bwm-tools-tech

[bwm-tools-tech] Next Question .. What means "Segmentation fault" ?

[<ral...@ra...>]

Hi Again,

over the weekend i try many think, that the traffic control works.

Now i'm a little bit farhter, because the traffic control works by P2P and ftp traffic.
Think there is a big mistake in my firewall rules, because when this work, i can't open
any websites or many other thinks.
Is this idea the right way or can be anythink other wrong ?

Ok, by this test i want to look over the bwm_monitor, how the bwm_tool works.
So i start the bwm_monitor, but nothing happen !
After canceling the prozess i become the errormessage "Segmentation fault".

So i try anythink and i find out .....
. that when i chance in the acl-table the targets from -j bwmd to -j ACCEPT then the
bwm_monitor start without problems.
What is here wrong ? 
Is there a mistake in my firewall.xml ?

Then i have a question to the traffic-control ...
How differ the flow table between input and output ? 
Is this only the option "in" and "out" in the name from the flow-table.

Thanks for answer !



best Regards

Ralph Buchmann

To: nk...@lb...
    bwm...@li...

Re: [bwm-tools-tech] Next Question .. What means "Segmentation fault" ?

[Nigel K. <nk...@lb...>]

Hi Ralph,

If you getting "segmentation fault" from any of the bwm tools utilities,
this is bad. Is it reproducable?

Can you send me the steps you took, including configuration files that
led to the segfault?


Thanks
Nigel

ral...@ra... wrote:

>
> Hi Again,
>
> over the weekend i try many think, that the traffic control works.
>
> Now i'm a little bit farhter, because the traffic control works by P2P
> and ftp traffic.
> Think there is a big mistake in my firewall rules, because when this
> work, i can't open
> any websites or many other thinks.
> Is this idea the right way or can be anythink other wrong ?
>
> Ok, by this test i want to look over the bwm_monitor, how the bwm_tool
> works.
> So i start the bwm_monitor, but nothing happen !
> After canceling the prozess i become the errormessage "Segmentation
> fault".
>
> So i try anythink and i find out .....
> .. that when i chance in the acl-table the targets from -j bwmd to -j
> ACCEPT then the
> bwm_monitor start without problems.
> What is here wrong ?
> Is there a mistake in my firewall.xml ?
>
> Then i have a question to the traffic-control ..
> How differ the flow table between input and output ?
> Is this only the option "in" and "out" in the name from the flow-table.
>
> Thanks for answer !
>
>
>
> best Regards
>
> Ralph Buchmann
>
>
> To: nk...@lb...
>     bwm...@li...


--
Nigel Kukard, PhD CompSc
(Chief Executive Officer)
Linux Based Systems Design
Web: www.lbsd.net          Email: nk...@lb...
Tel: (+27) 023 349 8000     Cell: (+27) 082 333 3723
Fax: (+27) 023 349 1395  Support: 086 747 7600
Address: LIGT House, 2 Klipdrift Rd, Rawsonville
Linux Systems Design & Technology Solutions


   The best language to use is the language that was designed for
                  what you want to use it for.


=====================================================================

Disclaimer
----------
The contents of this message and any attachments are intended
solely for the addressee's use and may be legally privileged and/or
confidential information. This message may not be retained,
distributed, copied or used if you are not he addressee of this
message. If this message was sent to you in error, please notify
the sender immediately by reply e-mail and then destroy the message
and any copies thereof.

Opinions, conclusions and other information in this message may be
personal to the sender and is not that of Linux Based Systems Design,
LinuxRulz or any of it's subsideries, associated companies or
principals and is therefore not endorsed by Linux Based Systems
Design or LinuxRulz. Due to e-maill communication being insecure,
Linux Based Systems Design and LinuxRulz do not guarantee
confidentiality, security, accuracy or performance of the e-mail.
Any liability for viruses is excluded to the fullest extent.