Thread: [Co800-test] Gentoo: co800 -in: I can't find busses, and much more errors!!
Brought to you by:
ppasamonte
Menu
▾
▴
co800-test
|
From: <ed...@fe...> - 2003-06-11 15:33:11
|
Hi all,
I'm spanish but I write this in english because I hope that much more mor=
e
people could help this way.
I'm using a mostly fresh gentoo 1.4, and trying to use the ambipur (coppe=
rjet)
in linux. No luck.
I've had some probs, but finally I could compiled co800 (I compiled it as=
the
README file). Also I've configured the network (my ip, netmask, gw, dns1,=
dns2).
all done using a kernel with the usb drivers (uhci, ohci inclusive ohci) =
buit-in
and not as modules. Also, linux-atm was not well compiled at the time of
compiling co800 (later I found that it wouln't compile since i wanted to =
compile
linux-atm in a partition owned by users, and this seem not possible).
After all, when I run co800 -in, it says:
////////////////////////////////////////////////////////////////////////
(shell)# co800 -in
co800 -in: I can't find busses
co800 -in: I can't find busses
////////////////////////////////////////////////////////////////////////
No matter if the modem is connected to the pc or not!! (So you can guess =
that
the leds of the modem don't change. They're exacly like when the modem is
disconnected from the computer).
Then I compiled linux-atm, which seems to work. co800 -in tells me the sa=
me
error. So I tried to compile the kenrel with uhci and ohci as modules, bu=
t when
I try to insmod usb-ohci, it gives me the above errors:
////////////////////////////////////////////////////////////////////////
/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: init_module:=
No
such device
Hint: insmod errors can be caused by incorrect module parameters, includi=
ng
invalid IO or IRQ parameters.
/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod
/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o failed
/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod usb-o=
hci failed
You may find more information in syslog or the output from dmesg
////////////////////////////////////////////////////////////////////////
So I went back to use the kenrel with ohci built-in, with seems to work w=
ell
enought. So what to do now? Let's try to re-compile co800 right? Oh my, n=
ow it
can't, it makes me the following errors (Note: I'll wirte the entire inst=
all
process so you can see if it's correct):
////////////////////////////////////////////////////////////////////////
(shell)# tar zxf co800_static_IP_v1.0.0_beta.tar.gz
cd co800_static_IP_v1.0.0_beta/
(shell)# nano -w Makefile (LINUX_DIR=3D/usr/src/linux)
(shell)# make
make -C fwload
make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload'
cc -I../lib/libusb -lusb 5160.c common.o -o 5160
/tmp/ccy8IUXk.o(.text+0x40): In function `send_bulk':
: referencia a `usb_bulk_write' sin definir
/tmp/ccy8IUXk.o(.text+0x5d): In function `send_bulk':
: referencia a `usb_strerror' sin definir
/tmp/ccy8IUXk.o(.text+0x2ff): In function `main':
: referencia a `usb_init' sin definir
/tmp/ccy8IUXk.o(.text+0x304): In function `main':
: referencia a `usb_find_busses' sin definir
/tmp/ccy8IUXk.o(.text+0x325): In function `main':
: referencia a `usb_find_devices' sin definir
/tmp/ccy8IUXk.o(.text+0x346): In function `main':
: referencia a `usb_busses' sin definir
/tmp/ccy8IUXk.o(.text+0x44c): In function `main':
: referencia a `usb_open' sin definir
/tmp/ccy8IUXk.o(.text+0x48b): In function `main':
: referencia a `usb_claim_interface' sin definir
/tmp/ccy8IUXk.o(.text+0x494): In function `main':
: referencia a `usb_strerror' sin definir
/tmp/ccy8IUXk.o(.text+0x4af): In function `main':
: referencia a `usb_close' sin definir
/tmp/ccy8IUXk.o(.text+0x4ea): In function `main':
: referencia a `usb_close' sin definir
/tmp/ccy8IUXk.o(.text+0x4fe): In function `main':
: referencia a `usb_close' sin definir
common.o(.text+0x44): In function `get_descriptor':
: referencia a `usb_control_msg' sin definir
common.o(.text+0x4e): In function `get_descriptor':
: referencia a `usb_strerror' sin definir
common.o(.text+0x10d): In function `get_descriptor2':
: referencia a `usb_control_msg' sin definir
common.o(.text+0x121): In function `get_descriptor2':
