[hpoj-devel] PSC 2350 & hpoj trouble

[<bil...@gm...>]

Hello,

I have a serious trouble to make running hpoj with my PSC 2350 ...

I'm using a Debian in SID ... with a hand made kernel 2.6.13.1

I have connected the printer in USB ...

less /proc/bus/usb/devices :
T:  Bus=3D01 Lev=3D01 Prnt=3D01 Port=3D00 Cnt=3D01 Dev#=3D  4 Spd=3D12  MxC=
h=3D 0
D:  Ver=3D 2.00 Cls=3D00(>ifc ) Sub=3D00 Prot=3D00 MxPS=3D 8 #Cfgs=3D  1
P:  Vendor=3D03f0 ProdID=3D4911 Rev=3D 1.00
S:  Manufacturer=3DHP
S:  Product=3DPSC 2350 series
S:  SerialNumber=3DHU47TBR17TKJ
C:* #Ifs=3D 4 Cfg#=3D 1 Atr=3Dc0 MxPwr=3D  2mA
I:  If#=3D 0 Alt=3D 0 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dcc Prot=3D00 Driver=
=3D(none)
E:  Ad=3D01(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D81(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D82(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 1 Alt=3D 0 #EPs=3D 3 Cls=3D07(print) Sub=3D01 Prot=3D02 Driver=
=3Dusblp
E:  Ad=3D03(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D83(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D84(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 2 Alt=3D 0 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dff Prot=3Dff Driver=
=3D(none)
E:  Ad=3D05(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D85(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D86(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 2 Alt=3D 1 #EPs=3D 3 Cls=3Dff(vend.) Sub=3Dd4 Prot=3D00 Driver=
=3D(none)
E:  Ad=3D05(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D85(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D86(I) Atr=3D03(Int.) MxPS=3D   8 Ivl=3D10ms
I:  If#=3D 3 Alt=3D 0 #EPs=3D 2 Cls=3D08(stor.) Sub=3D06 Prot=3D50 Driver=
=3Dusb-storage
E:  Ad=3D07(O) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms
E:  Ad=3D87(I) Atr=3D02(Bulk) MxPS=3D  64 Ivl=3D0ms

So it seems that the usblp and usb-storage are here ...

But :
ptal-init setup give me alway this answer ...

Probe for USB-connected devices ([y]/n)?

Probing "/dev/usb/lp0"...
    *** Found "PSC 2350 series" but failed to communicate with it!
    *** Elapsed time for this attempt was 0 second(s).
    *** Check syslog file for ptal-mlcd error messages.
    *** See hpoj documentation for troubleshooting information.

I haven't find any solution in the documentation ...
=46or your information I'm printing perfectly on my printer using CUPS with=
 this=20
configuration :
# Printer configuration file for CUPS v1.1.23
# Written by cupsd on dim 18 d=E9c 2005 03:22:43 CET
<DefaultPrinter HP_PSC2350>
Info Imprimante Jet d'encre couleur
Location Bureau Herv=E9
DeviceURI usb://5740?serial=3DHU47TBR17TKJ
State Idle
Accepting Yes
JobSheets none none
QuotaPeriod 0
PageLimit 0
KLimit 0
</Printer>

So what can I do to make hpoj running ?? I want to use xsane for scanning .=
=2E.=20
and I haven't found any solution ... thanks per advance ...

Regards,
=2D-=20
Herv=E9 Piedvache