I couldn't find†checkdisk.sh but I did find S10checkroot hich points to /etc//init.d/checkroot. Are they the same? Anyways I did try to remove S10checkroot but no luck.

Thanks.

On Fri, Oct 29, 2010 at 2:01 PM, Chris Whittenburg <whittenburg@gmail.com> wrote:
I disabled checkdisk.sh, udev, and network configuration, and have it
booting in 13.3 seconds.

Could it be checkdisk which is causing your delay?

-chris


On Fri, Oct 29, 2010 at 1:23 PM, dtran11 <dtran11@gmail.com> wrote:
>
> Scott, I haven't found a way to remove that pause of 4-5 seconds inbetween
> "mmcblk0: p1 p2" and "kjournald starting" yet but I am going to get a SDHC
> card to match your setup. I am currently using a regular SD card. Here is my
> whole boot log:
>
>
> Texas Instruments X-Loader 1.4.4ss (Oct 29 2010 - 12:34:19)
> OMAP3503-GP ES3.1
> Board revision: 0
> Reading boot sector
> Loading u-boot.bin from mmc
>
>
> U-Boot 2010.09 (Oct 28 2010 - 08:40:49)
>
> OMAP3503-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
> Gumstix Overo board + LPDDR/NAND
> I2C: † ready
> DRAM: †256 MiB
> NAND: †256 MiB
> In: † †serial
> Out: † serial
> Err: † serial
> Board revision: 0
> Direct connection on mmc2
> No EEPROM on expansion board
> Die ID #4d4c00040000000004035c140d009004
> Net: † No ethernet found.
> Hit any key to stop autoboot: †0
> I2C read: I/O error
> I2C read: I/O error
> mmc1 is available
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 2333324 bytes read
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 82000000 ...
> † Image Name: † Angstrom/2.6.34/overo
> † Image Type: † ARM Linux Kernel Image (uncompressed)
> † Data Size: † †2333260 Bytes = 2.2 MiB
> † Load Address: 80008000
> † Entry Point: †80008000
> † Verifying Checksum ... OK
> † Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
> [ † †0.000000] Linux version 2.6.34 (dtran@dtran-ubuntu) (gcc version 4.3.3
> (GCC) ) #1 Fri Oct 29 09:54:50 CDT 2010
> [ † †0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7),
> cr=10c53c7f
> [ † †0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing
> instruction cache
> [ † †0.000000] Machine: Gumstix Overo
> [ † †0.000000] Memory policy: ECC disabled, Data cache writeback
> [ † †0.000000] OMAP3525 ES3.1 (l2cache iva neon isp )
> [ † †0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
> [ † †0.000000] Built 1 zonelists in Zone order, mobility grouping on. †Total
> pages: 65024
> [ † †0.000000] Kernel command line: console=ttyS2,115200n8 mpurate=500
> vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y
> omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
> [ † †0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
> [ † †0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
> bytes)
> [ † †0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> [ † †0.000000] Memory: 128MB 128MB = 256MB total
> [ † †0.000000] Memory: 255072k/255072k available, 7072k reserved, 0K highmem
> [ † †0.000000] Virtual kernel memory layout:
> [ † †0.000000] † † vector †: 0xffff0000 - 0xffff1000 † ( † 4 kB)
> [ † †0.000000] † † fixmap †: 0xfff00000 - 0xfffe0000 † ( 896 kB)
> [ † †0.000000] † † DMA † † : 0xffc00000 - 0xffe00000 † ( † 2 MB)
> [ † †0.000000] † † vmalloc : 0xd0800000 - 0xf8000000 † ( 632 MB)
> [ † †0.000000] † † lowmem †: 0xc0000000 - 0xd0000000 † ( 256 MB)
> [ † †0.000000] † † modules : 0xbf000000 - 0xc0000000 † ( †16 MB)
> [ † †0.000000] † † † .init : 0xc0008000 - 0xc002d000 † ( 148 kB)
> [ † †0.000000] † † † .text : 0xc002d000 - 0xc0438000 † (4140 kB)
> [ † †0.000000] † † † .data : 0xc0456000 - 0xc048a680 † ( 210 kB)
> [ † †0.000000] Hierarchical RCU implementation.
> [ † †0.000000] NR_IRQS:402
> [ † †0.000000] Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz
> [ † †0.000000] Reprogramming SDRC clock to 224791666 Hz
> [ † †0.000000] dpll3_m2_clk rate change failed: -22
> [ † †0.000000] GPMC revision 5.0
> [ † †0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
> interrupts
> [ † †0.000000] Total of 96 interrupts on 1 active controller
> [ † †0.000000] OMAP GPIO hardware version 2.5
> [ † †0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
> [ † †0.000000] Console: colour dummy device 80x30
> [ † †0.000000] Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
> [ † †0.000000] Mount-cache hash table entries: 512
> [ † †0.000000] CPU: Testing write buffer coherency: ok
> [ † †0.000000] devtmpfs: initialized
