Re: [DIGImend-devel] Please Let Me know how to make driver
Brought to you by:
spb_nick
Menu
▾
▴
Re: [DIGImend-devel] Please Let Me know how to make driver
|
From: Masaru H. <mh...@ne...> - 2015-01-08 01:26:48
|
Hello Thanks Nick I am sorry I am in bed with flu. My doughter is down with influenza. Please give me more a week. I will check. There's a lot of flu going around now. Sorry Masaru Hirano Neoblast Inc. On 2015年01月01日 01:19, Nikolai Kondrashov wrote: > Hi Masaru, > > On 12/30/2014 12:44 PM, Masaru Hirano wrote: >> Thanks for your new driver. >> Ugee-1000-L works fine. > > Good. How did you verify it exactly? > Could you please provide evtest dumps of the pen coords test? > Did you have any special X.org configuration, like using the WizardPen > driver? > >> According to change of this case. >> I could found 4 changes by sources. >> But I can not adopt for other model. >> Please teach me how to fit for other models. >> All the product uses UC-LOGIC > > I assumed that all your models have the UC-Logic vendor ID (0x5543) and > either > the 0x45 or 0x81 product ID. If that's so, the driver should attempt to > handle > all of them and no further code change should be necessary. > > Do you have tablets with other VID:PID pairs? > >> So I have tried same way. >> Ugee-M708 model >> But this model does not work correctry. >> Please teach me how to add other model. >> M708 Model diagnostic files are attathched. >> This case strange output >> $xinput list > xinputlist.txt >> UC-LOIC is strange. > > "UC-LOIC" is a typo on behalf of the manufacturer. It's what they've put > into > their device and string descriptors themselves. > >> $ xinput list >> ⎡ Virtual core pointer id=2 [master pointer >> (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=10 [slave >> pointer (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=11 [slave >> pointer (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=12 [slave >> pointer (2)] >> >> I have tried M708 model diagnostic. > > Were these diagnostic files collected with the driver installed? The tablet > should work fine as the coordinate range seems to be full and correct. > Do you, > by any chance, still use the WizardPen driver? Could you please provide > evtest > dumps of the pen coords test for this tablet as well? > > Nick > > On 12/30/2014 12:44 PM, Masaru Hirano wrote: >> Hello Nick >> >> Thanks for your new driver. >> Ugee-1000-L works fine. >> >> According to change of this case. >> I could found 4 changes by sources. >> But I can not adopt for other model. >> Please teach me how to fit for other models. >> All the product uses UC-LOGIC >> >> 1.hid-huion.c >> these two codes are added. >> >> line228: >> case USB_DEVICE_ID_UGEE_TABLET_81: >> line229: >> case USB_DEVICE_ID_UGEE_TABLET_45: >> >> 2.hid-hion.c >> these two codes are added. >> line275: >> { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UGEE_TABLET_81) }, >> >> line276: >> { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC, USB_DEVICE_ID_UGEE_TABLET_45) }, >> >> 3.hid-ids.h >> these two codes are added. >> line:22 >> #define USB_DEVICE_ID_UGEE_TABLET_81 0x0081 >> line:22 >> #define USB_DEVICE_ID_UGEE_TABLET_45 0x0045 >> >> So I have tried same way. >> Ugee-M708 model >> But this model does not work correctry. >> Please teach me how to add other model. >> M708 Model diagnostic files are attathched. >> This case strange output >> $xinput list > xinputlist.txt >> UC-LOIC is strange. >> >> $ xinput list >> ⎡ Virtual core pointer id=2 [master pointer >> (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=10 [slave >> pointer (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=11 [slave >> pointer (2)] >> ⎜ ↳ UC-LOIC TABLET 1060 id=12 [slave >> pointer (2)] >> >> I have tried M708 model diagnostic. >> >> According to these way >> http://digimend.github.io/support/howto/trbl/diagnostics/ >> >> >> 1.Identify original model >> $ lsusb >> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 007 Device 002: ID 5543:0081 UC-Logic Technology Corp. >> Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 006 Device 003: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse >> Bus 006 Device 002: ID 0518:0001 EzKEY Corp. USB to PS2 Adaptor v1.09 >> Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> >> VID=5543 >> PID=0081 >> >> $ T=5543:0081 >> >> 2.Retrieve USB descriptors >> 1)sudo lsusb -v -d $T > descriptors.txt >> Bus 007 Device 002: ID 5543:0081 UC-Logic Technology Corp. >> Device Descriptor: >> bLength 18 >> bDescriptorType 1 >> bcdUSB 1.10 >> bDeviceClass 0 (Defined at Interface level) >> bDeviceSubClass 0 >> bDeviceProtocol 0 >> bMaxPacketSize0 64 >> idVendor 0x5543 UC-Logic Technology Corp. >> idProduct 0x0081 >> bcdDevice 0.00 >> iManufacturer 5 UC-LOIC >> iProduct 6 TABLET 1060 >> iSerial 0 >> bNumConfigurations 1 >> ^C >> >> 2) sudo usbhid-dump -ed -m $T > hid_report_descriptors.txt >> Bus 007 Device 002: ID 5543:0081 UC-Logic Technology Corp. >> Device Descriptor: >> bLength 18 >> bDescriptorType 1 >> bcdUSB 1.10 >> bDeviceClass 0 (Defined at Interface level) >> bDeviceSubClass 0 >> bDeviceProtocol 0 >> bMaxPacketSize0 64 >> idVendor 0x5543 UC-Logic Technology Corp. >> idProduct 0x0081 >> bcdDevice 0.00 >> iManufacturer 5 UC-LOIC >> iProduct 6 TABLET 1060 >> iSerial 0 >> bNumConfigurations 1 >> Configuration Descriptor: >> ^C >> >> >> 3.Collect raw input samples >> sudo usbhid-dump -es -m $T | tee frame_wheel_srolling.txt >> 007:002:000:STREAM 1418797530.559580 >> 07 80 84 01 75 01 00 00 >> >> 007:002:000:STREAM 1418797530.565550 >> 07 80 8B 01 6F 01 00 00 >> >> 007:002:000:STREAM 1418797530.573564 >> 07 80 94 01 68 01 00 00 >> >> 007:002:000:STREAM 1418797530.579546 >> 07 81 A0 01 5F 01 89 00 >> ^C >> >> 4.PEN >> $ sudo usbhid-dump -es -m $T | tee pen_coords.txt >> >> 4-1)Pen-Coordinate >> 07 80 82 55 F7 5A 00 00 >> >> 007:002:000:STREAM 1418797673.689610 >> 07 80 89 55 E0 5A 00 00 >> >> 007:002:000:STREAM 1418797673.695597 >> 07 80 91 55 C7 5A 00 00 >> >> 007:002:000:STREAM 1418797673.699593 >> 07 80 98 55 AD 5A 00 00 >> >> 007:002:000:STREAM 1418797673.705596 >> 07 80 9E 55 93 5A 00 00 >> ^C >> >> 4-2)Pen-Tiltangle >> $ sudo usbhid-dump -es -m $T | tee pen_tilt.txt >> Not Supported and skip >> >> >> 4-3)Pen-Pressure >> sudo usbhid-dump -es -m $T | tee pen_pressure.txt >> >> 007:002:000:STREAM 1418797836.355686 >> 07 80 2A 56 48 2D 00 00 >> >> 007:002:000:STREAM 1418797836.477668 >> 07 80 41 56 48 2D 00 00 >> >> 007:002:000:STREAM 1418797836.509667 >> 07 80 58 56 48 2D 00 00 >> >> 007:002:000:STREAM 1418797836.535662 >> 07 80 6B 56 48 2D 00 00 >> ^C >> >> 4-4)Pen-Buttons >> sudo usbhid-dump -es -m $T | tee pen_buttons.txt >> >> 007:002:000:STREAM 1418797957.023720 >> 07 80 9D 3C 37 2B 00 00 >> >> 007:002:000:STREAM 1418797957.169706 >> 07 80 BD 3C 37 2B 00 00 >> >> 007:002:000:STREAM 1418797957.547704 >> 07 80 BD 3C 56 2B 00 00 >> >> 007:002:000:STREAM 1418797957.831697 >> 07 80 DC 3C 56 2B 00 00 >> >> 007:002:000:STREAM 1418797957.855690 >> 07 80 FC 3C 56 2B 00 00 >> >> 007:002:000:STREAM 1418797957.871695 >> 07 80 16 3D 56 2B 00 00 >> >> 007:002:000:STREAM 1418797957.913699 >> 07 80 2E 3D 56 2B 00 00 >> >> >> 5 Frame Controls >> 5-1)Frame Controls Dials >> sudo usbhid-dump -es -m $T | tee frame_dials.txt >> >> Not Supported and skip >> >> 5-1)Frame Controls Buttons >> $ sudo usbhid-dump -es -m $T | tee frame_buttons.txt >> >> >> 007:002:002:STREAM 1418798804.272982 >> 03 04 3D 00 00 00 00 00 >> >> 007:002:002:STREAM 1418798804.792976 >> 03 00 00 00 00 00 00 00 >> >> 007:002:002:STREAM 1418798806.040974 >> 03 01 16 00 00 00 00 00 >> >> 007:002:002:STREAM 1418798806.496976 >> 03 00 00 00 00 00 00 00 >> >> 007:002:002:STREAM 1418798807.552979 >> 03 02 56 00 00 00 00 00 >> ^C >> >> >> 6.Mouse >> 6-1)Mouse-Coordinates >> $ sudo usbhid-dump -es -m $T | tee mouse_coords.txt >> Not Supported and skip >> >> 6-2)Mouse-Buttons >> $ sudo usbhid-dump -es -m $T | tee mouse_buttons.txt >> Not Supported and skip >> >> >> 6-3)Mouse-Wheel >> $ sudo usbhid-dump -es -m $T | tee mouse_wheel.txt >> Not Supported and skip >> >> 7.huion-probe >> 7-1)Identify original model >> $ lsusb > identmodel.txt >> Bus 007 Device 002: ID 5543:0081 UC-Logic Technology Corp. >> bus=7 >> device=2 >> >> 7-2)huion-probe >> $ sudo huion-probe 7 2 > ~/huionprobe.txt >> >> M 55 00 43 00 2D 00 4C 00 4F 00 49 00 43 00 00 00 >> P 54 00 41 00 42 00 4C 00 45 00 54 00 20 00 31 00 30 00 36 00 30 00 >> S 64 0E 03 40 9C C0 5D 03 00 FF 07 A0 0F 08 00 >> S 65 04 03 20 A0 >> S 6E 04 03 30 00 >> S 79 28 03 44 00 46 00 53 00 2D 00 55 00 49 00 20 00 46 00 34 00 30 00 >> 31 00 2D 00 32 00 30 00 31 00 31 00 31 00 30 00 32 00 >> S 7A 08 03 01 08 00 00 00 00 >> >> 7-2)huion-decode >> $ sudo huion-probe 6 3 | huion-decode > ~/huiondecode.txt >> Manufacturer: UC-LOIC? >> Product: TABLET 1060 >> Max X: 40000 >> Max Y: 24000 >> Max pressure: 2047 >> Resolution: 4000 >> Internal model: DFS-UI F401-2011102 >> >> >> 7-2)Calculation >> Active Area 10"x6" >> MaxX / Width = MaxY / Height = Resolution >> >> *40000/Width =4000 >> hence Width=10 >> >> *24000/Height=4000 >> hence Height=6 >> >> Best regards, >> Masaru Hirano >> Neoblast Inc. >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> On 2014年12月15日 02:00, Nikolai Kondrashov wrote: >>> Hi Masaru, >>> >>> On 11/06/2014 07:30 AM, Masaru Hirano wrote: >>>> Hello Nick >>>> >>>> Thanks for your support. >>>> We are Ugee distributer in japan. >>>> Please let us know how to make driver. >>>> >>>> We would like to build ugee tablet driver. >>>> VID=5543 >>>> PID=0081 >>>> These are all fine. >>>> VID=5543 >>>> PID=0045 >>>> These are not work fine. >>>> Calibration does not been succeed. >>> >>> I've made a very simple change to the digimend-kernel-drivers package, >>> which >>> has a slight possibility of making them work. I've simply added both >>> of the >>> product IDs you sent to the list of devices supported by the hid-huion >>> driver, >>> so it would treat them exactly as Huion tablets. >>> >>> The change is available in the "ugee" branch on GitHub, which you can >>> download >>> here: >>> https://github.com/DIGImend/digimend-kernel-drivers/archive/ugee.zip >>> >>> Please try building, installing and using the driver with your >>> tablets. We >>> might just be lucky