I try that but it still doesn't make it faster. I think it wouldn't matter since it is after the kernel load anyways and the pause i am seeing is during kernel load not init.

On Fri, Oct 29, 2010 at 3:48 PM, Chris Whittenburg <whittenburg@gmail.com> wrote:
yes, sorry, I meant checkroot. †When I was timing things, I remember
spending a good amount of time at the "remouting root file system"
line. †I think if the fs is clean, then checkroot isn't needed since
the rootfs is mounted rw to begin with anyway.


On Fri, Oct 29, 2010 at 2:35 PM, Dat Tran <dtran11@gmail.com> wrote:
> I couldn't find†checkdisk.sh but I did find S10checkroot hich points to
> /etc//init.d/checkroot. Are they the same? Anyways I did try to remove
> S10checkroot but no luck.
> Thanks.
>
> On Fri, Oct 29, 2010 at 2:01 PM, Chris Whittenburg <whittenburg@gmail.com>
> wrote:
>>
>> I disabled checkdisk.sh, udev, and network configuration, and have it
>> booting in 13.3 seconds.
>>
>> Could it be checkdisk which is causing your delay?
>>
>> -chris
>>
>>
>> On Fri, Oct 29, 2010 at 1:23 PM, dtran11 <dtran11@gmail.com> wrote:
>> >
>> > Scott, I haven't found a way to remove that pause of 4-5 seconds
>> > inbetween
>> > "mmcblk0: p1 p2" and "kjournald starting" yet but I am going to get a
>> > SDHC
>> > card to match your setup. I am currently using a regular SD card. Here
>> > is my
>> > whole boot log:
>> >
>> >
>> > Texas Instruments X-Loader 1.4.4ss (Oct 29 2010 - 12:34:19)
>> > OMAP3503-GP ES3.1
>> > Board revision: 0
>> > Reading boot sector
>> > Loading u-boot.bin from mmc
>> >
>> >
>> > U-Boot 2010.09 (Oct 28 2010 - 08:40:49)
>> >
>> > OMAP3503-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
>> > Gumstix Overo board + LPDDR/NAND
>> > I2C: † ready
>> > DRAM: †256 MiB
>> > NAND: †256 MiB
>> > In: † †serial
>> > Out: † serial
>> > Err: † serial
>> > Board revision: 0
>> > Direct connection on mmc2
>> > No EEPROM on expansion board
>> > Die ID #4d4c00040000000004035c140d009004
>> > Net: † No ethernet found.
>> > Hit any key to stop autoboot: †0
>> > I2C read: I/O error
>> > I2C read: I/O error
>> > mmc1 is available
>> > reading boot.scr
>> >
>> > ** Unable to read "boot.scr" from mmc 0:1 **
>> > reading uImage
>> >
>> > 2333324 bytes read
>> > Booting from mmc ...
>> > ## Booting kernel from Legacy Image at 82000000 ...
>> > † Image Name: † Angstrom/2.6.34/overo
>> > † Image Type: † ARM Linux Kernel Image (uncompressed)
>> > † Data Size: † †2333260 Bytes = 2.2 MiB
>> > † Load Address: 80008000
>> > † Entry Point: †80008000
>> > † Verifying Checksum ... OK
>> > † Loading Kernel Image ... OK
>> > OK
>> >
>> > Starting kernel ...
>> >
>> > Uncompressing Linux... done, booting the kernel.
>> > [ † †0.000000] Linux version 2.6.34 (dtran@dtran-ubuntu) (gcc version
>> > 4.3.3
>> > (GCC) ) #1 Fri Oct 29 09:54:50 CDT 2010
>> > [ † †0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7),
>> > cr=10c53c7f
>> > [ † †0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing
>> > instruction cache
>> > [ † †0.000000] Machine: Gumstix Overo
>> > [ † †0.000000] Memory policy: ECC disabled, Data cache writeback
>> > [ † †0.000000] OMAP3525 ES3.1 (l2cache iva neon isp )
>> > [ † †0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size:
>> > 0x100000
>> > [ † †0.000000] Built 1 zonelists in Zone order, mobility grouping on.