> [ † †0.000000] regulator: core version 0.5
> [ † †0.000000] NET: Registered protocol family 16
> [ † †0.000000] Found NAND on CS0
> [ † †0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
> counters available
> [ † †0.000000] Switched to new clocking rate (Crystal/Core/MPU):
> 26.0/500/224 MHz
> [ † †0.000152] OMAP DMA hardware revision 4.0
> [ † †0.005218] bio: create slab <bio-0> at 0
> [ † †0.006530] SCSI subsystem initialized
> [ † †0.006988] usbcore: registered new interface driver usbfs
> [ † †0.007171] usbcore: registered new interface driver hub
> [ † †0.007385] usbcore: registered new device driver usb
> [ † †0.007904] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
> [ † †0.010711] twl4030: PIH (irq 7) chaining IRQs 368..375
> [ † †0.010772] twl4030: power (irq 373) chaining IRQs 376..383
> [ † †0.011230] twl4030: gpio (irq 368) chaining IRQs 384..401
> [ † †0.012207] regulator: VUSB1V5: 1500 mV normal standby
> [ † †0.012634] regulator: VUSB1V8: 1800 mV normal standby
> [ † †0.013000] regulator: VUSB3V1: 3100 mV normal standby
> [ † †0.014648] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
> [ † †0.015167] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
> [ † †0.015594] regulator: VDAC: 1800 mV normal standby
> [ † †0.015960] regulator: VDVI: 1800 mV normal standby
> [ † †0.016235] i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
> [ † †0.017486] Switching to clocksource 32k_counter
> [ † †0.018890] musb_hdrc: version 6.0, musb-dma, peripheral, debug=0
> [ † †0.022094] musb_hdrc musb_hdrc: USB Peripheral mode controller at
> fa0ab000 using DMA, IRQ 92
> [ † †0.022613] NET: Registered protocol family 2
> [ † †0.022857] IP route cache hash table entries: 2048 (order: 1, 8192
> bytes)
> [ † †0.023773] TCP established hash table entries: 8192 (order: 4, 65536
> bytes)
> [ † †0.024017] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> [ † †0.024139] TCP: Hash tables configured (established 8192 bind 8192)
> [ † †0.024169] TCP reno registered
> [ † †0.024200] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ † †0.024230] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ † †0.024475] NET: Registered protocol family 1
> [ † †0.024932] RPC: Registered udp transport module.
> [ † †0.024963] RPC: Registered tcp transport module.
> [ † †0.024963] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ † †0.027282] VFS: Disk quotas dquot_6.5.2
> [ † †0.027374] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ † †0.028656] JFFS2 version 2.2. (NAND) (SUMMARY) †¬© 2001-2006 Red Hat,
> Inc.
> [ † †0.029449] msgmni has been set to 498
> [ † †0.034271] alg: No test for stdrng (krng)
> [ † †0.034637] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 253)
> [ † †0.034667] io scheduler noop registered
> [ † †0.034667] io scheduler deadline registered
> [ † †0.034820] io scheduler cfq registered (default)
> [ † †0.045867] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [ † †0.067382] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a
> ST16654
> [ † †0.088043] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a
> ST16654
> [ † †0.108612] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a
> ST16654
> [ † †0.615295] console [ttyS2] enabled
> [ † †0.626892] brd: module loaded
> [ † †0.634155] loop: module loaded
> [ † †0.640136] omap2-nand driver initializing
> [ † †0.644653] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron
> NAND 256MiB 1,8V 16-bit)
> [ † †0.653808] cmdlinepart partition parsing not available
> [ † †0.659149] Creating 5 MTD partitions on "omap2-nand.0":
> [ † †0.664489] 0x000000000000-0x000000080000 : "xloader"
> [ † †0.671051] 0x000000080000-0x000000240000 : "uboot"
> [ † †0.677551] 0x000000240000-0x000000280000 : "uboot environment"
> [ † †0.684478] 0x000000280000-0x000000680000 : "linux"
> [ † †0.691864] 0x000000680000-0x000010000000 : "rootfs"
> [ † †0.801788] smsc911x: Driver version 2008-10-21.
> [ † †0.806518] smsc911x: Driver version 2008-10-21.
> [ † †0.811431] usbcore: registered new interface driver asix
> [ † †0.817016] usbcore: registered new interface driver cdc_ether
> [ † †0.823303] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ † †0.830383] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ † †0.836486] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
> number 1
