[Gumstix-users] Need help on ethernet not showing up...

[Mayur S. <ss...@gm...>]

All

I updated my buildroot with the
http://docswiki.gumstix.com/net-wifi-microusd link, to include the patches


Here is my boot log,


Linux version 2.6.21gum (mayur@xlhost.xldomain) (gcc version 4.1.1) #1 Mon
Oct 15 15:34:16 PDT 2007
CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=0000397f
Machine: The Gumstix Platform
Memory policy: ECC disabled, Data cache writeback
Run Mode clock: 208.00MHz (*16)
Turbo Mode clock: 416.00MHz (*2.0, active)
Memory clock: 104.00MHz (/2)
System bus clock: 104.00MHz
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: console=ttyS0,115200n8 root=1f01 rootfstype=jffs2
reboot=cold,hard
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62848KB available (1748K code, 192K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: pxa_timer clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler cfq registered (default)
Console: switching to colour frame buffer device 80x24
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
Probing Gumstix Flash ROM at physical address 0x00000000 (16-bit bankwidth)
Gumstix Flash ROM: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Using static partitions on Gumstix Flash ROM
Creating 3 MTD partitions on "Gumstix Flash ROM":
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00f00000 : "RootFS"
0x00f00000-0x01000000 : "Kernel"
TCP cubic registered
XScale iWMMXt coprocessor detected.
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 132K
NET: Registered protocol family 1
CPLD responded with: ff
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pxa27x-ohci pxa27x-ohci: PXA27x OHCI
pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1
pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing random number generator... done.
Starting Bluetooth subsystem: hcid.
Starting network...
udhcpc (v0.9.9-pre) started
Dec 31 16:00:15 udhcpc[294]: udhcpc (v0.9.9-pre) started
m
Dec 31 16:00:15 udhcpc[294]: [truncated] m
cfio: module license 'unspecified' taints kernel.
Before register driver
After register driver
Error for wireless request "Set ESSID" (8B1A) :
    SET failed on device mwlan0 ; No such device.
Starting Rendezvous:
NET: Registered protocol family 10
Mobile IPv6
Starting dropbear sshd: OK
Starting httpd...
Starting system message bus: done




As you can see I should get some message that says eth0 is up or assign the
IP address to eth0

Looks like there is some problem with our setting, can someone please look
into this?

Any help will be appreicated.


Tx
Mayur