Re: [DIGImend-devel] Tablet issue

[Jake W. <jcm...@ho...>]

Hey Vince,
Thanks for the comment, I actually have the extension pack installed and checked for use (for usb 2.0 devices, right?), the VM reports no usb devices are connected, and I don't see the tablet within the windows device manager either (http://i.imgur.com/UQvU8Uz.png)
But it's okay I'd rather not bring a totally unrelated problem up when I actually have access to a windows machine!

Date: Sun, 30 Nov 2014 16:48:10 -0500
Subject: Re: [DIGImend-devel] Tablet issue
From: Vi...@Pl...
To: jcm...@ho...
CC: dig...@li...; sp...@gm...

You have to install the virtualbox usb extension.  See the web page.  I was told to not use my distro install but to use the virtualbox web page.  Worked like a charm
------------

Vince
On Nov 30, 2014 3:42 PM, "Jake Waffle" <jcm...@ho...> wrote:



That sucks to hear.
I do have windows running through virtualbox, however it never recognised my tablet (I tried it as an alternative since it's not working), but then again I don't have experience using VM's so.
I'll try and set the tablet up on an old laptop running windows, or some time in the future reinstall windows on this machine.
If you could give me a run down of what I'll need to do I can try it out tomorrow on the laptop, if you don't mind anyway. 

Cheers for trying to help thus far.

