Menu
▾
▴
Re: [Devmon] probe monitoring present / not present no snmp data found
|
From: Ken C. <kco...@ry...> - 2016-01-26 14:02:58
|
Also note, I've seen where I have had an incorrect oid within one test-template, and that snowballs and kills other tests which where previously fine. So I'd do some baby-steps and strip down the template testing one test at a time and adding other tests as things go well. On Jan 26, 2016 8:22 AM, "Steve B" <rec...@gm...> wrote: > Hi Wim, > > here is what I have in the ibmups template I have made (in terms of oids) > > check/column:batt-capacity > > upsBatteryStatus : .1.3.6.1.2.1.33.1.2.1.0 : leaf > upsEstimatedminsrem : .1.3.6.1.2.1.33.1.2.3.0 : leaf > upsEstimateChargerem : .1.3.6.1.2.1.33.1.2.4.0 : leaf > upsBattVoltage : .1.3.6.1.2.1.33.1.2.5.0 : leaf > > check/column:ibmupspwr > > inputvolt : .1.3.6.1.2.1.33.1.3.3.1.3.1 : leaf > inputfreq : .1.3.6.1.2.1.33.1.3.3.1.2.1 : leaf > outputvolt : .1.3.6.1.2.1.33.1.4.4.1.2.1 : leaf > outputcurr : .1.3.6.1.2.1.33.1.4.4.1.3.1 : leaf > outputpwr : .1.3.6.1.2.1.33.1.4.4.1.4.1 : leaf > outputloadlvl : .1.3.6.1.2.1.33.1.4.4.1.5.1 : leaf > > check/column:ibmupstmp > > IBMTemp : 1.3.6.1.4.1.534.1.6.5.0 : leaf > IBMHumi : 1.3.6.1.4.1.534.1.6.6.0 : leaf > > For temperature output, it says unknown and the other checks all have > unknown/no data (with no SNMP data in logs) > > Is it perhaps something to do with the ending in 0 or not? I do remember > testing those out. > > On Tue, Jan 26, 2016 at 2:06 PM, W.J.M. Nelis <Wim...@nl...> wrote: > > > Hello Steve, > > > > >> any ideas on this one? I am monitoring 2 IBM UPS devices (per site) > and > > >> testing temperature/humidity snmp monitoring which gives results if > > probe > > >> is installed. So I have a temp check, battery capacity and power. > When > > the > > >> probe is installed, I have results for all these checks but if I > remove > > the > > >> probe, the temp check gives unknown as entries and this spreads to the > > >> other checks for that host with the dreaded "No SNMP data found > > for...." in > > >> the logs so I get white faces and greens with barely any results > (there > > are > > >> a few). > > > > > Unfortunately I have seen the 'No SNMP data found' quite a lot. > > > > > > "Are the variables in the templates in use linked with one another > > > somehow?" > > > > > > Do the oid names have to be different for every template (if the oids > > > themselves are different). Is this something I could use to look into > why > > > this is happening. Just seems a shame that none of the checks for that > > host > > > don't work if the probe is not present. I am looking into making an > > > alternate template for probe present but it's a massive cleanup job, I > > have > > > over 3k hosts world wide. > > > > > No, the OID names are so to say 'local to the template'. However, your > > complaint is about various tests within the same template. Form the > > documentation file called TEMPLATES: > > > > Also important to note is that OIDs are shared between tests > > on the same template. So if you specify OID aliases with > > identical names (they are case sensitive, remember) in multiple > > tests in a template, there is only going to be a single value > > stored in memory, which both OID aliases point to. The upshot > > of this is, if you use the same OID alias in multiple tests > > (and this is recommended, as it will make your template run > > faster), then they *MUST* have the numeric OID value. If > > they dont, you are going to get inconsistent results, as > > the value stored in memory might arbitrarily be from one SNMP > > variable or another. > > > > To rephrase my question: do you have OIDs in the various tests with the > > same name while they represent different things? > > > > Regards, > > Wim Nelis. > > > > > > > > > > > > > ------------------------------------------------------------------------------ > > Site24x7 APM Insight: Get Deep Visibility into Application Performance > > APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month > > Monitor end-to-end web transactions and take corrective actions now > > Troubleshoot faster and improve end-user experience. Signup Now! > > http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 > > _______________________________________________ > > Devmon-support mailing list > > Dev...@li... > > https://lists.sourceforge.net/lists/listinfo/devmon-support > > > > ------------------------------------------------------------------------------ > Site24x7 APM Insight: Get Deep Visibility into Application Performance > APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month > Monitor end-to-end web transactions and take corrective actions now > Troubleshoot faster and improve end-user experience. Signup Now! > http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140 > _______________________________________________ > Devmon-support mailing list > Dev...@li... > https://lists.sourceforge.net/lists/listinfo/devmon-support > |