: referencia a `usb_strerror' sin definir
collect2: ld devolvi=F3 el estado de salida 1
make[1]: *** [5160] Error 1
make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload'
make: *** [all] Error 2
(shell)# make install // (Let's see what it gives)
(shell)# make install
make -C fwload
make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload'
cc -I../lib/libusb -lusb 5160.c common.o -o 5160
/tmp/ccIW80Jn.o(.text+0x40): In function `send_bulk':
: referencia a `usb_bulk_write' sin definir
/tmp/ccIW80Jn.o(.text+0x5d): In function `send_bulk':
: referencia a `usb_strerror' sin definir
/tmp/ccIW80Jn.o(.text+0x2ff): In function `main':
: referencia a `usb_init' sin definir
/tmp/ccIW80Jn.o(.text+0x304): In function `main':
: referencia a `usb_find_busses' sin definir
/tmp/ccIW80Jn.o(.text+0x325): In function `main':
: referencia a `usb_find_devices' sin definir
/tmp/ccIW80Jn.o(.text+0x346): In function `main':
: referencia a `usb_busses' sin definir
/tmp/ccIW80Jn.o(.text+0x44c): In function `main':
: referencia a `usb_open' sin definir
/tmp/ccIW80Jn.o(.text+0x48b): In function `main':
: referencia a `usb_claim_interface' sin definir
/tmp/ccIW80Jn.o(.text+0x494): In function `main':
: referencia a `usb_strerror' sin definir
/tmp/ccIW80Jn.o(.text+0x4af): In function `main':
: referencia a `usb_close' sin definir
/tmp/ccIW80Jn.o(.text+0x4ea): In function `main':
: referencia a `usb_close' sin definir
/tmp/ccIW80Jn.o(.text+0x4fe): In function `main':
: referencia a `usb_close' sin definir
common.o(.text+0x44): In function `get_descriptor':
: referencia a `usb_control_msg' sin definir
common.o(.text+0x4e): In function `get_descriptor':
: referencia a `usb_strerror' sin definir
common.o(.text+0x10d): In function `get_descriptor2':
: referencia a `usb_control_msg' sin definir
common.o(.text+0x121): In function `get_descriptor2':
: referencia a `usb_strerror' sin definir
collect2: ld devolvi=F3 el estado de salida 1
make[1]: *** [5160] Error 1
make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload'
make: *** [all] Error 2
////////////////////////////////////////////////////////////////////////
Any one knows something I should ? any question, any help ? anything, ple=
ase ?
Thanks for your time,
|
|
From: Tritt <zer...@so...> - 2003-06-13 11:11:18
|
ed...@fe... wrote: >Hi all, > >I'm spanish but I write this in english because I hope that much more more >people could help this way. > Hi, i´m spanish too :D. Sorry for my english. >I'm using a mostly fresh gentoo 1.4, and trying to use the ambipur (copperjet) >in linux. No luck. > >I've had some probs, but finally I could compiled co800 (I compiled it as the >README file). Also I've configured the network (my ip, netmask, gw, dns1, dns2). all done using a kernel with the usb drivers (uhci, ohci inclusive ohci) buit-in and not as modules. Also, linux-atm was not well compiled at the time of compiling co800 (later I found that it wouln't compile since i wanted to compile >linux-atm in a partition owned by users, and this seem not possible). > >After all, when I run co800 -in, it says: > >//////////////////////////////////////////////////////////////////////// >(shell)# co800 -in >co800 -in: I can't find busses >co800 -in: I can't find busses >//////////////////////////////////////////////////////////////////////// > >No matter if the modem is connected to the pc or not!! (So you can guess that >the leds of the modem don't change. They're exacly like when the modem is >disconnected from the computer). > If the leds are like when the modem is disconnected it´s sure youve got a problem whit usb power. Look in your BIOS to enable usb. > >Then I compiled linux-atm, which seems to work. co800 -in tells me the same >error. So I tried to compile the kenrel with uhci and ohci as modules, but when >I try to insmod usb-ohci, it gives me the above errors: > >//////////////////////////////////////////////////////////////////////// >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: init_module: No >such device >Hint: insmod errors can be caused by incorrect module parameters, including >invalid IO or IRQ parameters. >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o failed >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod usb-ohci failed > You may find more information in syslog or the output from dmesg >//////////////////////////////////////////////////////////////////////// > >So I went back to use the kenrel with ohci built-in, with seems to work well >enought. So what to do now? Let's try to re-compile co800 right? Oh my, now it >can't, it makes me the following errors (Note: I'll wirte the entire install >process so you can see if it's correct): > >//////////////////////////////////////////////////////////////////////// >(shell)# tar zxf co800_static_IP_v1.0.0_beta.tar.gz >cd co800_static_IP_v1.0.0_beta/ >(shell)# nano -w Makefile (LINUX_DIR=/usr/src/linux) >(shell)# make >make -C fwload >make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload' >cc -I../lib/libusb -lusb 5160.c common.o -o 5160 >/tmp/ccy8IUXk.o(.text+0x40): In function `send_bulk': >: referencia a `usb_bulk_write' sin definir >/tmp/ccy8IUXk.o(.text+0x5d): In function `send_bulk': >: referencia a `usb_strerror' sin definir >/tmp/ccy8IUXk.o(.text+0x2ff): In function `main': >: referencia a `usb_init' sin definir >/tmp/ccy8IUXk.o(.text+0x304): In function `main': >: referencia a `usb_find_busses' sin definir >/tmp/ccy8IUXk.o(.text+0x325): In function `main': >: referencia a `usb_find_devices' sin definir >/tmp/ccy8IUXk.o(.text+0x346): In function `main': >: referencia a `usb_busses' sin definir >/tmp/ccy8IUXk.o(.text+0x44c): In function `main': >: referencia a `usb_open' sin definir >/tmp/ccy8IUXk.o(.text+0x48b): In function `main': >: referencia a `usb_claim_interface' sin definir >/tmp/ccy8IUXk.o(.text+0x494): In function `main': >: referencia a `usb_strerror' sin definir >/tmp/ccy8IUXk.o(.text+0x4af): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccy8IUXk.o(.text+0x4ea): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccy8IUXk.o(.text+0x4fe): In function `main': >: referencia a `usb_close' sin definir >common.o(.text+0x44): In function `get_descriptor': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x4e): In function `get_descriptor': >: referencia a `usb_strerror' sin definir >common.o(.text+0x10d): In function `get_descriptor2': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x121): In function `get_descriptor2': >: referencia a `usb_strerror' sin definir >collect2: ld devolvió el estado de salida 1 >make[1]: *** [5160] Error 1 >make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload' >make: *** [all] Error 2 >(shell)# make install // (Let's see what it gives) >(shell)# make install >make -C fwload >make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload' >cc -I../lib/libusb -lusb 5160.c common.o -o 5160 >/tmp/ccIW80Jn.o(.text+0x40): In function `send_bulk': >: referencia a `usb_bulk_write' sin definir >/tmp/ccIW80Jn.o(.text+0x5d): In function `send_bulk': >: referencia a `usb_strerror' sin definir >/tmp/ccIW80Jn.o(.text+0x2ff): In function `main': >: referencia a `usb_init' sin definir >/tmp/ccIW80Jn.o(.text+0x304): In function `main': >: referencia a `usb_find_busses' sin definir >/tmp/ccIW80Jn.o(.text+0x325): In function `main': >: referencia a `usb_find_devices' sin definir >/tmp/ccIW80Jn.o(.text+0x346): In function `main': >: referencia a `usb_busses' sin definir >/tmp/ccIW80Jn.o(.text+0x44c): In function `main': >: referencia a `usb_open' sin definir >/tmp/ccIW80Jn.o(.text+0x48b): In function `main': >: referencia a `usb_claim_interface' sin definir >/tmp/ccIW80Jn.o(.text+0x494): In function `main': >: referencia a `usb_strerror' sin definir >/tmp/ccIW80Jn.o(.text+0x4af): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccIW80Jn.o(.text+0x4ea): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccIW80Jn.o(.text+0x4fe): In function `main': >: referencia a `usb_close' sin definir >common.o(.text+0x44): In function `get_descriptor': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x4e): In function `get_descriptor': >: referencia a `usb_strerror' sin definir >common.o(.text+0x10d): In function `get_descriptor2': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x121): In function `get_descriptor2': >: referencia a `usb_strerror' sin definir >collect2: ld devolvió el estado de salida 1 >make[1]: *** [5160] Error 1 >make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload' >make: *** [all] Error 2 >//////////////////////////////////////////////////////////////////////// > Gentoo, hmmm. I´ve used gentoo not much time ago and they used some kind of kernel hacked. Try the vanilla kernel. > >Any one knows something I should ? any question, any help ? anything, please ? > >Thanks for your time, > > > Perdona mi ingles, pero parece que hay gente no castellano-parlante por aqui y es mejor que nos entendamos todos. Si no entiendes algo dimelo, que para eso estamos. |
