Re: [Devil-Linux-discuss] devil-linux-1.4RC4 default gateway

[Serge L. <ser...@gm...>]

Bogdan,

you are welcome

Serge

On 09/28/2010 08:33 PM, Bogdan Petrisor wrote:
> I removed DHCP from eth0 and seems to work now
> The thing is my DSL router (TP-Link) has a DHCP server even when you set it in bridge mode and I thought it was a good idea to enable it on my gateway too. It worked until now so I completely ignored this setting.
> 
> Again thank you for your help and keep up the good work 
> 
> --------------------------------
> In the beginning there was nothing. Then, God said, "Let there be light". 
> And there was still nothing, but at least you could see it.
> --------------------------------
> 
> 
> --- On Mon, 9/27/10, Bogdan Petrisor <pet...@ya...> wrote:
> 
>> From: Bogdan Petrisor <pet...@ya...>
>> Subject: Re: [Devil-Linux-discuss] devil-linux-1.4RC4 default gateway
>> To: dev...@li...
>> Date: Monday, September 27, 2010, 10:35 PM
>> Hi Serge,
>>
>> I'll try this tomorrow (it's a bit late here) and let you
>> know how it works.
>> The DSL modem should be in bridge mode, I'll check that too
>> ...
>>
>> Thank you for your time
>>
>> --------------------------------
>> In the beginning there was nothing. Then, God said, "Let
>> there be light". 
>> And there was still nothing, but at least you could see
>> it.
>> --------------------------------
>>
>>
>> --- On Mon, 9/27/10, Serge Leschinsky
>> <ser...@gm...>
>> wrote:
>>
>>> From: Serge Leschinsky <ser...@gm...>
>>> Subject: Re: [Devil-Linux-discuss] devil-linux-1.4RC4
>> default gateway
>>> To: dev...@li...
>>> Date: Monday, September 27, 2010, 2:40 AM
>>> Hi Bogdan,
>>>
>>> After some tests I'm sure that pppoe server and client
>> on
>>> DL work correctly. The
>>> specific of pppd behavior is declared in
>>> '/usr/sbin/pppoe-start' script (and in
>>> log file if you start pppoe in debug mode)
>>>
>>> $ECHO "* The following section lists your routing
>> table."
>>>>> $DEBUG
>>> $ECHO "* If you have an entry which starts with
>> '0.0.0.0',
>>> you probably" >> $DEBUG
>>> $ECHO "* have defined a default route and gateway, and
>> pppd
>>> will" >> $DEBUG
>>> $ECHO "* not create a default route using your ISP. 
>>> Try getting" >> $DEBUG
>>> $ECHO "* rid of this route." >> $DEBUG
>>>
>>> Unfortunately, I still don't understand your setup. If
>> your
>>> adsl modem works in
>>> bridge mode, it shouldn’t respond on DHCP, if it's
>> in
>>> router mode - there is no
>>> necessity to use pppoe... Assuming that it's in brige
>> mode
>>> I'd suggest keeping
>>> the interface connected to adsl modem unconfigured
>> (i.e.
>>> set "DHCP=no" in the
>>> config you posted) or add a line to adsl init script
>> which
>>> will remove default
>>> gateway before pppd starting.
>>>
>>> Serge
>>>
>>> On 09/19/2010 08:15 PM, Bogdan Petrisor wrote:
>>>> Hi Serge,
>>>>
>>>> root@annuminas:~ # cat
>> /etc/sysconfig/nic/ifcfg-eth0
>>>> DEVICE=eth0
>>>> ONBOOT=yes
>>>> MODULE="8139too"
>>>> DHCP=yes
>>>> IP=
>>>> NETMASK=
>>>> BROADCAST=""
>>>
>>> .....
>>>
>>>