Re: [Devmon] HP Proliant DL380 G6

[Colin C. <col...@gm...>]

Hmm, that was a little light on detail...

OK, these are a mix of RHEL5 and RHEL6, all x86_64.  They're running
the supplied net-snmp SNMP daemon.  Also installed are hp-health,
hp-snmp-agents and hpacucli from the Proliant Support Packs.

snmpwalk works fine.

Looking at templates/compaq-server/raid/transforms, I see
"cntrlModTxt" only goes up to 34 whereas the DL380 G6 is reporting
"39"
---
snmpwalk -v2c -c CENSOR 192.168.10.56 1.3.6.1.4.1.232.3.2.2.1.1.2
SNMPv2-SMI::enterprises.232.3.2.2.1.1.2.0 = INTEGER: 39
---

I've configured SNMP and pointed devmon at a couple more G6s and found
that only the initial two G6s are reporting the badness (see attached
.png file).  The other G6s are reporting OK for condition and status.

I've run hpacucli:
---
HP Array Configuration Utility CLI 8.60-8.0
Detecting Controllers...Done.
Type "help" for a list of supported commands.
Type "exit" to close the console.

=> controller slot=0 show

Smart Array P410i in Slot 0 (Embedded)
   Bus Interface: PCI
   Slot: 0
   Serial Number: .censored.
   Cache Serial Number: .censored.
   RAID 6 (ADG) Status: Disabled
   Controller Status: OK
   Chassis Slot:
   Hardware Revision: Rev C
   Firmware Version: 3.00
   Rebuild Priority: Medium
   Expand Priority: Medium
   Surface Scan Delay: 15 secs
   Surface Scan Mode: Idle
   Queue Depth: Automatic
   Monitor and Performance Delay: 60 min
   Elevator Sort: Enabled
   Degraded Performance Optimization: Disabled
   Inconsistency Repair Policy: Disabled
   Wait for Cache Room: Disabled
   Surface Analysis Inconsistency Notification: Disabled
   Post Prompt Timeout: 0 secs
   Cache Board Present: True
   Cache Status: Permanently Disabled
   Accelerator Ratio: 25% Read / 75% Write
   Drive Write Cache: Disabled
   Total Cache Size: 512 MB
   No-Battery Write Cache: Disabled
   Cache Backup Power Source: Batteries
   Battery/Capacitor Count: 1
   Battery/Capacitor Status: OK
   SATA NCQ Supported: True

=>
---

The only thing that I can that is different between the systems
reporting OK and those not reporting OK is on the cache status line.
Thos reporting OK have a cache status of OK, the others have a cache
status of "permanently disabled".

Thanks

CC

On Thu, Jan 27, 2011 at 10:08 PM, Root, Paul <Pau...@qw...> wrote:
> So what's running your snmpd? Are you trying to look at the Lom, or are you going into the OS?
>
> How is it configured. What do you get when you do an snmpwalk (just system) of the machine?
>
>
> Paul Root
> Lead Internet Systems Eng
> Qwest Network Services
>
>
> -----Original Message-----
> From: Colin Coe [mailto:col...@gm...]
> Sent: Thursday, January 27, 2011 12:54 AM
> To: dev...@li...
> Subject: [Devmon] HP Proliant DL380 G6
>
> Hi all
>
> I'm getting 'unknown' as the model number for the DL380 G6's that I'm
> monitoring as well as condition of degraded and status of general
> failure.
>
> Is anyone else seeing this?
>
> Thanks
>
> CC
>
> --
> RHCE#805007969328369
>
> ------------------------------------------------------------------------------
> Special Offer-- Download ArcSight Logger for FREE (a $49 USD value)!
> Finally, a world-class log management solution at an even better price-free!
> Download using promo code Free_Logger_4_Dev2Dev. Offer expires
> February 28th, so secure your free ArcSight Logger TODAY!
> http://p.sf.net/sfu/arcsight-sfd2d
> _______________________________________________
> Devmon-support mailing list
> Dev...@li...
> https://lists.sourceforge.net/lists/listinfo/devmon-support
>

-- 
RHCE#805007969328369