and they might work. >>> >>> Nick >>> >>> On 11/06/2014 07:30 AM, Masaru Hirano wrote: >>>> Hello Nick >>>> >>>> Thanks for your support. >>>> We are Ugee distributer in japan. >>>> Please let us know how to make driver. >>>> >>>> We would like to build ugee tablet driver. >>>> VID=5543 >>>> PID=0081 >>>> These are all fine. >>>> VID=5543 >>>> PID=0045 >>>> These are not work fine. >>>> Calibration does not been succeed. >>>> >>>> If you give me some procedure and tools for making tablet and tablet >>>> monitor driver. >>>> I would like to make. >>>> Under ubuntu studio 14.04 >>>> >>>> File 1: >>>> VID=5543 >>>> PID=0081 >>>> are work fine. >>>> >>>> File 2: >>>> We would like to build for them. >>>> >>>> We are small company of system integrator for creative buginners. >>>> So we need to provide no wacom tablet and ubuntu-studio 14.04 for >>>> cost effective in Japan. >>>> >>>> Ofcource when we made new driver, we will share for everyone. >>>> >>>> Best regards, >>>> Masaru Hirano >>>> Neoblast Inc. >>>> >>>> On 2014年11月05日 18:24, Nikolai Kondrashov wrote: >>>>> On 11/05/2014 11:22 AM, Nikolai Kondrashov wrote: >>>>>> We would appreciate it, if you could provide us with a list of Ugee >>>>>> tablets >>>>>> which you found working with our tablets >>>>> >>>>> I meant "our drivers", of course. >>>>> >>>>> Nick >>>>> >>>>> On 11/05/2014 11:22 AM, Nikolai Kondrashov wrote: >>>>>> Hello Masaru, >>>>>> >>>>>> I'm very glad to hear that another tablet distributor is choosing to >>>>>> contribute their effort to making Linux drivers for their tablets. >>>>>> >>>>>> This year Yiynova helped with drivers for their tablets as well, and >>>>>> now have >>>>>> a bunch of models supported. >>>>>> >>>>>> We would appreciate it, if you could provide us with a list of Ugee >>>>>> tablets >>>>>> which you found working with our tablets, along with their USB >>>>>> VID:PID >>>>>> pairs, >>>>>> so we can add them to the list and advertise their support. >>>>>> >>>>>> Regarding the so far unsupported tablets, I would also like to know >>>>>> their >>>>>> names and VID:PID pairs, along with their parameters (if those are >>>>>> unavailable >>>>>> on the web). I would also like to know which hardware they're based >>>>>> on, if >>>>>> possible. Is it UC-Logic, Waltop, anything else? >>>>>> >>>>>> This would get us started. >>>>>> >>>>>> Thank you. >>>>>> >>>>>> Sincerely, >>>>>> Nick >>>>>> >>>>>> On 11/05/2014 03:42 AM, Masaru Hirano wrote: >>>>>>> Hello developper >>>>>>> >>>>>>> We are neoblast inc japan. >>>>>>> We are one of Ugee Distributer. >>>>>>> >>>>>>> There are few driver for ugee. >>>>>>> Most of product work by digemend kernel driver. >>>>>>> But some product (tablet monitor, sketch=pad) do not work. >>>>>>> http://ugee.net/index.asp >>>>>>> >>>>>>> We use ubuntu-studio 14.04. >>>>>>> >>>>>>> Digemend kernel driver are not enough for us. >>>>>>> There are no friver for tablet monitor for ubuntu 14.04. >>>>>>> >>>>>>> We would like to build by ourseleves. >>>>>>> Please let us know how to make kernel driver. >>>>>>> >>>>>>> best regards, >>>>>>> Masaru Hirano >>>>>>> neoblast inc. >>>>> >>>>> >>>>> >>> >>> >>> >> > > > -- ========================================= Masaru Hirano Neoblast Inc. Tokiwadai1-67-5-704, Itabashi-ku, Tokyo, Japan ZIP:174-0071 E-Mail:mh...@ne... Tel:+81-3-4570-7345 Mob:+81-70-6575-1732 Fax:+81-20-4623-9249 ========================================= |