>> > †Total
>> > pages: 65024
>> > [ † †0.000000] Kernel command line: console=ttyS2,115200n8 mpurate=500
>> > vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y
>> > omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
>> > [ † †0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
>> > [ † †0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
>> > bytes)
>> > [ † †0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536
>> > bytes)
>> > [ † †0.000000] Memory: 128MB 128MB = 256MB total
>> > [ † †0.000000] Memory: 255072k/255072k available, 7072k reserved, 0K
>> > highmem
>> > [ † †0.000000] Virtual kernel memory layout:
>> > [ † †0.000000] † † vector †: 0xffff0000 - 0xffff1000 † ( † 4 kB)
>> > [ † †0.000000] † † fixmap †: 0xfff00000 - 0xfffe0000 † ( 896 kB)
>> > [ † †0.000000] † † DMA † † : 0xffc00000 - 0xffe00000 † ( † 2 MB)
>> > [ † †0.000000] † † vmalloc : 0xd0800000 - 0xf8000000 † ( 632 MB)
>> > [ † †0.000000] † † lowmem †: 0xc0000000 - 0xd0000000 † ( 256 MB)
>> > [ † †0.000000] † † modules : 0xbf000000 - 0xc0000000 † ( †16 MB)
>> > [ † †0.000000] † † † .init : 0xc0008000 - 0xc002d000 † ( 148 kB)
>> > [ † †0.000000] † † † .text : 0xc002d000 - 0xc0438000 † (4140 kB)
>> > [ † †0.000000] † † † .data : 0xc0456000 - 0xc048a680 † ( 210 kB)
>> > [ † †0.000000] Hierarchical RCU implementation.
>> > [ † †0.000000] NR_IRQS:402
>> > [ † †0.000000] Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz
>> > [ † †0.000000] Reprogramming SDRC clock to 224791666 Hz
>> > [ † †0.000000] dpll3_m2_clk rate change failed: -22
>> > [ † †0.000000] GPMC revision 5.0
>> > [ † †0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
>> > interrupts
>> > [ † †0.000000] Total of 96 interrupts on 1 active controller
>> > [ † †0.000000] OMAP GPIO hardware version 2.5
>> > [ † †0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
>> > [ † †0.000000] Console: colour dummy device 80x30
>> > [ † †0.000000] Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
>> > [ † †0.000000] Mount-cache hash table entries: 512
>> > [ † †0.000000] CPU: Testing write buffer coherency: ok
>> > [ † †0.000000] devtmpfs: initialized
>> > [ † †0.000000] regulator: core version 0.5
>> > [ † †0.000000] NET: Registered protocol family 16
>> > [ † †0.000000] Found NAND on CS0
>> > [ † †0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
>> > counters available
>> > [ † †0.000000] Switched to new clocking rate (Crystal/Core/MPU):
>> > 26.0/500/224 MHz
>> > [ † †0.000152] OMAP DMA hardware revision 4.0
>> > [ † †0.005218] bio: create slab <bio-0> at 0
>> > [ † †0.006530] SCSI subsystem initialized
>> > [ † †0.006988] usbcore: registered new interface driver usbfs
>> > [ † †0.007171] usbcore: registered new interface driver hub
>> > [ † †0.007385] usbcore: registered new device driver usb
>> > [ † †0.007904] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
>> > [ † †0.010711] twl4030: PIH (irq 7) chaining IRQs 368..375
>> > [ † †0.010772] twl4030: power (irq 373) chaining IRQs 376..383
>> > [ † †0.011230] twl4030: gpio (irq 368) chaining IRQs 384..401
>> > [ † †0.012207] regulator: VUSB1V5: 1500 mV normal standby
>> > [ † †0.012634] regulator: VUSB1V8: 1800 mV normal standby
>> > [ † †0.013000] regulator: VUSB3V1: 3100 mV normal standby
>> > [ † †0.014648] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
>> > [ † †0.015167] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal
>> > standby
>> > [ † †0.015594] regulator: VDAC: 1800 mV normal standby
>> > [ † †0.015960] regulator: VDVI: 1800 mV normal standby
>> > [ † †0.016235] i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
>> > [ † †0.017486] Switching to clocksource 32k_counter
>> > [ † †0.018890] musb_hdrc: version 6.0, musb-dma, peripheral, debug=0
>> > [ † †0.022094] musb_hdrc musb_hdrc: USB Peripheral mode controller at
>> > fa0ab000 using DMA, IRQ 92
>> > [ † †0.022613] NET: Registered protocol family 2
>> > [ † †0.022857] IP route cache hash table entries: 2048 (order: 1, 8192
>> > bytes)
>> > [ † †0.023773] TCP established hash table entries: 8192 (order: 4, 65536
>> > bytes)
>> > [ † †0.024017] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
>> > [ † †0.024139] TCP: Hash tables configured (established 8192 bind 8192)
>> > [ † †0.024169] TCP reno registered
>> > [ † †0.024200] UDP hash table entries: 256 (order: 0, 4096 bytes)
>> > [ † †0.024230] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>> > [ † †0.024475] NET: Registered protocol family 1
>> > [ † †0.024932] RPC: Registered udp transport module.