> Date: Sun, 30 Nov 2014 21:56:34 +0200
> From: sp...@gm...
> To: jcm...@ho...
> CC: dig...@li...
> Subject: Re: Tablet issue
> 
> On 11/30/2014 08:38 PM, Jake Waffle wrote:
> > Attached the full output from doing what was done in the video,
> 
> Thanks!
> 
> >  > Could you please describe how the tablet behaves at the moment?
> > The tablet behaves the same as I originally reported, it can click, the pen
> > buttons work and the side buttons seem to work (I never used them
> > previously, but using them here produces what they are set to do).
> >
> > The only problem is still not being able to move the cursor with the pen
> > (not sure about pen pressure).
> 
> Alright, it seems the tablet doesn't report the full resolution after all.
> So the hid-huion driver attempt to enable it has failed. To make this tablet
> work we'll have to figure out what enables it.
> 
> Doing that won't be easy. You'll need a Windows installation. Either a native
> one, or in a VM under Linux. You'll need to capture USB traffic going between
> the tablet and your tablet driver for Windows when the tablet is plugged in.
> 
> You can do it with Wireshark running on the Linux host (in case of VM
> install), or on Windows (in case of native install).
> 
> After you captured the traffic, it will need to be inspected to find exactly
> what packet (sequence of packets) enables full resolution, with which I can
> help.
> 
> Nick
> 
> On 11/30/2014 08:38 PM, Jake Waffle wrote:
> > Attached the full output from doing what was done in the video,
> >
> >  > Could you please describe how the tablet behaves at the moment?
> > The tablet behaves the same as I originally reported, it can click, the pen buttons work and the side buttons seem to work (I never used them previously, but using them here produces what they are set to do).
> >
> > The only problem is still not being able to move the cursor with the pen (not sure about pen pressure).
> >
> >  > Date: Sun, 30 Nov 2014 20:17:24 +0200
> >  > From: sp...@gm...
> >  > To: jcm...@ho...
> >  > CC: dig...@li...
> >  > Subject: Re: Tablet issue
> >  >
> >  > On 11/30/2014 07:05 PM, Jake Waffle wrote:
> >  > > Apologies if it's too much output, It's only a portion though.
> >  >
> >  > There's supposed to be a lot of it, not a problem. Thank you.
> >  >
> >  > Without considering where the pen actually was, this looks OK.
> >  >
> >  > Could you please describe how the tablet behaves at the moment?
> >  >
> >  > Also, to make sure we get full resolution, could you please send me (full,
> >  > compressed) output of the same command when you do strokes outwards tablet
> >  > surface, crossing each working area border in turn, like shown in this video:
> >  >
> >  > https://www.youtube.com/watch?v=ysYk8KLY98U
> >  >
> >  > Thank you.
> >  >
> >  > On 11/30/2014 07:05 PM, Jake Waffle wrote:
> >  > > Hey Nick,
> >  > >
> >  > > No problems at all, A-OK.
> >  > > Apologies if it's too much output, It's only a portion though.
> >  > >
> >  > > Let me know if there's anything else!
> >  > >
> >  > >
> >  > > [jake@localhost ~]$ sudo bash -c 'ls /sys/kernel/debug/hid/0003:5543:0781.*/events | head -n1 | xargs cat'
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c5 03 15 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 965
> >  > > GenericDesktop.Y = 1301
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c6 03 15 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 966
> >  > > GenericDesktop.Y = 1301
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c7 03 14 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 967
> >  > > GenericDesktop.Y = 1300
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c8 03 14 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 968
> >  > > GenericDesktop.Y = 1300
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c8 03 13 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 968
> >  > > GenericDesktop.Y = 1299
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 c9 03 13 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 969