|
From: Jean-frederic C. <jf...@si...> - 2003-06-13 20:53:29
|
ed...@fe... wrote: >Hi all, > >I'm spanish but I write this in english because I hope that much more more >people could help this way. > >I'm using a mostly fresh gentoo 1.4, and trying to use the ambipur (copperjet) >in linux. No luck. > >I've had some probs, but finally I could compiled co800 (I compiled it as the >README file). Also I've configured the network (my ip, netmask, gw, dns1, dns2). > >all done using a kernel with the usb drivers (uhci, ohci inclusive ohci) buit-in >and not as modules. Also, linux-atm was not well compiled at the time of >compiling co800 (later I found that it wouln't compile since i wanted to compile >linux-atm in a partition owned by users, and this seem not possible). > >After all, when I run co800 -in, it says: > >//////////////////////////////////////////////////////////////////////// >(shell)# co800 -in >co800 -in: I can't find busses >co800 -in: I can't find busses >//////////////////////////////////////////////////////////////////////// > >No matter if the modem is connected to the pc or not!! (So you can guess that >the leds of the modem don't change. They're exacly like when the modem is >disconnected from the computer). > Sure, It seems the devusb is not mount I have: +++ jfclere@jfcexpert:~> mount /dev/hda1 on / type reiserfs (rw) proc on /proc type proc (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) /dev/hda3 on /home type reiserfs (rw) shmfs on /dev/shm type shm (rw) usbdevfs on /proc/bus/usb type usbdevfs (rw,mode=0662) +++ I have in my /etc/fstab: +++ jfclere@jfcexpert:~> more /etc/fstab /dev/hda1 / reiserfs defaults 1 1 /dev/hda3 /home reiserfs defaults 1 2 /dev/hda2 swap swap pri=42 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 proc /proc proc defaults 0 0 usbdevfs /proc/bus/usb usbdevfs noauto,mode=0662 0 0 /dev/cdrecorder /media/cdrecorder auto ro,noauto,user,exec 0 0 /dev/cdrom /media/cdrom auto ro,noauto,user,exec 0 0 /dev/dvd /media/dvd auto ro,noauto,user,exec 0 0 /dev/fd0 /media/floppy auto noauto,user,sync 0 0 +++ > >Then I compiled linux-atm, which seems to work. co800 -in tells me the same >error. So I tried to compile the kenrel with uhci and ohci as modules, but when >I try to insmod usb-ohci, it gives me the above errors: > >//////////////////////////////////////////////////////////////////////// >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: init_module: No >such device > That is "normal", there are 2 types of usb boards. uhci and ohci... Of course you (normal) need only one, the other will give an error. >Hint: insmod errors can be caused by incorrect module parameters, including >invalid IO or IRQ parameters. >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o failed >/lib/modules/2.4.20-gentoo-r5/kernel/drivers/usb/usb-ohci.o: insmod usb-ohci failed > You may find more information in syslog or the output from dmesg >//////////////////////////////////////////////////////////////////////// > >So I went back to use the kenrel with ohci built-in, with seems to work well >enought. So what to do now? Let's try to re-compile co800 right? Oh my, now it >can't, it makes me the following errors (Note: I'll wirte the entire install >process so you can see if it's correct): > >//////////////////////////////////////////////////////////////////////// >(shell)# tar zxf co800_static_IP_v1.0.0_beta.tar.gz >cd co800_static_IP_v1.0.0_beta/ >(shell)# nano -w Makefile (LINUX_DIR=/usr/src/linux) >(shell)# make >make -C fwload >make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload' >cc -I../lib/libusb -lusb 5160.c common.o -o 5160 >/tmp/ccy8IUXk.o(.text+0x40): In function `send_bulk': >: referencia a `usb_bulk_write' sin definir >/tmp/ccy8IUXk.o(.text+0x5d): In function `send_bulk': >: referencia a `usb_strerror' sin definir >/tmp/ccy8IUXk.o(.text+0x2ff): In function `main': >: referencia a `usb_init' sin definir >/tmp/ccy8IUXk.o(.text+0x304): In function `main': >: referencia a `usb_find_busses' sin definir >/tmp/ccy8IUXk.o(.text+0x325): In function `main': >: referencia a `usb_find_devices' sin definir >/tmp/ccy8IUXk.o(.text+0x346): In function `main': >: referencia a `usb_busses' sin definir >/tmp/ccy8IUXk.o(.text+0x44c): In function `main': >: referencia a `usb_open' sin definir >/tmp/ccy8IUXk.o(.text+0x48b): In function `main': >: referencia a `usb_claim_interface' sin definir >/tmp/ccy8IUXk.o(.text+0x494): In function `main': >: referencia a `usb_strerror' sin definir >/tmp/ccy8IUXk.o(.text+0x4af): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccy8IUXk.o(.text+0x4ea): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccy8IUXk.o(.text+0x4fe): In function `main': >: referencia a `usb_close' sin definir >common.o(.text+0x44): In function `get_descriptor': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x4e): In function `get_descriptor': >: referencia a `usb_strerror' sin definir >common.o(.text+0x10d): In function `get_descriptor2': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x121): In function `get_descriptor2': >: referencia a `usb_strerror' sin definir >collect2: ld devolvió el estado de salida 1 >make[1]: *** [5160] Error 1 >make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload' >make: *** [all] Error 2 >(shell)# make install // (Let's see what it gives) >(shell)# make install >make -C fwload >make[1]: Entering directory `/root/co800_static_IP_v1.0.0_beta/fwload' >cc -I../lib/libusb -lusb 5160.c common.o -o 5160 >/tmp/ccIW80Jn.o(.text+0x40): In function `send_bulk': >: referencia a `usb_bulk_write' sin definir >/tmp/ccIW80Jn.o(.text+0x5d): In function `send_bulk': >: referencia a `usb_strerror' sin definir >/tmp/ccIW80Jn.o(.text+0x2ff): In function `main': >: referencia a `usb_init' sin definir >/tmp/ccIW80Jn.o(.text+0x304): In function `main': >: referencia a `usb_find_busses' sin definir >/tmp/ccIW80Jn.o(.text+0x325): In function `main': >: referencia a `usb_find_devices' sin definir >/tmp/ccIW80Jn.o(.text+0x346): In function `main': >: referencia a `usb_busses' sin definir >/tmp/ccIW80Jn.o(.text+0x44c): In function `main': >: referencia a `usb_open' sin definir >/tmp/ccIW80Jn.o(.text+0x48b): In function `main': >: referencia a `usb_claim_interface' sin definir >/tmp/ccIW80Jn.o(.text+0x494): In function `main': >: referencia a `usb_strerror' sin definir >/tmp/ccIW80Jn.o(.text+0x4af): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccIW80Jn.o(.text+0x4ea): In function `main': >: referencia a `usb_close' sin definir >/tmp/ccIW80Jn.o(.text+0x4fe): In function `main': >: referencia a `usb_close' sin definir >common.o(.text+0x44): In function `get_descriptor': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x4e): In function `get_descriptor': >: referencia a `usb_strerror' sin definir >common.o(.text+0x10d): In function `get_descriptor2': >: referencia a `usb_control_msg' sin definir >common.o(.text+0x121): In function `get_descriptor2': >: referencia a `usb_strerror' sin definir >collect2: ld devolvió el estado de salida 1 >make[1]: *** [5160] Error 1 >make[1]: Leaving directory `/root/co800_static_IP_v1.0.0_beta/fwload' >make: *** [all] Error 2 >//////////////////////////////////////////////////////////////////////// > >Any one knows something I should ? any question, any help ? anything, please ? > Wrong usb library? > >Thanks for your time, > You are welcome :-) > > >------------------------------------------------------- >This SF.NET email is sponsored by: eBay >Great deals on office technology -- on eBay now! Click here: >http://adfarm.mediaplex.com/ad/ck/711-11697-6916-5 >_______________________________________________ >Co800-test mailing list >Co8...@li... >https://lists.sourceforge.net/lists/listinfo/co800-test > > > > |
Thanks for helping keep SourceForge clean.
X