Hello,

I am trying to update my overo fire to the newest image and am having some issues.  Here are the steps i have taken:

1) prepare a bootable sd card via instrucitons here: http://gumstix.org/create-a-bootable-microsd-card.html
- I used the latest "stable" image I could find from here: http://cumulus.gumstix.org/images/angstrom/factory/2011-08-30-1058/
- The card boots fine pending some weird libertas wifi issues (which I will address later)
U-Boot 2010.12 (Aug 22 2011 - 09:49:35)
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Angstrom/2.6.39/overo
Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2914708 Bytes = 2.8 MiB
Load Address: 80008000
Entry Point:  80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39 etc......

2) flash new image to nand (using the same u-boot, uImage, and filesys that I used for the card
- used the script from here: http://gumstix.org/how-to/70-writing-images-to-flash.html
- some output I get (note the JFFS2 notice?):
Erasing u-boot partition ...
flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please use it
Erasing 128 Kibyte @ 1a0000 -- 100 % complete 
Erasing u-boot environment partition ...
flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please use it
Erasing 128 Kibyte @ 20000 -- 100 % complete 
Writing u-boot to NAND ...
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
u-boot image has been written to NAND ...
Erasing kernel partition ...
flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please use it
Erasing 128 Kibyte @ 3e0000 -- 100 % complete 
Writing kernel to NAND ...
Writing data to block 0 at offset 0x0
...
Writing data to block 22 at offset 0x2c0000
Kernel image has been written to NAND ...
Erasing and formatting rootfs partition ...
flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please use it
Erasing 128 Kibyte @ 0 --  0 % complete flash_erase:  Cleanmarker written at 0
Erasing 128 Kibyte @ 20000 --  0 % complete flash_erase:  Cleanmarker written at 20000
...
Erasing 128 Kibyte @ 1f960000 -- 99 % complete flash_erase:  Cleanmarker written at 1f960000
Erasing 128 Kibyte @ 1f960000 -- 100 % complete
Mounting rootfs partition ...
JFFS2 notice: (1245) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
The rootfs has been written to the NAND ...
The NAND restoration is complete ...

3) shutdown and restart without sdcard
-output (particularly scary is the Card did not respond to voltage select!  MMC: block number 0x1 exceeds max(0x0) ** Can't read from device 0 ** etc.)

U-Boot 2010.12 (Aug 22 2011 - 09:49:35)

OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
Gumstix Overo board + LPDDR/NAND
I2C:   ready
DRAM:  512 MiB
NAND:  512 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Board revision: 1
Tranceiver detected on mmc2
No EEPROM on expansion board
Die ID #47040004000000000403d0a31900d00f
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
Card did not respond to voltage select!
MMC: block number 0x1 exceeds max(0x0)
** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **
MMC: block number 0x1 exceeds max(0x0)
** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **
Booting from nand ...

NAND read: device 0 offset 0x280000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Angstrom/2.6.39/overo
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2914708 Bytes = 2.8 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39 (neil@cumulus) (gcc version 4.3.3 (GCC) ) #1 Mon Aug 15 19:04:09 PDT 2011
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
Reserving 12582912 bytes SDRAM for VRAM
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz
Reprogramming SDRC clock to 224791666 Hz
dpll3_m2_clk rate change failed: -22
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 126976
Kernel command line: console=ttyO2,115200n8 mpurate=600 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=ubi0:rootfs ubi.mtd=4 rootfstype=ubifs
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 500MB = 500MB total
Memory: 501204k/501204k available, 23084k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xe0800000 - 0xf8000000   ( 376 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0039000   ( 196 kB)
      .text : 0xc0039000 - 0xc0574944   (5359 kB)
      .data : 0xc0576000 - 0xc05b75c0   ( 262 kB)
NR_IRQS:410
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP clockevent source: GPTIMER1 at 32768 Hz
sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
Console: colour dummy device 80x30
Calibrating delay loop... 497.82 BogoMIPS (lpj=1941504)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
omap_hwmod: i2c1: softreset failed (waited 10000 usec)
omap_hwmod: i2c2: softreset failed (waited 10000 usec)
omap_hwmod: i2c3: softreset failed (waited 10000 usec)
omap_hwmod: am35x_otg_hs: cannot be enabled (3)
print_constraints: dummy: 
NET: Registered protocol family 16
GPMC revision 5.0
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
omap_mux_init: Add partition: #1: core, flags: 0
Found NAND on CS0
Registering NAND on CS0
hw-breakpoint: debug architecture 0x4 unsupported.
Switched to new clocking rate (Crystal/Core/MPU): 26.0/224/600 MHz
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
print_constraints: vads7846: 3300 mV 
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
print_constraints: VUSB1V5: 1500 mV normal standby
print_constraints: VUSB1V8: 1800 mV normal standby
print_constraints: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
print_constraints: VDAC: 1800 mV normal standby
print_constraints: VDVI: 1800 mV normal standby
omap_i2c omap_i2c.3: bus 3 rev3.12 at 400 kHz
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource 32k_counter
Switched to NOHz mode on CPU #0
musb-hdrc: version 6.0, musb-dma, host, debug=0
musb-hdrc musb-hdrc: MUSB HDRC host driver
musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.39 musb-hcd
usb usb1: SerialNumber: musb-hdrc
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
musb-hdrc musb-hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Registering unionfs 2.5.9 (for 2.6.39-rc5)
JFFS2 version 2.2. (NAND) (SUMMARY)   2001-2006 Red Hat, Inc.
msgmni has been set to 978
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
console [ttyO2] enabled
brd: module loaded
loop: module loaded
omap2-nand driver initializing
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000020000000 : "rootfs"
UBI: attaching mtd4 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: max. sequence number:       0
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd4
smsc911x: Driver version 2008-10-21.
smsc911x: Driver version 2008-10-21.
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
cdc_ncm: 23-Apr-2011
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.39 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mousedev: PS/2 mouse device common for all mice
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
overo SoC init
asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
ALSA device list:
  #0: overo
oprofile: hardware counters not available
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
sr_init: No PMIC hook to init smartreflex
smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
clock: disabling unused clocks to save power
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 128x48
regulator_init_complete: VDAC: incomplete constraints, leaving on
regulator_init_complete: vads7846: incomplete constraints, leaving on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:13 UTC (946684813)
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00             512 mtdblock0  (driver?)
1f01            1792 mtdblock1  (driver?)
1f02             256 mtdblock2  (driver?)
1f03            4096 mtdblock3  (driver?)
1f04          517632 mtdblock4  (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)


Thanks,
Brett