Re: [Hamlib-developer] HamLib and Codan

[Don P. <ke...@gm...>]

Here is a picture of  CICS terminal session.

Don

On Wed, Feb 12, 2025, 18:29 Don Poquette <ke...@gm...> wrote:

> No, because the same port is used by the NSP software for programming of
> the radio.  When I am in CiCS, I can change frequency and mode.
>
> On Wed, Feb 12, 2025, 15:09 Black Michael <mdb...@ya...> wrote:
>
>> You tried swapping RX/TX lines?
>> Looks like you saw your own freq cat command and not the response.
>>
>>
>>
>>
>>
>>
>>
>>
>> On Wednesday, February 12, 2025 at 03:04:31 PM CST, Don Poquette <
>> ke...@gm...> wrote:
>>
>>
>>
>>
>>
>> Options for the RS232 are as follows:
>> GPS (I don't have)
>> CICS
>> 3012
>> 3033/RTU- 292
>> Pactor I
>> HAL/Clover
>> 3212/RM50e
>> Modem Fast AGC
>> VP-116
>>
>> I know this works with CICS.  Others, I don't know.  Most likely it will
>> need some type of hardware and firmware.
>>
>> It is looking like either I learn to make my own logging software in CICS
>> or just forget the whole idea.
>>
>>
>> On Tue, Feb 11, 2025, 22:16 Black Michael <mdb...@ya...> wrote:
>> > I have no idea -- what other options do you have?
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >  On Tuesday, February 11, 2025 at 07:13:33 PM CST, Don Poquette <
>> ke...@gm...> wrote:
>> >
>> >
>> >
>> >
>> >
>> > Mike, do I use the rs232 in CICS?
>> > Don
>> >
>> > On Tue, Feb 11, 2025, 16:10 Black Michael <mdb...@ya...> wrote:
>> >> Please use the latest WSJT-X improved
>> >> https://sourceforge.net/projects/wsjt-x-improved/
>> >>
>> >> Then turn on Save/Diagnostic mode and send me
>> the Desktop\logs\WSJT-X_RigControl.log
>> >>
>> >> It is expecting the login to be "admin" with no password right now.
>> >>
>> >> Mike W9MDB
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>  On Tuesday, February 11, 2025 at 01:24:26 PM CST, Don Poquette <
>> ke...@gm...> wrote:
>> >>
>> >>
>> >>
>> >>
>> >>
>> >> I tried using the Codan NGT for my 2110.  But nothing happens.
>> Running 9600 baud and the radio's rs232 is set to CICS.
>> >>
>> >> Don
>> >>
>> >> On Tue, Feb 11, 2025, 09:48 gm...@bt... <
>> gm...@bt...> wrote:
>> >>>
>> >>>
>> >>>  Hi Don,
>> >>>
>> >>>
>> >>>
>> >>>
>> >>>  Hamlib is a library which is compiled into a lot of ham radio
>> software. If the software does use hamlib, then your radios should be
>> available in the drop down list as Codan Envoy and Codan NGT. I've checked
>> with both WSJT-X and FL-DIGI and these are both in the drop down list.
>> >>>
>> >>>
>> >>>
>> >>>
>> >>>  There is also a command-line interface (rigctl) that you can use.
>> You will have to read the manual to find the exact commands to use.
>> >>>
>> >>>
>> >>>
>> >>>
>> >>>  I hope that helps. 73
>> >>>
>> >>>  Phil GM3ZZA
>> >>>
>> >>>
>> >>>
>> >>>
>> >>>
>> >>> ________________________________
>> >>> From: Don Poquette <ke...@gm...>
>> >>> Sent: 11 February 2025 12:50 PM
>> >>> To: ham...@li... <
>> ham...@li...>
>> >>> Subject: [Hamlib-developer] HamLib and Codan
>> >>>
>> >>>
>> >>>
>> >>>
>> >>> I use ham software to control my radios like other folks.  I noticed
>> HAMLIB has the ability to control Codan radios (versions 4.5 and 4.6).  How
>> do I use HAMLIB to connect to a Codan NGT radio?  I tried using the normal
>> way via the windows ham software and it doesn't work.
>> >>>
>> >>>
>> >>>
>> >>> Don Poquette
>> >>>
>> >>>
>> >>>
>> >>>
>> >>
>> >> _______________________________________________
>> >> Hamlib-developer mailing list
>> >> Ham...@li...
>> >> https://lists.sourceforge.net/lists/listinfo/hamlib-developer
>> >>
>> >>
>> >
>> >
>> >
>>
>>