> >  > > GenericDesktop.Y = 1299
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 ca 03 13 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 970
> >  > > GenericDesktop.Y = 1299
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 ca 03 12 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 970
> >  > > GenericDesktop.Y = 1298
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 cb 03 12 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 971
> >  > > GenericDesktop.Y = 1298
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 cc 03 12 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 972
> >  > > GenericDesktop.Y = 1298
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 cd 03 12 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 973
> >  > > GenericDesktop.Y = 1298
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 ce 03 11 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 974
> >  > > GenericDesktop.Y = 1297
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 cf 03 11 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 975
> >  > > GenericDesktop.Y = 1297
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d0 03 10 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 976
> >  > > GenericDesktop.Y = 1296
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d1 03 10 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 977
> >  > > GenericDesktop.Y = 1296
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d2 03 10 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 978
> >  > > GenericDesktop.Y = 1296
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d3 03 0f 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 979
> >  > > GenericDesktop.Y = 1295
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d4 03 0f 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 980
> >  > > GenericDesktop.Y = 1295
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d5 03 0e 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 981
> >  > > GenericDesktop.Y = 1294
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d6 03 0e 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 982
> >  > > GenericDesktop.Y = 1294
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d7 03 0d 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 983
> >  > > GenericDesktop.Y = 1293
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 00 d8 03 0d 05 00 00
> >  > > Button.0001 = 0
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 984
> >  > > GenericDesktop.Y = 1293
> >  > > Digitizers.TipPressure = 0
> >  > >
> >  > > report (size 8) (numbered) = 09 01 d9 03 0d 05 d3 00
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 985
> >  > > GenericDesktop.Y = 1293
> >  > > Digitizers.TipPressure = 211
> >  > >
> >  > > report (size 8) (numbered) = 09 01 d9 03 0d 05 ff 00
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 985
> >  > > GenericDesktop.Y = 1293
> >  > > Digitizers.TipPressure = 255
> >  > >
> >  > > report (size 8) (numbered) = 09 01 d9 03 0c 05 23 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 985
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 291
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 3b 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 315
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 4c 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 332
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 5a 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 346
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 68 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 360
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 71 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 369
> >  > >
> >  > > report (size 8) (numbered) = 09 01 da 03 0c 05 7b 01
> >  > > Button.0001 = 1
> >  > > Button.0002 = 0
> >  > > Button.0003 = 0
> >  > > GenericDesktop.X = 986
> >  > > GenericDesktop.Y = 1292
> >  > > Digitizers.TipPressure = 379
> >  > >
> >  > >
> >  > >
> >  > > > Date: Sun, 30 Nov 2014 16:26:33 +0200
