Re: [Hamlib-developer] HamLib and Codan

[Don P. <ke...@gm...>]

Mr Black,
Still no go.  See attached screenshot.  If you want, you can call me at
918-332-6241 tonight anytime after 4PM CST.
Don KE9XB

On Wed, Feb 12, 2025 at 10:45 PM Black Michael <mdb...@ya...> wrote:

>
> I asked earlier for the WSJT-X_RigControl.log file.
> Please find that email and send it to me.  Looks like is should be working
> OK.
>
>
>
>
>
>
>
> On Wednesday, February 12, 2025 at 06:36:43 PM CST, Don Poquette <
> ke...@gm...> wrote:
>
>
>
>
>
> Here is a picture of  CICS terminal session.
>
> Don
>
> On Wed, Feb 12, 2025, 18:29 Don Poquette <ke...@gm...> wrote:
> > No, because the same port is used by the NSP software for programming of
> the radio.  When I am in CiCS, I can change frequency and mode.
> >
> > On Wed, Feb 12, 2025, 15:09 Black Michael <mdb...@ya...> wrote:
> >> You tried swapping RX/TX lines?
> >> Looks like you saw your own freq cat command and not the response.
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >> On Wednesday, February 12, 2025 at 03:04:31 PM CST, Don Poquette <
> ke...@gm...> wrote:
> >>
> >>
> >>
> >>
> >>
> >> Options for the RS232 are as follows:
> >> GPS (I don't have)
> >> CICS
> >> 3012
> >> 3033/RTU- 292
> >> Pactor I
> >> HAL/Clover
> >> 3212/RM50e
> >> Modem Fast AGC
> >> VP-116
> >>
> >> I know this works with CICS.  Others, I don't know.  Most likely it
> will need some type of hardware and firmware.
> >>
> >> It is looking like either I learn to make my own logging software in
> CICS or just forget the whole idea.
> >>
> >>
> >> On Tue, Feb 11, 2025, 22:16 Black Michael <mdb...@ya...> wrote:
> >>> I have no idea -- what other options do you have?
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>  On Tuesday, February 11, 2025 at 07:13:33 PM CST, Don Poquette <
> ke...@gm...> wrote:
> >>>
> >>>
> >>>
> >>>
> >>>
> >>> Mike, do I use the rs232 in CICS?
> >>> Don
> >>>
> >>> On Tue, Feb 11, 2025, 16:10 Black Michael <mdb...@ya...> wrote:
> >>>> Please use the latest WSJT-X improved
> >>>> https://sourceforge.net/projects/wsjt-x-improved/
> >>>>
> >>>> Then turn on Save/Diagnostic mode and send me
> the Desktop\logs\WSJT-X_RigControl.log
> >>>>
> >>>> It is expecting the login to be "admin" with no password right now.
> >>>>
> >>>> Mike W9MDB
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>  On Tuesday, February 11, 2025 at 01:24:26 PM CST, Don Poquette <
> ke...@gm...> wrote:
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> I tried using the Codan NGT for my 2110.  But nothing happens.
> Running 9600 baud and the radio's rs232 is set to CICS.
> >>>>
> >>>> Don
> >>>>
> >>>> On Tue, Feb 11, 2025, 09:48 gm...@bt... <
> gm...@bt...> wrote:
> >>>>>
> >>>>>
> >>>>>  Hi Don,
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>  Hamlib is a library which is compiled into a lot of ham radio
> software. If the software does use hamlib, then your radios should be
> available in the drop down list as Codan Envoy and Codan NGT. I've checked
> with both WSJT-X and FL-DIGI and these are both in the drop down list.
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>  There is also a command-line interface (rigctl) that you can use.
> You will have to read the manual to find the exact commands to use.
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>  I hope that helps. 73
> >>>>>
> >>>>>  Phil GM3ZZA
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> ________________________________
> >>>>> From: Don Poquette <ke...@gm...>
> >>>>> Sent: 11 February 2025 12:50 PM
> >>>>> To: ham...@li... <
> ham...@li...>
> >>>>> Subject: [Hamlib-developer] HamLib and Codan
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> I use ham software to control my radios like other folks.  I noticed
> HAMLIB has the ability to control Codan radios (versions 4.5 and 4.6).  How
> do I use HAMLIB to connect to a Codan NGT radio?  I tried using the normal
> way via the windows ham software and it doesn't work.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Don Poquette
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>
> >>>> _______________________________________________
> >>>> Hamlib-developer mailing list
> >>>> Ham...@li...
> >>>> https://lists.sourceforge.net/lists/listinfo/hamlib-developer
> >>>>
> >>>>
> >>>
> >>>
> >>>
> >>
> >>
> >
>
>