#14 modules vrs built in kernel
Hello-
Does the bonding code work if built into the kernel(not
using modules)?
The reason I ask:
built a 2.4.21 kernel without module support but with
the bonding bits.
I can bond 2 interfaces together but can not reach or
see the other end. This is 2 linux machines connected
via a pair of cross over cables.
The files I created/edit are:
/etc/sysconfig/network-scripts/ifcfg-bond0
/etc/sysconfig/network-scripts/ifcfg-eth1
/etc/sysconfig/network-scripts/ifcfg-eth2
the howto mentions to add the below line to
modules.conf but since i am not using modules I'd
suspect this is not even looked at.. correct?
alias bond0 bonding
options bond0 miimon=200 mode=1
thanks folks.
greg
Here is some info / contents of files on the system:
/etc/sysconfig/network-scripts/ifcfg-*
ifcfg-eth0:
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR=172.16.92.244
NETMASK=255.255.252.0
GATEWAY=172.16.92.2
ifcfg-eth1:
DEVICE=eth1
BOOTPROTO=none
ONBOOT=yes
USERCTL=no
MASTER=bond0
SLAVE=yes
ifcfg-eth2:
DEVICE=eth2
BOOTPROTO=none
ONBOOT=yes
MASTER=bond0
SLAVE=yes
USERCTL=no
ifcfg-bond0:
DEVICE=bond0
IPADDR=192.168.1.1
NETMASK=255.255.255.0
NETWORK=192.168.1.0
BROADCAST=192.168.1.255
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
modules.conf(?)
options bond0 miimon=200 mode=1
(the above was added afterwards in an attempt to fix
things)
[root@nova root]# ifconfig
bond0 Link encap:Ethernet HWaddr 00:09:6B:63:37:E7
inet addr:192.168.1.1 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST
MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:6 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:3852 (3.7 Kb)
eth0 Link encap:Ethernet HWaddr 00:03:47:DE:29:37
inet addr:172.16.92.244 Bcast:172.16.95.255
Mask:255.255.252.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:3555 errors:0 dropped:0 overruns:0
frame:0
TX packets:2173 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:100
RX bytes:458454 (447.7 Kb) TX bytes:410930
(401.2 Kb)
Interrupt:16 Memory:febc0000-febe0000
eth1 Link encap:Ethernet HWaddr 00:09:6B:63:37:E7
inet addr:192.168.1.1 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING SLAVE MULTICAST
MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:3 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:1926 (1.8 Kb)
Interrupt:24
eth2 Link encap:Ethernet HWaddr 00:09:6B:63:37:E7
inet addr:192.168.1.1 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING SLAVE MULTICAST
MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:3 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:1926 (1.8 Kb)
Interrupt:25
Sep 2 14:45:52 nova kernel: e1000: eth0 NIC Link is Up
1000 Mbps Full Duplex
Sep 2 14:45:52 nova kernel: bond0: enslaving eth1 as
an active interface with an up link.
Sep 2 14:45:52 nova kernel: bond0: enslaving eth2 as
an active interface with an up link.
Sep 2 14:45:52 nova kernel: tg3: eth1: Link is up at
1000 Mbps, full duplex.
Sep 2 14:45:53 nova kernel: tg3: eth1: Flow control is
on for TX and on for RX.
Sep 2 14:45:53 nova kernel: tg3: eth2: Link is up at
1000 Mbps, full duplex.
Sep 2 14:45:53 nova kernel: tg3: eth2: Flow control is
on for TX and on for RX.
Sep 2 14:45:53 nova kernel: Attached scsi generic sg1
at scsi0, channel 0, id 8, lun 0, type 3
Sep 2 14:46:31 nova sshd(pam_unix)[1070]: session
opened for user root by (uid=0)
Sep 2 14:47:31 nova kernel: qla2x00_set_info starts at
address = f8955060
Sep 2 14:47:31 nova kernel: qla2x00: Found VID=1077
DID=2312 SSVID=1077 SSDID=10a
Sep 2 14:47:31 nova kernel: scsi(1): Found a QLA2312
@ bus 1, device 0x2, irq 18, iobase 0x2400