> >  > > > From: sp...@gm...
> >  > > > To: jcm...@ho...
> >  > > > CC: dig...@li...
> >  > > > Subject: Re: Tablet issue
> >  > > >
> >  > > > Hi Jake,
> >  > > >
> >  > > > Sorry for the delay with the answer. I've been quite busy this week.
> >  > > >
> >  > > > Thanks for the outputs. The driver seems to bind correctly, at least.
> >  > > >
> >  > > > Now, could you please send me a piece of output of this command:
> >  > > >
> >  > > > sudo bash -c 'ls /sys/kernel/debug/hid/0003:5543:0781.*/events | head -n1 | xargs cat'
> >  > > >
> >  > > > while making a stroke with the tablet pen?
> >  > > >
> >  > > > This will show what the tablet sends and how the kernel interprets the
> >  > > > reports.
> >  > > >
> >  > > > Thank you.
> >  > > >
> >  > > > Nick
> >  > > >
> >  > > > On 11/24/2014 04:10 AM, Jake Waffle wrote:
> >  > > > > Hmm. After using the command and noticing nothing, I did another reboot and still nothing.
> >  > > > >
> >  > > > > [jake@localhost ~]$ modinfo hid-huion
> >  > > > > filename: /lib/modules/3.17.3-300.fc21.x86_64/extra/hid-huion.ko
> >  > > > > version: 5
> >  > > > > license: GPL
> >  > > > > description: Huion HID driver
> >  > > > > author: Nikolai Kondrashov
> >  > > > > author: Martin Rusko
> >  > > > > srcversion: B0934C93201C94470057FEC
> >  > > > > alias: hid:b0003g*v00005543p00000781
> >  > > > > alias: hid:b0003g*v00005543p0000004D
> >  > > > > alias: hid:b0003g*v00005543p0000006E
> >  > > > > alias: hid:b0003g*v0000256Cp0000006E
> >  > > > > depends:
> >  > > > > vermagic: 3.17.3-300.fc21.x86_64 SMP mod_unload
> >  > > > >
> >  > > > > [jake@localhost ~]$ modinfo hid-uclogic
> >  > > > > filename: /lib/modules/3.17.3-300.fc21.x86_64/extra/hid-uclogic.ko
> >  > > > > version: 5
> >  > > > > license: GPL
> >  > > > > srcversion: 2C10D4F9392C02ACFC75150
> >  > > > > alias: hid:b0003g*v00005543p00000522
> >  > > > > alias: hid:b0003g*v00005543p00000064
> >  > > > > alias: hid:b0003g*v00005543p00000005
> >  > > > > alias: hid:b0003g*v00005543p00000004
> >  > > > > alias: hid:b0003g*v00005543p00000003
> >  > > > > alias: hid:b0003g*v00005543p00000042
> >  > > > > depends:
> >  > > > > vermagic: 3.17.3-300.fc21.x86_64 SMP mod_unload
> >  > > > >
> >  > > > > [jake@localhost ~]$ ls -l /sys/bus/hid/devices/0003:5543:0781.*/driver
> >  > > > > lrwxrwxrwx. 1 root root 0 Nov 24 02:00 /sys/bus/hid/devices/0003:5543:0781.0004/driver -> ../../../../../../../bus/hid/drivers/huion
> >  > > > > lrwxrwxrwx. 1 root root 0 Nov 24 02:00 /sys/bus/hid/devices/0003:5543:0781.0005/driver -> ../../../../../../../bus/hid/drivers/huion
> >  > > > > lrwxrwxrwx. 1 root root 0 Nov 24 02:00 /sys/bus/hid/devices/0003:5543:0781.0006/driver -> ../../../../../../../bus/hid/drivers/huion
> >  > > > > [jake@localhost ~]$
> >  > > > >
> >  > > > >
> >  > > > >
> >  > > > >
> >  > > > > > Date: Mon, 24 Nov 2014 00:03:26 +0200
> >  > > > > > From: sp...@gm...
> >  > > > > > To: jcm...@ho...
> >  > > > > > CC: dig...@li...
> >  > > > > > Subject: Re: Tablet issue
> >  > > > > >
> >  > > > > > On 11/23/2014 09:14 PM, Jake Waffle wrote:
> >  > > > > > > Thanks for getting back to me!
> >  > > > > > >
> >  > > > > > > So... (sigh), I believe I had installed this previously, so I ran
> >  > > > > > > 'sudo rmmod hid-huion' and proceeded to 'make install'
> >  > > > > > >
> >  > > > > > > [jake@localhost digimend-kernel-drivers-twha60]$ sudo make install
> >  > > > > > > make -C /lib/modules/3.17.3-300.fc21.x86_64/build SUBDIRS=/home/jake/Downloads/digimend-kernel-drivers-twha60 modules_install
> >  > > > > > > make[1]: Entering directory '/usr/src/kernels/3.17.3-300.fc21.x86_64'
> >  > > > > > > INSTALL /home/jake/Downloads/digimend-kernel-drivers-twha60/hid-huion.ko
> >  > > > > > > Can't read private key
> >  > > > > > > INSTALL /home/jake/Downloads/digimend-kernel-drivers-twha60/hid-uclogic.ko
> >  > > > > > > Can't read private key
> >  > > > > > > DEPMOD 3.17.3-300.fc21.x86_64
> >  > > > > > > make[1]: Leaving directory '/usr/src/kernels/3.17.3-300.fc21.x86_64'