>> > [ † †0.024963] RPC: Registered tcp transport module.
>> > [ † †0.024963] RPC: Registered tcp NFSv4.1 backchannel transport module.
>> > [ † †0.027282] VFS: Disk quotas dquot_6.5.2
>> > [ † †0.027374] Dquot-cache hash table entries: 1024 (order 0, 4096
>> > bytes)
>> > [ † †0.028656] JFFS2 version 2.2. (NAND) (SUMMARY) †¬© 2001-2006 Red
>> > Hat,
>> > Inc.
>> > [ † †0.029449] msgmni has been set to 498
>> > [ † †0.034271] alg: No test for stdrng (krng)
>> > [ † †0.034637] Block layer SCSI generic (bsg) driver version 0.4 loaded
>> > (major 253)
>> > [ † †0.034667] io scheduler noop registered
>> > [ † †0.034667] io scheduler deadline registered
>> > [ † †0.034820] io scheduler cfq registered (default)
>> > [ † †0.045867] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
>> > [ † †0.067382] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a
>> > ST16654
>> > [ † †0.088043] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a
>> > ST16654
>> > [ † †0.108612] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a
>> > ST16654
>> > [ † †0.615295] console [ttyS2] enabled
>> > [ † †0.626892] brd: module loaded
>> > [ † †0.634155] loop: module loaded
>> > [ † †0.640136] omap2-nand driver initializing
>> > [ † †0.644653] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron
>> > NAND 256MiB 1,8V 16-bit)
>> > [ † †0.653808] cmdlinepart partition parsing not available
>> > [ † †0.659149] Creating 5 MTD partitions on "omap2-nand.0":
>> > [ † †0.664489] 0x000000000000-0x000000080000 : "xloader"
>> > [ † †0.671051] 0x000000080000-0x000000240000 : "uboot"
>> > [ † †0.677551] 0x000000240000-0x000000280000 : "uboot environment"
>> > [ † †0.684478] 0x000000280000-0x000000680000 : "linux"
>> > [ † †0.691864] 0x000000680000-0x000010000000 : "rootfs"
>> > [ † †0.801788] smsc911x: Driver version 2008-10-21.
>> > [ † †0.806518] smsc911x: Driver version 2008-10-21.
>> > [ † †0.811431] usbcore: registered new interface driver asix
>> > [ † †0.817016] usbcore: registered new interface driver cdc_ether
>> > [ † †0.823303] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
>> > Driver
>> > [ † †0.830383] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
>> > [ † †0.836486] ehci-omap ehci-omap.0: new USB bus registered, assigned
>> > bus
>> > number 1
>> > [ † †0.844207] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
>> > [ † †0.861419] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
>> > [ † †0.867431] usb usb1: New USB device found, idVendor=1d6b,
>> > idProduct=0002
>> > [ † †0.874328] usb usb1: New USB device strings: Mfr=3, Product=2,
>> > SerialNumber=1
>> > [ † †0.881622] usb usb1: Product: OMAP-EHCI Host Controller
>> > [ † †0.886993] usb usb1: Manufacturer: Linux 2.6.34 ehci_hcd
>> > [ † †0.892425] usb usb1: SerialNumber: ehci-omap.0
>> > [ † †0.897827] hub 1-0:1.0: USB hub found
>> > [ † †0.901672] hub 1-0:1.0: 3 ports detected
>> > [ † †0.906799] mice: PS/2 mouse device common for all mice
>> > [ † †0.912841] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
>> > [ † †0.919189] twl_rtc twl_rtc: Power up reset detected.
>> > [ † †0.925476] i2c /dev entries driver
>> > [ † †0.930175] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
>> > [ † †0.936401] twl4030_wdt twl4030_wdt: Failed to register misc device
>> > [ † †0.942779] twl4030_wdt: probe of twl4030_wdt failed with error -16
>> > [ † †0.951995] oprofile: using arm/armv7
>> > [ † †0.956024] TCP cubic registered
>> > [ † †0.959289] NET: Registered protocol family 17
>> > [ † †0.963867] NET: Registered protocol family 15
>> > [ † †0.968414] ThumbEE CPU extension supported.
