I'll give that a shot. Thanks.

On Tue, Dec 7, 2010 at 3:44 AM, Grahame Jordan <gbj@theforce.com.au> wrote:
Try turning off portmap/

Starting portmap daemon: portmap.
portmap: fork: No such deviceTurning echo off on /dev/ttyS1
/etc/rcS.d/S97blueprobe: line



On 12/07/2010 02:23 PM, Peter Buelow wrote:
> I had a working Overo Fire, but recently rebuilt the omap3-console-image
> after adding QT to it. However, it now consistently locks up loading the
> bluetooth stack during init. Does this mean the board has given up the
> ghost? Here's the console output. The last line is where it's stuck. At
> that point, the board is completely dead. Is it possible there are still
> issues with 2.6.35? I'm going to build with .34 and .31 in the next
> couple of days to try it, but my big concern here is that the board is
> no longer functioning.
>
> Texas Instruments X-Loader 1.4.2 (Jan 13 2010 - 06:59:23)
> Reading boot sector
> Error: reading boot sector
> Loading u-boot.bin from nand
>
>
> U-Boot 2009.11 (Jan 13 2010 - 07:00:40)
>
> OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
> Gumstix Overo board + LPDDR/NAND
> I2C:   ready
> DRAM:  256 MB
> NAND:  256 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Die ID #0e9e00040000000004036abc0900d017
> Net:   smc911x-0
> Hit any key to stop autoboot:  0
> mmc1 is available
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 2835196 bytes read
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 82000000 ...
>      Image Name:   Angstrom/2.6.35/overo
>      Image Type:   ARM Linux Kernel Image (uncompressed)
>      Data Size:    2835132 Bytes =  2.7 MB
>      Load Address: 80008000
>      Entry Point:  80008000
>      Verifying Checksum ... OK
>      Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
> Linux version 2.6.35 (pete@desktop) (gcc version 4.5.2 20101105
> (prerelease) (GCC) ) #1 Sat Dec 4 18:58:26 CST 2010
> CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
> Machine: Gumstix Overo
> Memory policy: ECC disabled, Data cache writeback
> OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
> SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
> Reserving 12582912 bytes SDRAM for VRAM
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
> Kernel command line: console=ttyS2,115200n8 vram=12M
> omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=lcd43
> root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
> PID hash table entries: 1024 (order: 0, 4096 bytes)
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 128MB = 256MB total
> Memory: 241784k/241784k available, 20360k reserved, 0K highmem
> Virtual kernel memory layout:
>       vector  : 0xffff0000 - 0xffff1000   (   4 kB)
>       fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
>       DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
>       vmalloc : 0xd0800000 - 0xf8000000   ( 632 MB)
>       lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
>       modules : 0xbf000000 - 0xc0000000   (  16 MB)
>         .init : 0xc0008000 - 0xc002d000   ( 148 kB)
>         .text : 0xc002d000 - 0xc0520000   (5068 kB)
>         .data : 0xc0542000 - 0xc0581200   ( 253 kB)
> Hierarchical RCU implementation.
>           RCU-based detection of stalled CPUs is disabled.
>           Verbose stalled-CPUs detection is disabled.
> NR_IRQS:402
> Clocking rate (Crystal/Core/MPU): 26.0/331/500 MHz
> omap_hwmod: l3_hwmod: cannot be enabled (3)
> omap_hwmod: l4_core_hwmod: cannot be enabled (3)
> omap_hwmod: l4_per_hwmod: cannot be enabled (3)
> omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
> Reprogramming SDRC clock to 331882352 Hz
> GPMC revision 5.0
> IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
> Total of 96 interrupts on 1 active controller
> OMAP GPIO hardware version 2.5
> OMAP clockevent source: GPTIMER1 at 32768 Hz
> Console: colour dummy device 80x30
> Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
> pid_max: default: 32768 minimum: 301
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> devtmpfs: initialized
> regulator: core version 0.5
> NET: Registered protocol family 16
> Found NAND on CS0
> OMAP DMA hardware revision 4.0
> bio: create slab<bio-0>  at 0
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
> twl4030: PIH (irq 7) chaining IRQs 368..375
> twl4030: power (irq 373) chaining IRQs 376..383
> twl4030: gpio (irq 368) chaining IRQs 384..401
> regulator: VUSB1V5: 1500 mV normal standby
> regulator: VUSB1V8: 1800 mV normal standby
> regulator: VUSB3V1: 3100 mV normal standby
> twl4030_usb twl4030_usb: Initialized TWL4030 USB module
> regulator: VMMC1: 1850<-->  3150 mV at 3000 mV normal standby
> regulator: VDAC: 1800 mV normal standby
> regulator: VDVI: 1800 mV normal standby
> i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
> Advanced Linux Sound Architecture Driver Version 1.0.23.
> Bluetooth: Core ver 2.15
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> cfg80211: Calling CRDA to update world regulatory domain
> Switching to clocksource 32k_counter
> musb_hdrc: version 6.0, musb-dma, host, debug=0
> musb_hdrc musb_hdrc: MUSB HDRC host driver
> musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: MUSB HDRC host driver
> usb usb1: Manufacturer: Linux 2.6.35 musb-hcd
> usb usb1: SerialNumber: musb_hdrc
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> musb_hdrc musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
> NET: Registered protocol family 2
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> UDP hash table entries: 256 (order: 0, 4096 bytes)
> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> NET: Registered protocol family 1
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> RPC: Registered tcp NFSv4.1 backchannel transport module.
> VFS: Disk quotas dquot_6.5.2
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
> msgmni has been set to 472
> alg: No test for stdrng (krng)
> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> OMAP DSS rev 2.0
> OMAP DISPC rev 3.0
> OMAP VENC rev 2
> OMAP DSI rev 1.0
> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
> serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
> serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
> console [ttyS2] enabled
> brd: module loaded
> loop: module loaded
> omap2-nand driver initializing
> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
> 1,8V 16-bit)
> cmdlinepart partition parsing not available
> Creating 5 MTD partitions on "omap2-nand.0":
> 0x000000000000-0x000000080000 : "xloader"
> 0x000000080000-0x000000240000 : "uboot"
> 0x000000240000-0x000000280000 : "uboot environment"
> 0x000000280000-0x000000680000 : "linux"
> 0x000000680000-0x000010000000 : "rootfs"
> smsc911x: Driver version 2008-10-21.
> smsc911x-mdio: probed
> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
> net eth0: MAC Address: 00:15:c9:28:ca:25
> smsc911x: Driver version 2008-10-21.
> usbcore: registered new interface driver asix
> usbcore: registered new interface driver cdc_ether
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: OMAP-EHCI Host Controller
> usb usb2: Manufacturer: Linux 2.6.35 ehci_hcd
> usb usb2: SerialNumber: ehci-omap.0
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
> twl_rtc twl_rtc: Power up reset detected.
> twl_rtc twl_rtc: Enabling TWL-RTC.
> i2c /dev entries driver
> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> twl4030_wdt twl4030_wdt: Failed to register misc device
> twl4030_wdt: probe of twl4030_wdt failed with error -16
> Bluetooth: HCI UART driver ver 2.2
> Bluetooth: HCI H4 protocol initialized
> Bluetooth: HCI BCSP protocol initialized
> Bluetooth: HCILL protocol initialized
> usbcore: registered new interface driver usbhid
> usbhid: USB HID core driver
> usbcore: registered new interface driver snd-usb-audio
> No device for DAI omap-mcbsp-dai-0
> No device for DAI omap-mcbsp-dai-1
> No device for DAI omap-mcbsp-dai-2
> No device for DAI omap-mcbsp-dai-3
> No device for DAI omap-mcbsp-dai-4
> overo SoC init
> asoc: twl4030<->  omap-mcbsp-dai-0 mapping ok
> ALSA device list:
>     #0: overo (twl4030)
> oprofile: hardware counters not available
> oprofile: using timer interrupt.
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> Bluetooth: L2CAP ver 2.14
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: SCO (Voice Link) ver 0.6
> Bluetooth: SCO socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM ver 1.11
> Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> Bluetooth: BNEP filters: protocol multicast
> Bluetooth: HIDP (Human Interface Emulation) ver 1.2
> ThumbEE CPU extension supported.
> Power Management for TI OMAP3.
> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
> fbcvt: 1024x768@60: CVT Name - .786M3-R
> Console: switching to colour frame buffer device 60x34
> regulator_init_complete: incomplete constraints, leaving VDAC on
> twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
> Waiting for root device /dev/mmcblk0p2...
> mmc0: host does not support reading read-only switch. assuming write-enable.
> mmc0: new high speed SD card at address 75b0
> mmcblk0: mmc0:75b0 SD02G 1.87 GiB
>    mmcblk0: p1 p2
> mmc1: new SDIO card at address 0001
> EXT3-fs: barriers not enabled
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs (mmcblk0p2): using internal journal
> EXT3-fs (mmcblk0p2): recovery complete
> EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
> VFS: Mounted root (ext3 filesystem) on device 179:2.
> devtmpfs: mounted
> Freeing init memory: 148K
> INIT: version 2.86 booting
> mdev: /sys/class: No such file or directory
> NET: Registered protocol family 10
> ALSA: Restoring mixer settings...
> Cleaning: /etc/network/run/ifstate.
> /usr/sbin/alsactl: load_state:1608: No soundcards found...
> Configuring network interfaces... done.
> Starting portmap daemon: portmap.
> portmap: fork: No such deviceTurning echo off on /dev/ttyS1
> /etc/rcS.d/S97blueprobe: line
>
>
> ------------------------------------------------------------------------------
> What happens now with your Lotus Notes apps - do you make another costly
> upgrade, or settle for being marooned without product support? Time to move
> off Lotus Notes and onto the cloud with Force.com, apps are easier to build,
> use, and manage than apps on traditional platforms. Sign up for the Lotus
> Notes Migration Kit to learn more. http://p.sf.net/sfu/salesforce-d2d
> _______________________________________________
> gumstix-users mailing list
> gumstix-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/gumstix-users
>


------------------------------------------------------------------------------
What happens now with your Lotus Notes apps - do you make another costly
upgrade, or settle for being marooned without product support? Time to move
off Lotus Notes and onto the cloud with Force.com, apps are easier to build,
use, and manage than apps on traditional platforms. Sign up for the Lotus
Notes Migration Kit to learn more. http://p.sf.net/sfu/salesforce-d2d
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users



--
Pete