> >  > > > > > > install -D -m 0644 digimend.conf /etc/depmod.d/digimend.conf
> >  > > > > > > depmod -a
> >  > > > > > > install hid-rebind /sbin/hid-rebind
> >  > > > > > > install -m 0644 hid-rebind.rules /lib/udev/rules.d/70-hid-rebind.rules
> >  > > > > > > udevadm control --reload
> >  > > > > > >
> >  > > > > > > Unplugged tablet/restarted. It hasn't done anything towards the issue, perhaps I've foolishly not installed it correctly?
> >  > > > > > > Apologies for the hassle.
> >  > > > > >
> >  > > > > > Um, unless you rebooted, then the tablet likely got handled by the already
> >  > > > > > loaded hid-uclogic. Try rebooting, or doing "sudo rmmod hid-uclogic".
> >  > > > > > I should've mentioned it.
> >  > > > > >
> >  > > > > > If that doesn't help, could you please send the output of the following
> >  > > > > > commands?
> >  > > > > >
> >  > > > > > modinfo hid-huion
> >  > > > > > modinfo hid-uclogic
> >  > > > > > ls -l /sys/bus/hid/devices/0003:5543:0781.*/driver
> >  > > > > >
> >  > > > > > Thank you.
> >  > > > > >
> >  > > > > > Nick
> >  > > > > >
> >  > > > > > On 11/23/2014 09:14 PM, Jake Waffle wrote:
> >  > > > > > > Thanks for getting back to me!
> >  > > > > > >
> >  > > > > > > So... (sigh), I believe I had installed this previously, so I ran
> >  > > > > > > 'sudo rmmod hid-huion' and proceeded to 'make install'
> >  > > > > > >
> >  > > > > > > [jake@localhost digimend-kernel-drivers-twha60]$ sudo make install
> >  > > > > > > make -C /lib/modules/3.17.3-300.fc21.x86_64/build SUBDIRS=/home/jake/Downloads/digimend-kernel-drivers-twha60 modules_install
> >  > > > > > > make[1]: Entering directory '/usr/src/kernels/3.17.3-300.fc21.x86_64'
> >  > > > > > > INSTALL /home/jake/Downloads/digimend-kernel-drivers-twha60/hid-huion.ko
> >  > > > > > > Can't read private key
> >  > > > > > > INSTALL /home/jake/Downloads/digimend-kernel-drivers-twha60/hid-uclogic.ko
> >  > > > > > > Can't read private key
> >  > > > > > > DEPMOD 3.17.3-300.fc21.x86_64
> >  > > > > > > make[1]: Leaving directory '/usr/src/kernels/3.17.3-300.fc21.x86_64'
> >  > > > > > > install -D -m 0644 digimend.conf /etc/depmod.d/digimend.conf
> >  > > > > > > depmod -a
> >  > > > > > > install hid-rebind /sbin/hid-rebind
> >  > > > > > > install -m 0644 hid-rebind.rules /lib/udev/rules.d/70-hid-rebind.rules
> >  > > > > > > udevadm control --reload
> >  > > > > > >
> >  > > > > > > Unplugged tablet/restarted. It hasn't done anything towards the issue, perhaps I've foolishly not installed it correctly?
> >  > > > > > > Apologies for the hassle.
> >  > > > > > >
> >  > > > > > > > Date: Sun, 23 Nov 2014 20:46:55 +0200
> >  > > > > > > > From: sp...@gm...
> >  > > > > > > > To: jcm...@ho...
> >  > > > > > > > CC: dig...@li...
> >  > > > > > > > Subject: Re: Tablet issue
> >  > > > > > > >
> >  > > > > > > > On 11/23/2014 07:17 PM, Jake Waffle wrote:
> >  > > > > > > > > I had tried ./bootstrap too, however it produced the same 'No such file or
> >  > > > > > > > > directory' message, I can never seem to navigate the git site correctly,
> >  > > > > > > > > thanks for the link to that page.
> >  > > > > > > >
> >  > > > > > > > Hmm, that's strange.
> >  > > > > > > >
> >  > > > > > > > > The rpm works for me.
> >  > > > > > > >
> >  > > > > > > > Great!
> >  > > > > > > >
> >  > > > > > > > > [jake@localhost ~]$ sudo huion-probe 5 5
> >  > > > > > > > > [sudo] password for jake:
> >  > > > > > > > > M 55 00 43 00 2D 00 4C 00 4F 00 47 00 49 00 43 00
> >  > > > > > > > > P 54 00 57 00 48 00 41 00 36 00 30 00
> >  > > > > > > > > S 64 0E 03 40 9C A8 61 03 00 FF 07 A0 0F 08 00
> >  > > > > > > > > S 65 04 03 00 71
> >  > > > > > > > > S 6E 04 03 30 00
> >  > > > > > > > > S 79 14 03 48 00 41 00 36 00 30 00 2D 00 46 00 34 00 30 00 31 00
> >  > > > > > > > > S 7A 08 03 01 08 00 00 00 00
> >  > > > > > > >
> >  > > > > > > > Nice, it works!
> >  > > > > > > >
> >  > > > > > > > > Running huion-decode seems to just sit there, unless it's supposed to take
> >  > > > > > > > > more than 10 mins.