>> > [ † †0.972747] Power Management for TI OMAP3.
>> > [ † †0.983703] VFP support v0.3: implementor 41 architecture 3 part 30
>> > variant c rev 1
>> > [ † †0.994079] regulator_init_complete: incomplete constraints, leaving
>> > VDVI
>> > on
>> > [ † †1.001373] regulator_init_complete: incomplete constraints, leaving
>> > VDAC
>> > on
>> > [ † †1.010742] twl_rtc twl_rtc: setting system clock to 2000-01-01
>> > 00:00:10
>> > UTC (946684810)
>> > [ † †1.033630] Waiting for root device /dev/mmcblk0p2...
>> > [ † †1.424102] mmc0: host does not support reading read-only switch.
>> > assuming write-enable.
>> > [ † †1.432281] mmc0: new SD card at address aaaa
>> > [ † †1.437255] mmcblk0: mmc0:aaaa SU02G 1.84 GiB
>> > [ † †1.442169] †mmcblk0: p1 p2
>> > [ † †5.114044] kjournald starting. †Commit interval 5 seconds
>> > [ † †5.625854] EXT3-fs (mmcblk0p2): using internal journal
>> > [ † †5.631164] EXT3-fs (mmcblk0p2): recovery complete
>> > [ † †5.638244] EXT3-fs (mmcblk0p2): mounted filesystem with writeback
>> > data
>> > mode
>> > [ † †5.645477] VFS: Mounted root (ext3 filesystem) on device 179:2.
>> > [ † †5.654083] devtmpfs: mounted
>> > [ † †5.657135] Freeing init memory: 148K
>> > INIT: version 2.86 booting
>> > Please wait: booting...
>> > Remounting root file system...
>> > root: mount: mount point /dev/pts does not exist
>> > root: mount: mount point /dev/shm does not exist
>> > Configuring network interfaces... done.
>> > Setting up IP spoofing protection: rp_filter.
>> > Fri Oct 29 10:02:00 UTC 2010
>> > INIT: Entering runlevel: 5
>> > Starting OpenBSD Secure Shell server: sshd
>> > done.
>> > Starting syslogd/klogd: done
>> >
>> > .-------.
>> > | † † † | † † † † † † † † †.-.
>> > | † | † |-----.-----.-----.| | † .----..-----.-----.
>> > | † † † | † † | __ †| †---'| '--.| †.-'| † † | † † |
>> > | † | † | †| †| † † |--- †|| †--'| †| †| †' †| | | |
>> > '---'---'--'--'--. †|-----''----''--' †'-----'-'-'-'
>> > † † † † † † † †-' †|
>> > † † † † † † † †'---'
>> >
>> > The Angstrom Distribution overo ttyS2
>> >
>> > Angstrom 2010.7-test-20100927 overo ttyS2
>> >
>> > overo login:
>> > --
>> > View this message in context:
>> > http://old.nabble.com/Tiniest-image-for-serial%2C-ethernet-and-SPI-tp30052469p30088119.html
>> > Sent from the Gumstix mailing list archive at Nabble.com.
>> >
>> >
>> >
>> > ------------------------------------------------------------------------------
>> > Nokia and AT&T present the 2010 Calling All Innovators-North America
>> > contest
>> > Create new apps & games for the Nokia N8 for consumers in †U.S. and
>> > Canada
>> > $10 million total in prizes - $4M cash, 500 devices, nearly $6M in
>> > marketing
>> > Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
>> > http://p.sf.net/sfu/nokia-dev2dev
>> > _______________________________________________
>> > gumstix-users mailing list
>> > gumstix-users@lists.sourceforge.net
>> > https://lists.sourceforge.net/lists/listinfo/gumstix-users
>> >
>>
>>
>> ------------------------------------------------------------------------------
>> Nokia and AT&T present the 2010 Calling All Innovators-North America
>> contest
>> Create new apps & games for the Nokia N8 for consumers in †U.S. and Canada
>> $10 million total in prizes - $4M cash, 500 devices, nearly $6M in
>> marketing
>> Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
>> http://p.sf.net/sfu/nokia-dev2dev
>> _______________________________________________
>> gumstix-users mailing list
>> gumstix-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/gumstix-users
>
>