Re: [Hamlib-developer] [wsjt-devel] Hamlib new version fails on YAESU FT-100 VFO handling

[Marco C. <PY...@ou...>]

Well,

Since my issue persists and apparently nobody provided answers, I 
abandoned Hamlib NET option and I switched to Rig=YAESU FT-100: this is 
working under every situation!

73 de Marco, PY1ZRJ



Il 13/10/25 09:55, Marco Calistri via wsjt-devel ha scritto:
> *WRONG!
> *
> The issue is till present also in the new Hamlib!
>
> I need to manually switch off  the split operation in my FT-100, then 
> click again on the new band, otherwise VFOB keeps using the previous band!
>
> I use mode Rig in my WSJTX Radio Settings.
>
> Very dumb issue which was not present on the older Hamlib!
>
> Sorry for the wrong announcement!
>
> Regards!
>
> Marco, PY1ZRJ
>
> Il 13/10/25 08:19, Marco Calistri ha scritto:
>> Hello!
>>
>> Updating to
>>
>> *rigctld Hamlib 4.7~git 2025-10-10T14:52:54Z SHA=23710cf2d 64-bit*
>>
>> Has resolved the issue I spoken about in my previous message.
>>
>> So far, so good!
>>
>> Thanks,
>>
>>
>> ---
>> *73 de Marco, PY1ZRJ (former IK5BCU)*
>> **
>>
>>
>>
>> Il 30/09/25 11:57, Marco Calistri ha scritto:
>>> Hello,
>>>
>>> Hope someone of the Hamlib group being sneaking here.
>>>
>>> So far my rigctld command to drive my YAESU FT-100 CAT port has 
>>> worked flawlessly:
>>>
>>> /usr/local/bin/rigctld -m 1021 -r /dev/FT-100_USB1 -t 4532 -s 4800 
>>> *--vfo* &
>>>
>>> This by using older Hamlib version:
>>> rigctld --version: rigctld Hamlib 4.6~git 2023-07-20T21:59:57Z 
>>> SHA=aacf06 64-bit
>>>
>>> Now, using the new Hamlib version:
>>>
>>> rigctld --version: rigctld Hamlib 4.7~git 2025-09-27T16:16:32Z 
>>> SHA=0d122f6b1 64-bit
>>>
>>> One of the VFO stays on previous frequency when I switch band.
>>>
>>> For example: I start working on 10 meters band then VFOA tunes on 
>>> 28.074 and VFOB tunes on the same frequency minus or plus the audio 
>>> shift.
>>>
>>> When I switch band, for example to 17 meters, VFOA sets on 18.100, 
>>> whereas VFOB stays on 28.074!
>>>
>>> This is a really annoying behavior!
>>>
>>> I tried also without adding the *--vfo* parameter at rigctld without 
>>> success and obtaining a worst and slower switching from TX to RX.
>>>
>>> Thanks for any inputs you could provide.
>>>
>>> Marco, PY1ZRJ
>>> ---
>>> *73 de Marco, PY1ZRJ (former IK5BCU)*
>>> **
>>
>>
>
>
> ---
> *73 de Marco, PY1ZRJ (former IK5BCU)*
> **
>
>
> _______________________________________________
> wsjt-devel mailing list
> wsj...@li...
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel


---
*73 de Marco, PY1ZRJ (former IK5BCU)*
**