> >  > > > > > > >
> >  > > > > > > > Huion-decode is expecting huion-probe output on its input. For your
> >  > > > > > > > huion-probe output it produces this:
> >  > > > > > > >
> >  > > > > > > > Manufacturer: UC-LOGIC
> >  > > > > > > > Product: TWHA60
> >  > > > > > > > Max X: 40000
> >  > > > > > > > Max Y: 25000
> >  > > > > > > > Max pressure: 2047
> >  > > > > > > > Resolution: 4000
> >  > > > > > > > Internal model: HA60-F401
> >  > > > > > > >
> >  > > > > > > > Which shows it's decoding it fine.
> >  > > > > > > >
> >  > > > > > > > > The cursor now moves when moving the pen on and off the tablet, but does not
> >  > > > > > > > > move consistently as you'd expect, it requires a sort of big flick to move.
> >  > > > > > > >
> >  > > > > > > > This is expected when report descriptor is not fixed which is the work of a
> >  > > > > > > > kernel driver.
> >  > > > > > > >
> >  > > > > > > > > I'm assuming it's the side effect of proprietary mode as mentioned?
> >  > > > > > > >
> >  > > > > > > > Yes.
> >  > > > > > > >
> >  > > > > > > > I've made a branch of digimend-kernel-drivers which has a change moving your
> >  > > > > > > > tablet under the hid-huion driver. It is very likely to make it work.
> >  > > > > > > >
> >  > > > > > > > You can download it here:
> >  > > > > > > > https://github.com/DIGImend/digimend-kernel-drivers/archive/twha60.zip
> >  > > > > > > >
> >  > > > > > > > Follow the instructions in README.md to install the driver.
> >  > > > > > > >
> >  > > > > > > > Nick
> >  > > > > > > >
> >  > > > > > > > On 11/23/2014 07:17 PM, Jake Waffle wrote:
> >  > > > > > > > > I had tried ./bootstrap too, however it produced the same 'No such file or directory' message, I can never seem to navigate the git site correctly, thanks for the link to that page. The rpm works for me.
> >  > > > > > > > >
> >  > > > > > > > > [jake@localhost ~]$ sudo huion-probe 5 5
> >  > > > > > > > > [sudo] password for jake:
> >  > > > > > > > > M 55 00 43 00 2D 00 4C 00 4F 00 47 00 49 00 43 00
> >  > > > > > > > > P 54 00 57 00 48 00 41 00 36 00 30 00
> >  > > > > > > > > S 64 0E 03 40 9C A8 61 03 00 FF 07 A0 0F 08 00
> >  > > > > > > > > S 65 04 03 00 71
> >  > > > > > > > > S 6E 04 03 30 00
> >  > > > > > > > > S 79 14 03 48 00 41 00 36 00 30 00 2D 00 46 00 34 00 30 00 31 00
> >  > > > > > > > > S 7A 08 03 01 08 00 00 00 00
> >  > > > > > > > >
> >  > > > > > > > > Running huion-decode seems to just sit there, unless it's supposed to take more than 10 mins.
> >  > > > > > > > >
> >  > > > > > > > > The cursor now moves when moving the pen on and off the tablet, but does not move consistently as you'd expect, it requires a sort of big flick to move.
> >  > > > > > > > > I'm assuming it's the side effect of proprietary mode as mentioned?
> >  > > > > > > > >
> >  > > > > > > > >
> >  > > > > > > > > > Date: Sun, 23 Nov 2014 18:59:08 +0200
> >  > > > > > > > > > From: sp...@gm...
> >  > > > > > > > > > To: jcm...@ho...
> >  > > > > > > > > > CC: DIG...@li...
> >  > > > > > > > > > Subject: Re: Tablet issue
> >  > > > > > > > > >
> >  > > > > > > > > > I'm copying the maillist anyway, as others might be encountering the same
> >  > > > > > > > > > problem.
> >  > > > > > > > > >
> >  > > > > > > > > > On 11/23/2014 06:52 PM, Jake Waffle wrote:
> >  > > > > > > > > > > Hi Nick,
> >  > > > > > > > > > >
> >  > > > > > > > > > > Apologies... I don't seem to be able to set huion-tools up (I won't post
> >  > > > > > > > > > > this bit to the archive considering it's likely me just not knowing).
> >  > > > > > > > > > > Installation states to use the ./configure, however after a quick search I'm
> >  > > > > > > > > > > suggested I should be using autoconf first?
> >  > > > > > > > > > >
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ ./configure
> >  > > > > > > > > > > bash: ./configure: No such file or directory
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ autoconf
> >  > > > > > > > > > > configure.ac:24: error: possibly undefined macro: AM_INIT_AUTOMAKE
