Re: [Hamlib-developer] HamLib and Codan

[Black M. <mdb...@ya...>]

I asked earlier for the WSJT-X_RigControl.log file.
Please find that email and send it to me.  Looks like is should be working OK.







On Wednesday, February 12, 2025 at 06:36:43 PM CST, Don Poquette <ke...@gm...> wrote: 





Here is a picture of  CICS terminal session.

Don

On Wed, Feb 12, 2025, 18:29 Don Poquette <ke...@gm...> wrote:
> No, because the same port is used by the NSP software for programming of the radio.  When I am in CiCS, I can change frequency and mode.
> 
> On Wed, Feb 12, 2025, 15:09 Black Michael <mdb...@ya...> wrote:
>> You tried swapping RX/TX lines?
>> Looks like you saw your own freq cat command and not the response.
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>> On Wednesday, February 12, 2025 at 03:04:31 PM CST, Don Poquette <ke...@gm...> wrote: 
>> 
>> 
>> 
>> 
>> 
>> Options for the RS232 are as follows:
>> GPS (I don't have)
>> CICS
>> 3012
>> 3033/RTU- 292
>> Pactor I
>> HAL/Clover
>> 3212/RM50e
>> Modem Fast AGC
>> VP-116
>> 
>> I know this works with CICS.  Others, I don't know.  Most likely it will need some type of hardware and firmware.  
>> 
>> It is looking like either I learn to make my own logging software in CICS or just forget the whole idea.
>> 
>> 
>> On Tue, Feb 11, 2025, 22:16 Black Michael <mdb...@ya...> wrote:
>>> I have no idea -- what other options do you have?
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>>  
>>>  
>>>  On Tuesday, February 11, 2025 at 07:13:33 PM CST, Don Poquette <ke...@gm...> wrote: 
>>> 
>>> 
>>> 
>>> 
>>> 
>>> Mike, do I use the rs232 in CICS?
>>> Don
>>> 
>>> On Tue, Feb 11, 2025, 16:10 Black Michael <mdb...@ya...> wrote:
>>>> Please use the latest WSJT-X improved
>>>> https://sourceforge.net/projects/wsjt-x-improved/
>>>> 
>>>> Then turn on Save/Diagnostic mode and send me the Desktop\logs\WSJT-X_RigControl.log
>>>> 
>>>> It is expecting the login to be "admin" with no password right now.
>>>> 
>>>> Mike W9MDB
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>>  
>>>>  
>>>>  On Tuesday, February 11, 2025 at 01:24:26 PM CST, Don Poquette <ke...@gm...> wrote: 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> I tried using the Codan NGT for my 2110.  But nothing happens.  Running 9600 baud and the radio's rs232 is set to CICS.
>>>> 
>>>> Don
>>>> 
>>>> On Tue, Feb 11, 2025, 09:48 gm...@bt... <gm...@bt...> wrote:
>>>>>  
>>>>>  
>>>>>  Hi Don,
>>>>> 
>>>>>  
>>>>> 
>>>>> 
>>>>>  Hamlib is a library which is compiled into a lot of ham radio software. If the software does use hamlib, then your radios should be available in the drop down list as Codan Envoy and Codan NGT. I've checked with both WSJT-X and FL-DIGI and these are both in the drop down list.
>>>>> 
>>>>>  
>>>>> 
>>>>> 
>>>>>  There is also a command-line interface (rigctl) that you can use. You will have to read the manual to find the exact commands to use.
>>>>> 
>>>>>  
>>>>> 
>>>>> 
>>>>>  I hope that helps. 73
>>>>> 
>>>>>  Phil GM3ZZA
>>>>> 
>>>>> 
>>>>> 
>>>>>  
>>>>> 
>>>>> ________________________________ 
>>>>> From: Don Poquette <ke...@gm...>
>>>>> Sent: 11 February 2025 12:50 PM
>>>>> To: ham...@li... <ham...@li...>
>>>>> Subject: [Hamlib-developer] HamLib and Codan 
>>>>>  
>>>>> 
>>>>> 
>>>>>  
>>>>> I use ham software to control my radios like other folks.  I noticed HAMLIB has the ability to control Codan radios (versions 4.5 and 4.6).  How do I use HAMLIB to connect to a Codan NGT radio?  I tried using the normal way via the windows ham software and it doesn't work. 
>>>>> 
>>>>> 
>>>>> 
>>>>> Don Poquette
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>> 
>>>> _______________________________________________
>>>> Hamlib-developer mailing list
>>>> Ham...@li...
>>>> https://lists.sourceforge.net/lists/listinfo/hamlib-developer
>>>> 
>>>> 
>>> 
>>> 
>>> 
>> 
>> 
>