 4E F6 36 86 D6 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
jui 19 18:32:28.67: : <- data
jui 19 18:32:28.67: : <- data
jui 19 18:32:30.18: : ->
jui 19 18:32:30.18: : <- HDLC<6:FF C8 C1 00 63 1E>
jui 19 18:32:30.18: : <- data
jui 19 18:32:30.18: : <- data
jui 19 18:32:30.54: : ->
jui 19 18:32:30.54: : <-
jui 19 18:32:30.63: : ->
jui 19 18:32:30.63: : MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
jui 19 18:32:30.63: : <-
jui 19 18:32:30.65: : ->
jui 19 18:32:30.65: : DELAY 400 ms
jui 19 18:32:31.05: : <- data
jui 19 18:32:31.05: : <- data
jui 19 18:32:31.05: : <- data
jui 19 18:32:32.54: : ->
jui 19 18:32:32.54: : MODEM set XON/XOFF/DRAIN: input ignored, output disabled
jui 19 18:32:32.54: : <-
jui 19 18:32:33.05: : ->
jui 19 18:32:33.96: : -> HDLC<5:FF C8 21 57 BE>
jui 19 18:32:34.02: : ->
jui 19 18:32:34.02: : TRAINING succeeded
jui 19 18:32:34.02: : <-
jui 19 18:32:34.09: : ->
jui 19 18:32:34.09: : <-
jui 19 18:32:34.11: : ->
jui 19 18:32:34.11: : DELAY 400 ms
jui 19 18:32:34.51: : MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
jui 19 18:32:34.51: : SEND begin page
jui 19 18:32:34.56: : Reading MMR-compressed image file
jui 19 18:32:34.61: : <- data
jui 19 18:32:34.61: : <- data
jui 19 18:32:34.61: : <- data
jui 19 18:32:34.61: : <- data
jui 19 18:32:35.43: : <- data
jui 19 18:32:35.43: : <- data
jui 19 18:32:35.43: : <- data
jui 19 18:32:35.43: : <- data
jui 19 18:32:38.73: : <- data
jui 19 18:32:38.73: : <- data
jui 19 18:32:38.73: : <- data
jui 19 18:32:38.73: : <- data
jui 19 18:32:42.02: : <- data
jui 19 18:32:42.02: : <- data
jui 19 18:32:42.02: : <- data
jui 19 18:32:42.02: : <- data
jui 19 18:32:45.28: : <- data
jui 19 18:32:45.28: : <- data
jui 19 18:32:45.28: : <- data
jui 19 18:32:45.28: : <- data
jui 19 18:32:48.51: : <- data
jui 19 18:32:48.52: : <- data
jui 19 18:32:48.52: : <- data
jui 19 18:32:48.52: : <- data
jui 19 18:32:51.73: : <- data
jui 19 18:32:51.73: : <- data
jui 19 18:32:51.73: : <- data
jui 19 18:32:51.73: : <- data
jui 19 18:32:54.91: : <- data
jui 19 18:32:54.91: : <- data
jui 19 18:32:54.92: : <- data
jui 19 18:32:54.92: : <- data
jui 19 18:32:54.92: : SENT 32453 bytes of data
jui 19 18:32:54.92: : SEND 2D RTC
jui 19 18:32:54.92: : <- data
jui 19 18:32:54.92: : <- data
jui 19 18:32:54.92: : SEND end page
jui 19 18:32:59.96: : ->
jui 19 18:32:59.96: : MODEM set XON/XOFF/DRAIN: input ignored, output disabled
jui 19 18:32:59.96: : <-
jui 19 18:33:00.05: : ->
jui 19 18:33:00.05: : SEND send MPS (more pages, same document)
jui 19 18:33:00.05: : <-
jui 19 18:33:00.06: : ->
jui 19 18:33:00.06: : <- HDLC<3:FF C8 F2>
jui 19 18:33:00.06: : <- data
jui 19 18:33:00.06: : <- data
jui 19 18:33:01.04: : ->
jui 19 18:33:01.04: : <-
jui 19 18:33:04.15: : ->
jui 19 18:33:04.15: : MODEM <Empty line>
jui 19 18:33:04.15: : MODEM TIMEOUT: waiting for v.21 carrier
jui 19 18:33:04.15: : <- data
jui 19 18:33:04.15: : ->
jui 19 18:33:04.15: : SEND send MPS (more pages, same document)
jui 19 18:33:04.15: : <-
jui 19 18:33:04.17: : ->
jui 19 18:33:04.17: : <- HDLC<3:FF C8 F2>
jui 19 18:33:04.17: : <- data
jui 19 18:33:04.17: : <- data
jui 19 18:33:05.14: : ->
jui 19 18:33:05.14: : <-
jui 19 18:33:05.66: : ->
jui 19 18:33:06.56: : -> HDLC<5:FF C8 5F C8 E7>
jui 19 18:33:06.63: : ->
jui 19 18:33:06.63: : SEND recv DCN (disconnect)
jui 19 18:33:06.63: : Remote fax disconnected prematurely
jui 19 18:33:06.63: : <-
jui 19 18:33:06.63: : ->
jui 19 18:33:06.63: : <- HDLC<3:FF C8 DF>
jui 19 18:33:06.63: : <- data
jui 19 18:33:06.63: : <- data
jui 19 18:33:07.60: : ->
jui 19 18:33:07.60: : MODEM input buffering enabled
jui 19 18:33:07.60: : <-
jui 19 18:33:07.72: : ->
jui 19 18:33:07.72: : MODEM set DTR OFF
jui 19 18:33:07.72: : MODEM set baud rate: 0 baud (flow control unchanged)
jui 19 18:33:07.72: : STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
jui 19 18:33:07.72: : SESSION END
If someone can help ….
I've try to change Codec to SLINEAR, i've disable buffer …….
Thanks in advance
Historically users who were also using mISDN have had a lot of trouble. I would start looking at mISDN and then at alternatives.