> >  > > > > > > > > > > If this token and others are legitimate, please use m4_pattern_allow.
> >  > > > > > > > > > > See the Autoconf documentation.
> >  > > > > > > > > > > configure.ac:25: error: possibly undefined macro: AM_MAINTAINER_MODE
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ ./configure
> >  > > > > > > > > > > ./configure: line 1849: syntax error near unexpected token `1.9'
> >  > > > > > > > > > > ./configure: line 1849: `AM_INIT_AUTOMAKE(1.9 -Wall foreign)'
> >  > > > > > > > > >
> >  > > > > > > > > > If you want to build from the git tree (as downloaded using the "Download ZIP"
> >  > > > > > > > > > link on the right), you should execute ./bootstrap first (as mentioned shortly
> >  > > > > > > > > > in README.md).
> >  > > > > > > > > >
> >  > > > > > > > > > However, you might be better off downloading and building a release tarball
> >  > > > > > > > > > (preferably latest, v3 [1]), or downloading and installing a release rpm or
> >  > > > > > > > > > deb package.
> >  > > > > > > > > >
> >  > > > > > > > > > > Sorry.
> >  > > > > > > > > >
> >  > > > > > > > > > Nothing to feel sorry about :)
> >  > > > > > > > > >
> >  > > > > > > > > > Nick
> >  > > > > > > > > >
> >  > > > > > > > > > [1] https://github.com/DIGImend/huion-tools/releases/tag/v3
> >  > > > > > > > > >
> >  > > > > > > > > > On 11/23/2014 06:52 PM, Jake Waffle wrote:
> >  > > > > > > > > > > Hi Nick,
> >  > > > > > > > > > >
> >  > > > > > > > > > > Apologies... I don't seem to be able to set huion-tools up (I won't post this bit to the archive considering it's likely me just not knowing).
> >  > > > > > > > > > > Installation states to use the ./configure, however after a quick search I'm suggested I should be using autoconf first?
> >  > > > > > > > > > >
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ ./configure
> >  > > > > > > > > > > bash: ./configure: No such file or directory
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ autoconf
> >  > > > > > > > > > > configure.ac:24: error: possibly undefined macro: AM_INIT_AUTOMAKE
> >  > > > > > > > > > > If this token and others are legitimate, please use m4_pattern_allow.
> >  > > > > > > > > > > See the Autoconf documentation.
> >  > > > > > > > > > > configure.ac:25: error: possibly undefined macro: AM_MAINTAINER_MODE
> >  > > > > > > > > > > [jake@localhost huion-tools-master]$ ./configure
> >  > > > > > > > > > > ./configure: line 1849: syntax error near unexpected token `1.9'
> >  > > > > > > > > > > ./configure: line 1849: `AM_INIT_AUTOMAKE(1.9 -Wall foreign)'
> >  > > > > > > > > > >
> >  > > > > > > > > > > Sorry.
> >  > > > > > > > > > >
> >  > > > > > > > > > >
> >  > > > > > > > > > >
> >  > > > > > > > > > > > Date: Sun, 23 Nov 2014 17:43:02 +0200
> >  > > > > > > > > > > > From: sp...@gm...
> >  > > > > > > > > > > > To: jcm...@ho...
> >  > > > > > > > > > > > CC: DIG...@li...
> >  > > > > > > > > > > > Subject: Re: Tablet issue
> >  > > > > > > > > > > >
> >  > > > > > > > > > > > > Could you please try running huion-probe [1] on this tablet (don't be confused
> >  > > > > > > > > > > > > by the name, Huion tablets are mostly UC-Logic tablets inside) and seeing if
> >  > > > > > > > > > > > > it works/produces any output? Perhaps we'll be able to handle your tablet in
> >  > > > > > > > > > > > > our hid-huion driver, as part of the digimend-kernel-drivers package.
> >  > > > > > > > > > > >
> >  > > > > > > > > > > > And here is the link to huion-tools which contain huion-probe:
> >  > > > > > > > > > > >
> >  > > > > > > > > > > > [1] https://github.com/DIGImend/huion-tools
> >  > > > > > > > > > > >
> >  > > > > > > > > > > > On 11/23/2014 05:39 PM, Nikolai Kondrashov wrote:
> >  > > > > > > > > > > > > Hi Jake,
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > I'm copying the answer to the digimend-devel maillist to keep archive and have
> >  > > > > > > > > > > > > others posted. Please use "Reply to all" when replying.
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > On 11/21/2014 06:08 AM, Jake Waffle wrote:
