[Hamlib-developer] rigctl send_cmd

[Jere S. <k4...@gm...>]

I am trying to use the send_cmd to load the memories in my FT-991A, however, when I do "w FA" to read frequency, 0 bytes are sent, the 'f' command works ok, see below:

rigctl -m 135 -r /dev/tty.SLAB_USBtoUART -s 9600 -t';' -vvvvv
rigctl, Hamlib 3.0.1
Report bugs to <ham...@li...>

rig:rig_init called 
yaesu: initrigs3_yaesu called
rig_register (121)
rig_register (127)
rig_register (110)
rig_register (105)
rig_register (106)
rig_register (107)
rig_register (109)
rig_register (120)
rig_register (101)
rig_register (122)
rig_register (123)
rig_register (111)
rig_register (115)
rig_register (113)
rig_register (114)
rig_register (128)
rig_register (131)
rig_register (116)
rig_register (103)
rig_register (124)
rig_register (104)
rig_register (125)
rig_register (129)
rig_register (132)
rig_register (130)
rig_register (117)
rig_register (119)
rig_register (118)
rig_register (126)
rig_register (133)
rig_register (134)
rig_register (135)
ft991_init called, version 0.22.4
newcat_init called
rig:rig_open called 
newcat_open called
newcat_open: write_delay = 0 msec
newcat_open: post_write_delay = 50 msec
newcat_set_trn called
newcat_valid_command called
newcat_valid_command AI
cmd_str = AI0;
cmd_str = AI0;
write_block(): TX 4 bytes
0000    41 49 30 3b                                         AI0;            
cmd_str = ID;
write_block(): TX 3 bytes
0000    49 44 3b                                            ID;             
read_string(): RX 7 characters
0000    49 44 30 36 37 30 3b                                ID0670;         
newcat_set_cmd: read count = 7, ret_data = ID0670;
newcat_get_vfo called
newcat_valid_command called
newcat_valid_command VS
newcat_valid_command: 'FT-991' command 'VS' not supported
Opened rig model 135, 'FT-991'
Backend version: 0.22.4, Status: Beta

Rig command: w
rigctl_parse: input_line: w
Cmd: fa
write_block(): TX 0 bytes
read_string(): Timed out 2.6782 seconds after 0 chars
Reply: 
Rig command:  f
rigctl_parse: input_line: f
newcat_get_freq called
newcat_get_freq: passed vfo = 0x20000000
newcat_valid_command called
newcat_valid_command FA
newcat_set_vfo_from_alias: alias vfo = 0x20000000
newcat_valid_command called
newcat_valid_command FA
cmd_str = FA;
cmd_str = FA;
write_block(): TX 3 bytes
0000    46 41 3b                                            FA;             
read_string(): RX 12 characters
0000    46 41 30 30 37 30 37 34 30 30 30 3b                 FA007074000;    
newcat_get_cmd: read count = 12, ret_data = FA007074000;
newcat_get_freq: freq = 7074000.000000 Hz for vfo 0x01
Frequency: 7074000


Jere Sandidge
k4...@gm...