Recent changes to Tutorial_NewSession

Discussion for Tutorial_NewSession page

Melanie Schranz — Mon, 27 Feb 2017 10:20:51 -0000

Hallo Anita!!
Ja so schließen sich die Kreise :)

Wie geht es dir? Es wäre toll, wenn wir uns mal wieder treffen könnten, wann bist du vl. wieder mal in Kärnten?

LG, Melanie

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 14:25:05 -0000

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 14:11:49 -0000

--- v9
+++ v10
@@ -9,12 +9,12 @@

 

-Now you should have defined your parameters. To run the simulation, click the “Play” button and the simulation shall start.
+Now you should have defined your parameters. To run the simulation, click the “Play” button and the simulation starts.

-
+

 One can use the “Reset” button to clear all ongoing simulations. 
-The bottom half of the screen shows information and the progress bar (again outlined in red). 
+The bottom half of the screen shows information to the simulation (outlined in red) and the progress bar.
 When the simulation is finished, results will be saved in the “FREVO” folder, under “Results”.

-
+

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 14:02:03 -0000

--- v8
+++ v9
@@ -3,11 +3,11 @@
 

 * Select a problem component. Here, “Cellular automaton morphogenesis” (Cam) is selected.
-* Define parameters in the table. Here, the “simulation steps” parameter is selected in yellow. To define a parameter, double click and enter a value.
+* You can adjust parameters in the table. Here, the “simulation steps” parameter is selected. To change a parameter's value, double click and enter a value.
 * When you are finished, click “Confirm” at the bottom of the screen.
-* Repeat this step for the Method, Candidate Representation and Ranking, selecting the required parameters.
+* Repeat this step to select a Method, Representation and Ranking. In each step you can adjust parameters.

-
+

 Now you should have defined your parameters. To run the simulation, click the “Play” button and the simulation shall start.

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 13:57:41 -0000

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 13:53:55 -0000

--- v6
+++ v7
@@ -1,4 +1,4 @@
-To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click on “Select Problem” label, outlined in red. Select “Problem”. The “Select Problem Component” window will then pop up.
+To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click on “Select Problem” label, outlined in red. The “Select Problem Component” window will pop up.

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 13:53:18 -0000

--- v5
+++ v6
@@ -1,4 +1,4 @@
-To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click the “problem” label, outlined in red. Select “Problem”. The “Select Problem Component” window will then pop up.
+To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click on “Select Problem” label, outlined in red. Select “Problem”. The “Select Problem Component” window will then pop up.

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 13:52:14 -0000

Tutorial_NewSession modified by Melanie Schranz

Melanie Schranz — Fri, 24 Feb 2017 13:49:54 -0000

--- v3
+++ v4
@@ -1,6 +1,6 @@
 To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click the “problem” label, outlined in red. Select “Problem”. The “Select Problem Component” window will then pop up.

-
+

 * Select a problem component. Here, “Cellular automaton morphogenesis” (Cam) is selected.
 * Define parameters in the table. Here, the “simulation steps” parameter is selected in yellow. To define a parameter, double click and enter a value.

WikiPage Tutorial_NewSession modified by Anita

Anita — Wed, 08 Aug 2012 08:42:01 -0000

--- v2
+++ v3
@@ -1,3 +1,20 @@
 To set up a new session, start FREVO with the graphical user interface. The first thing that should be selected is the Problem Implementation. To do this, click the “problem” label, outlined in red. Select “Problem”. The “Select Problem Component” window will then pop up.
 
 
+
+* Select a problem component. Here, “Cellular automaton morphogenesis” (Cam) is selected.
+* Define parameters in the table. Here, the “simulation steps” parameter is selected in yellow. To define a parameter, double click and enter a value.
+* When you are finished, click “Confirm” at the bottom of the screen.
+* Repeat this step for the Method, Candidate Representation and Ranking, selecting the required parameters.
+
+
+
+Now you should have defined your parameters. To run the simulation, click the “Play” button and the simulation shall start.
+
+
+
+One can use the “Reset” button to clear all ongoing simulations. 
+The bottom half of the screen shows information and the progress bar (again outlined in red). 
+When the simulation is finished, results will be saved in the “FREVO” folder, under “Results”.
+
+