> >  > > > > > > > > > > > >> Hello,
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> I currently own a Monoprice tablet, specifically "Monoprice MP1060-HA60",
> >  > > > > > > > > > > > >> which is a rebranded "UC-Logic Tablet TWHA60". On your support page it
> >  > > > > > > > > > > > >> mentions the drivers for this are in development, but also states it's
> >  > > > > > > > > > > > >> supported in the latest kernels.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> The tablet doesn't seem to work for me, it is able to act as a mouse in
> >  > > > > > > > > > > > >> terms of clicking, the buttons on the pen seem to work and at least two
> >  > > > > > > > > > > > >> side-buttons (close and save) work, however I cannot move the cursor with
> >  > > > > > > > > > > > >> the pen. Pressing the pen against the tablet doesn't indicate any pressure
> >  > > > > > > > > > > > >> either.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> I'm honestly a 'noob' linux user and I run the latest Fedora. I've included
> >  > > > > > > > > > > > >> diagnostics, however 'frame_buttons', 'frame_wheel_srolling', 'pen_buttons',
> >  > > > > > > > > > > > >> 'pen_coords', 'pen_pressure' and 'pen_tilt' produced empty documents.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> Any help/advice would be appreciated.
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > This is the third version of this tablet I see and the first one with three
> >  > > > > > > > > > > > > interfaces. One older model was made to work, IIRC. The newer ones weren't
> >  > > > > > > > > > > > > catered to yet.
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > Could you please try running huion-probe [1] on this tablet (don't be confused
> >  > > > > > > > > > > > > by the name, Huion tablets are mostly UC-Logic tablets inside) and seeing if
> >  > > > > > > > > > > > > it works/produces any output? Perhaps we'll be able to handle your tablet in
> >  > > > > > > > > > > > > our hid-huion driver, as part of the digimend-kernel-drivers package.
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > Nick
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > > > On 11/21/2014 06:08 AM, Jake Waffle wrote:
> >  > > > > > > > > > > > >> Hello,
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> I currently own a Monoprice tablet, specifically "Monoprice MP1060-HA60", which is a rebranded "UC-Logic Tablet TWHA60". On your support page it mentions the drivers for this are in development, but also states it's supported in the latest kernels.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> The tablet doesn't seem to work for me, it is able to act as a mouse in terms of clicking, the buttons on the pen seem to work and at least two side-buttons (close and save) work, however I cannot move the cursor with the pen. Pressing the pen against the tablet doesn't indicate any pressure either.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> I'm honestly a 'noob' linux user and I run the latest Fedora. I've included diagnostics, however 'frame_buttons', 'frame_wheel_srolling', 'pen_buttons', 'pen_coords', 'pen_pressure' and 'pen_tilt' produced empty documents.
> >  > > > > > > > > > > > >>
> >  > > > > > > > > > > > >> Any help/advice would be appreciated.
> >  > > > > > > > > > > > >
> >  > > > > > > > > > > >
> >  > > > > > > > > >
> >  > > > > > > >
> >  > > > > >
> >  > > >
> >  >
> 
 		 	   		  

------------------------------------------------------------------------------

Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server

from Actuate! Instantly Supercharge Your Business Reports and Dashboards

with Interactivity, Sharing, Native Excel Exports, App Integration & more

Get technology previously reserved for billion-dollar corporations, FREE

http://pubads.g.doubleclick.net/gampad/clk?id=157005751&iu=/4140/ostg.clktrk
_______________________________________________

DIGImend-devel mailing list

DIG...@li...

https://lists.sourceforge.net/lists/listinfo/digimend-devel