Page fault while booting livecd since 0.7.3397
This project has moved to github - see https://github.com/freenas
Brought to you by:
cochard,
mattolander
Logged In: YES
user_id=1598685
Originator: NO
Did a normal FreeBSD CD start without problems?
Can you please remove all additional hardware and check if it boots then. After that insert your additional step by step and try to boot. Hopefully we will fid out more then.
Regards
Volker
Logged In: YES
user_id=1441560
Originator: YES
This machine allready runs the latest 0.69 from May 11 without any problems.
AFAIK one major change in 0.7.x is the upgrade to FreeBSD 7.0, correct?
So I will test booting a normal FreeBSD 7 CDRom.
To remove all additional HW from this machine is not so easy, because this chasis
is extremely full and so it is very time expensive, to do a "cleanup".
But lets do it step-by-step.
Rgds
-Wanninger
Logged In: YES
user_id=2060416
Originator: NO
I get a fatal trap 9 error since the 0.7 builds. 0.69 latest build works without problems.
Logged In: YES
user_id=1441560
Originator: YES
ok, I tried to boot FreeBSD 7 livefs iso.
The system boots up until twed0 is loaded.
Then: FATAL TRAP 12 : page fault while in kernel mode.
FreeBSD 6.2 and 6.3 are booting normal, no problem.
I think BSD 7 has a problem booting a system with an
installed HW-Raidcontroller - in my case a 3ware 7500 8ch.
What can we (I) do? This is a problem of BSD 7
-Wanninger
Logged In: YES
user_id=1598685
Originator: NO
Hi,
seems to be a FreeBSD problem. Please fill out a bug report here:
http://www.freebsd.org/send-pr.html
Ahm, please don't mention FreeNAS, don't know if this will slow down the fixing process.
Regards
Volker
Logged In: YES
user_id=1441560
Originator: YES
Hi,
well, i've done so.
Hope that they (BSD) can solve this problem.
There are several people having the same or similar problem with BSD 7.0.
Rgds
-Wanninger
Logged In: YES
user_id=2060416
Originator: NO
I removed all of my PCI cards (PATA controller, SATA controller and NIC) and it didn't make any difference. It's still crashing :(
Logged In: YES
user_id=1441560
Originator: YES
Hi,
I opened a ticket at FreeBSD see:
http://www.freebsd.org/cgi/query-pr.cgi?pr=124124
unfortunately, I'm not able to collect the needed data, because:
Perhaps someone of you is able the collect this data, or can help/assist me how to do it?
...so please help to fixup...
Here is the answer from BSD support in short:
Sadly, given the problems you are seeing, we cannot help you. We need a
backtrace of the actual error/crash so that we can determine what is
happening here. The amount of information you are presenting is a
start, but sadly not enough.
That said, it's probably difficult to get this information straight from
a LiveCD because it might not issue a coredump to the memory which can
be extracted later.
Are you in the position to install 7.0 on the disk and see what is
happening then? (in that case we can probably get a coredump one
way or the other).
Cheers
remko
--
/"\ Best regards, | remko@FreeBSD.org
\ / Remko Lodder | remko@EFnet
X http://www.evilcoder.org/ |
/ \ ASCII Ribbon Campaign | Against HTML Mail and News
Regards
-Wanninger
Logged In: YES
user_id=2071567
Originator: NO
Hi,
I can't solve the problem but I hope I can give some infos. On nearly all of my machines FreeNAS 0.7 hangs with the error described below:
FATAL TRAP 12 : page fault while in kernel mode
cpuid = 0, apicid = 03
fault virtual address = 0x3f80
fault code = supervisor write, page not present
...
trap number 12
panic: page fault
cpuid = 0
Here is the config:
1. Workstation
C2D E6550 on Asus Striker Extreme (nforce 680)
4GB A-Data Ram
2x250GB SATA HD
2xGbit
Laptop (!!)
Pentium 4M 2,13 in Amilo M3438G (915/45 chipset?)
2GB S0-Dimm
2x100GB SATA HD
1xGbit
FreeNAS
1Ghz C7 on SN10000 (VIA CN896 North + VIA VT8251 South Bridge)
2GB DDR2
2x1000GB SATA + 1x500GB SATA
1x100Mbit + 1xGbit
I tried to boot up 0.7.3468.
All 3 systems got onboard raid but disabled on FreeNAS-System and workstation. The CPUs and the chipsets are very different so I think we can exclude some error sources here.
Tell me if I can do some tests somehow.
Greets
Logged In: YES
user_id=1674164
Originator: NO
Hi,
same issues for me
Asus P2 B
There is nothing in this machine except:
CD ROM drive (P-ATA)
2 NICs (PCI)
USB memory stick
http://www.mediafire.com/imageview.php?quickkey=2nmujxwygtj&thumb=4
http://www.mediafire.com/imageview.php?quickkey=xxzt6exlyxz&thumb=4
I have the same with the live cd. 0.7.3514
i get FATAL TRAP 9 : page fault while in kernel mode
running P3 667mhz
512mb ram
Promise UltraATA 133TX2 IDE Controller card.
0.69.4 runs great from cd but doesn't boot from harddisks after install on HD.
nightly build 0.7.3514