> [ † †0.844207] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> [ † †0.861419] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ † †0.867431] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ † †0.874328] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ † †0.881622] usb usb1: Product: OMAP-EHCI Host Controller
> [ † †0.886993] usb usb1: Manufacturer: Linux 2.6.34 ehci_hcd
> [ † †0.892425] usb usb1: SerialNumber: ehci-omap.0
> [ † †0.897827] hub 1-0:1.0: USB hub found
> [ † †0.901672] hub 1-0:1.0: 3 ports detected
> [ † †0.906799] mice: PS/2 mouse device common for all mice
> [ † †0.912841] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
> [ † †0.919189] twl_rtc twl_rtc: Power up reset detected.
> [ † †0.925476] i2c /dev entries driver
> [ † †0.930175] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> [ † †0.936401] twl4030_wdt twl4030_wdt: Failed to register misc device
> [ † †0.942779] twl4030_wdt: probe of twl4030_wdt failed with error -16
> [ † †0.951995] oprofile: using arm/armv7
> [ † †0.956024] TCP cubic registered
> [ † †0.959289] NET: Registered protocol family 17
> [ † †0.963867] NET: Registered protocol family 15
> [ † †0.968414] ThumbEE CPU extension supported.
> [ † †0.972747] Power Management for TI OMAP3.
> [ † †0.983703] VFP support v0.3: implementor 41 architecture 3 part 30
> variant c rev 1
> [ † †0.994079] regulator_init_complete: incomplete constraints, leaving VDVI
> on
> [ † †1.001373] regulator_init_complete: incomplete constraints, leaving VDAC
> on
> [ † †1.010742] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:10
> UTC (946684810)
> [ † †1.033630] Waiting for root device /dev/mmcblk0p2...
> [ † †1.424102] mmc0: host does not support reading read-only switch.
> assuming write-enable.
> [ † †1.432281] mmc0: new SD card at address aaaa
> [ † †1.437255] mmcblk0: mmc0:aaaa SU02G 1.84 GiB
> [ † †1.442169] †mmcblk0: p1 p2
> [ † †5.114044] kjournald starting. †Commit interval 5 seconds
> [ † †5.625854] EXT3-fs (mmcblk0p2): using internal journal
> [ † †5.631164] EXT3-fs (mmcblk0p2): recovery complete
> [ † †5.638244] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data
> mode
> [ † †5.645477] VFS: Mounted root (ext3 filesystem) on device 179:2.
> [ † †5.654083] devtmpfs: mounted
> [ † †5.657135] Freeing init memory: 148K
> INIT: version 2.86 booting
> Please wait: booting...
> Remounting root file system...
> root: mount: mount point /dev/pts does not exist
> root: mount: mount point /dev/shm does not exist
> Configuring network interfaces... done.
> Setting up IP spoofing protection: rp_filter.
> Fri Oct 29 10:02:00 UTC 2010
> INIT: Entering runlevel: 5
> Starting OpenBSD Secure Shell server: sshd
> done.
> Starting syslogd/klogd: done
>
> .-------.
> | † † † | † † † † † † † † †.-.
> | † | † |-----.-----.-----.| | † .----..-----.-----.
> | † † † | † † | __ †| †---'| '--.| †.-'| † † | † † |
> | † | † | †| †| † † |--- †|| †--'| †| †| †' †| | | |
> '---'---'--'--'--. †|-----''----''--' †'-----'-'-'-'
> † † † † † † † †-' †|
> † † † † † † † †'---'
>
> The Angstrom Distribution overo ttyS2
>
> Angstrom 2010.7-test-20100927 overo ttyS2
>
> overo login:
> --
> View this message in context: http://old.nabble.com/Tiniest-image-for-serial%2C-ethernet-and-SPI-tp30052469p30088119.html
> Sent from the Gumstix mailing list archive at Nabble.com.
>
>
> ------------------------------------------------------------------------------
> Nokia and AT&T present the 2010 Calling All Innovators-North America contest
> Create new apps & games for the Nokia N8 for consumers in †U.S. and Canada
> $10 million total in prizes - $4M cash, 500 devices, nearly $6M in marketing
> Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
> http://p.sf.net/sfu/nokia-dev2dev
> _______________________________________________
> gumstix-users mailing list
> gumstix-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/gumstix-users
>

------------------------------------------------------------------------------
Nokia and AT&T present the 2010 Calling All Innovators-North America contest
Create new apps & games for the Nokia N8 for consumers in †U.S. and Canada
$10 million total in prizes - $4M cash, 500 devices, nearly $6M in marketing
Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
http://p.sf.net/sfu/nokia-dev2dev
_______________________________________________
gumstix-users mailing list
gumstix-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/gumstix-users