Hi
with this hardware: http://www.linitx.com/viewproduct.php?prodid=11714 I only get the ET131x driver to run with 100 MBit in Half Duplex mode.
Details:
hwinfo --netcard (skipped the 8139 cards)
08: PCI 8100.0: 0200 Ethernet controller [Created at pci.281] Unique ID: 75la.5kj5EmCN2ND Parent ID: 1jkP.m50CK8FyreA SysFS ID: /devices/pci0000:00/0000:00:13.0/0000:80:00.1/0000:81:00.0 SysFS BusID: 0000:81:00.0 Hardware Class: network Model: "Agere ET-131x PCI-E Ethernet Controller" Vendor: pci 0x11c1 "Agere Systems" Device: pci 0xed00 "ET-131x PCI-E Ethernet Controller" SubVendor: pci 0x11c1 "Agere Systems" SubDevice: pci 0xed00 Revision: 0x01 Driver: "et131x" Driver Modules: "et131x" Device File: eth5 Memory Range: 0xfe800000-0xfe9fffff (rw,non-prefetchable) IRQ: 10 (4215 events) HW Address: 00:04:a7:05:da:03 Module Alias: "pci:v000011C1d0000ED00sv000011C1sd0000ED00bc02sc00i00" Driver Info #0: Driver Status: et131x is active Driver Activation Cmd: "modprobe et131x" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #10 (PCI bridge)
09: PCI 8200.0: 0200 Ethernet controller [Created at pci.281] Unique ID: gvUW.5kj5EmCN2ND Parent ID: AOFa.Fh3SrZ7FKGA SysFS ID: /devices/pci0000:00/0000:00:13.0/0000:80:00.0/0000:82:00.0 SysFS BusID: 0000:82:00.0 Hardware Class: network Model: "Agere ET-131x PCI-E Ethernet Controller" Vendor: pci 0x11c1 "Agere Systems" Device: pci 0xed00 "ET-131x PCI-E Ethernet Controller" SubVendor: pci 0x11c1 "Agere Systems" SubDevice: pci 0xed00 Revision: 0x01 Driver: "et131x" Driver Modules: "et131x" Device File: eth4 Memory Range: 0xfea00000-0xfebfffff (rw,non-prefetchable) IRQ: 10 (4215 events) HW Address: 00:04:a7:05:da:02 Module Alias: "pci:v000011C1d0000ED00sv000011C1sd0000ED00bc02sc00i00" Driver Info #0: Driver Status: et131x is active Driver Activation Cmd: "modprobe et131x" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #11 (PCI bridge)
lspci
81:00.0 Ethernet controller: Agere Systems ET-131x PCI-E Ethernet Controller (rev 01) 82:00.0 Ethernet controller: Agere Systems ET-131x PCI-E Ethernet Controller (rev 01)
If I just "modprobe et131x", the interfaces come up, but I only get 100 Mbit/s.
If I manually do "modprobe et131x et131x_speed_set=5", the interface says "NO CARRIER", although the cable is still plugged in.
I tried this with linux 2.6.18 and 2.6.24. Both give the same result.
Any help is much appreciated.
Regards Dominik
Sorry having bothered ...
Turns out it helps *a lot* to connect not only a gigabit switch but also a gigabit machine to test bandwidth.
Log in to post a comment.
Hi
with this hardware: http://www.linitx.com/viewproduct.php?prodid=11714 I only get the ET131x driver to run with 100 MBit in Half Duplex mode.
Details:
hwinfo --netcard (skipped the 8139 cards)
08: PCI 8100.0: 0200 Ethernet controller
[Created at pci.281]
Unique ID: 75la.5kj5EmCN2ND
Parent ID: 1jkP.m50CK8FyreA
SysFS ID: /devices/pci0000:00/0000:00:13.0/0000:80:00.1/0000:81:00.0
SysFS BusID: 0000:81:00.0
Hardware Class: network
Model: "Agere ET-131x PCI-E Ethernet Controller"
Vendor: pci 0x11c1 "Agere Systems"
Device: pci 0xed00 "ET-131x PCI-E Ethernet Controller"
SubVendor: pci 0x11c1 "Agere Systems"
SubDevice: pci 0xed00
Revision: 0x01
Driver: "et131x"
Driver Modules: "et131x"
Device File: eth5
Memory Range: 0xfe800000-0xfe9fffff (rw,non-prefetchable)
IRQ: 10 (4215 events)
HW Address: 00:04:a7:05:da:03
Module Alias: "pci:v000011C1d0000ED00sv000011C1sd0000ED00bc02sc00i00"
Driver Info #0:
Driver Status: et131x is active
Driver Activation Cmd: "modprobe et131x"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #10 (PCI bridge)
09: PCI 8200.0: 0200 Ethernet controller
[Created at pci.281]
Unique ID: gvUW.5kj5EmCN2ND
Parent ID: AOFa.Fh3SrZ7FKGA
SysFS ID: /devices/pci0000:00/0000:00:13.0/0000:80:00.0/0000:82:00.0
SysFS BusID: 0000:82:00.0
Hardware Class: network
Model: "Agere ET-131x PCI-E Ethernet Controller"
Vendor: pci 0x11c1 "Agere Systems"
Device: pci 0xed00 "ET-131x PCI-E Ethernet Controller"
SubVendor: pci 0x11c1 "Agere Systems"
SubDevice: pci 0xed00
Revision: 0x01
Driver: "et131x"
Driver Modules: "et131x"
Device File: eth4
Memory Range: 0xfea00000-0xfebfffff (rw,non-prefetchable)
IRQ: 10 (4215 events)
HW Address: 00:04:a7:05:da:02
Module Alias: "pci:v000011C1d0000ED00sv000011C1sd0000ED00bc02sc00i00"
Driver Info #0:
Driver Status: et131x is active
Driver Activation Cmd: "modprobe et131x"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #11 (PCI bridge)
lspci
81:00.0 Ethernet controller: Agere Systems ET-131x PCI-E Ethernet Controller (rev 01)
82:00.0 Ethernet controller: Agere Systems ET-131x PCI-E Ethernet Controller (rev 01)
If I just "modprobe et131x", the interfaces come up, but I only get 100 Mbit/s.
If I manually do "modprobe et131x et131x_speed_set=5", the interface says "NO CARRIER", although the cable is still plugged in.
I tried this with linux 2.6.18 and 2.6.24. Both give the same result.
Any help is much appreciated.
Regards
Dominik
Sorry having bothered ...
Turns out it helps *a lot* to connect not only a gigabit switch but also a gigabit machine to test bandwidth.